Search results

Shear stresses have a considerable influence on the characteristics of lubricants and become significant at high rotating speeds. This study aims to investigate the influences of shear cavitation (SC) on loading capacity of journal bearings.

A principal normal stress cavitation criterion based on the stress applied to flowing lubricant in journal bearings is developed and used to investigate SC in journal bearings. A computational fluid dynamic (CFD) model for calculating the loading capacity is established using this criterion. After validation with experimental results, the loading capacity is calculated under different conditions.

The calculation results indicate that SC intensifies when viscosity, speed and eccentricity increase. Angle of loading capacity with SC is larger than that without SC. The magnitude of loading capacity with SC is smaller than that without SC due to the decrease in the ultimate pressure. In addition, the magnitude difference between the loading capacity with and without SC increases when viscosity, speed and eccentricity increases.

Present research can provide some guidance for calculating the loading capacity when a journal bearing is operating at high speed or with a high viscosity lubricant.

The purpose of this paper is to analyse the phenomenon of wear resistance of some metals and alloys with allowance for the stiffness of their stressed‐strained state of the surface.

An original criterion (in the form of limiting deformation power density) of wear resistance on the basis of structure‐energy theory of friction is proposed. Experimental data on the wear resistance are generalized using the criterion for the conditions of hydroabrasive, impact‐abrasive and cavitational erosion.

The dependence of the criterion on stiffness coefficient of the stressed‐strained state of the surface of materials is demonstrated. It has been found that an increase of the stiffness results in the reduction in the energy capacity and wear resistance of both metals and alloys investigated.

The structure‐energy criterion can be used for choosing suitable frictional materials and to compare and estimate the theoretical considerations with experimental data.

The proposed structure‐energy approach allows systemizing the results of our analyses and the experimental data.

The purpose of this paper is to investigate the effects of different surface structures, dimensional parameters and cavitation models on the lubrication characteristics of water-lubricated journal bearings.

In this paper, the coupling iteration method of ANSYS and MATLAB is established to calculate the journal orbits of water-lubricated bearing, and the differences between the journal orbits of the smoothed and the textured water-lubricated bearings are compared and analyzed, and the effects of different bearing materials, L/D ratios and clearance ratios on the lubrication performance of water-lubricated bearings are investigated. The effects of different cavitation models on the static equilibrium position and whirling trajectory of water-lubricated bearings are compared.

The results show that when the surface texture is distributed in the upper bearing or the bearing elastic modulus decreases, the bearing stability increases. Considering shear cavitation and noncondensing gas, the rotor journal orbits amplitude decreases at high speed with low clearance ratio. A water film test rig for water-lubricated bearings is built to measure the full-circle water film pressure of water-lubricated journal bearings, and the experimental results are compared with the simulation results, which are in good agreement.

The findings provide a theoretical basis for optimizing the structure of water-lubricated bearings.

The breakdown of laminar flow in the clearance space of a journal is considered, and the point of transition is considered in relation to experiments carried out with ‘bearings’ of large clearance. Experiments involving flow visualization with very large clearance ratios of 0.05 to 0.3 show that the laminar regime gives way to cellular or ring vertices at the critical Reynolds number predicted by G. I. Taylor for concentric cylinders even in the presence of an axial flow and at a rather higher Reynolds number in the case of eccentric cylinders. The effect of the transition on the axial flow between the cylinders is small. The critical speed for transition as deduced by Taylor, is little affected by moderate axial flows and is increased by eccentricity. The effect of critical condition on the axial‐flow characteristics of the bearing system appears to be negligible, again for moderate axial flows. Assuming that the results can be extrapolated to clearances applicable to bearing operation, the main conclusion of this paper is that the breakdown of laminar flow, which is a practical possibility in very high‐speed bearings, is delayed by eccentric operation.

Examines the tenth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

A method extensively used in the production of optically flat and finely finished surfaces is that of lapping the surface upon a plate using a loose abrasive mixed into a slurry form with a carrying fluid. If the surfaces finished in this way are in continuous or intermittent sliding contact, it is the author's opinion that any abrasives retained in their surfaces will affect surface wear. This paper reported on some exploratory work to indicate the degree of embedment of abrasive in certain materials lapped by hand.

THE first part of Professor Duncan Dowson's paper (March/April issue) dwelt on late 19th century development of machinery outstripping the performance of available lubricants. Contemporary lubricant research, and personalities involved, where described, leading to the concept of fluid‐film lubrication, documented by Professor Osborne Reynolds' paper read to the Royal Society in 1886.

Examines the ninth published year of the ITCRR. Runs the whole gamut of textile innovation, research and testing, some of which investigates hitherto untouched aspects. Subjects discussed include cotton fabric processing, asbestos substitutes, textile adjuncts to cardiovascular surgery, wet textile processes, hand evaluation, nanotechnology, thermoplastic composites, robotic ironing, protective clothing (agricultural and industrial), ecological aspects of fibre properties – to name but a few! There would appear to be no limit to the future potential for textile applications.

Looks at the eighth published year of the ITCRR and the research, from far and near, involved in this. Muses on the fact that, though all the usual processes are to the fore, the downside part of the industry is garment making which is the least developed side. Posits that the manufacture of clothing needs to become more technologically advanced as does retailing. Closes by emphasising support for the community in all its efforts.

Seeks to examine the performance of conventional turbulence models modelling strongly swirling flows within a Symmetrical Turn up Vortex Amplifier, with adjustment of the turbulence model constants to improve agreement with experimental data.

First, the standard k‐ε model and the Reynolds Stress Model (RSM) were used with standard values of model constants, using both the first order upwind and the quadratic upstream interpolation for convective kinetics (QUICK) schemes. Then, the swirling effect was corrected by adjusting the model coefficients.

The standard RSM with the QUICK did produce better predictions but still significantly overestimated the experimental data. Much improved simulation was obtained with the systematic adjustment of the model constants in the standard k‐ε model using the QUICK. The physical significance of the model constants accounted for changes of the eddy viscosity, and the production and destruction of k and ε.

More industrial cases could benefit from this simple and useful approach.

The constant adjustment is regular and directed, based on the eddy viscosity and the production and destruction of k and ε. The regularity of the effect of the model constants on the solutions makes it easier to quickly adjust them for other industrial applications.