Search results
1 – 10 of 60Jianhua Su, Rui Li, Hong Qiao, Jing Xu, Qinglin Ai and Jiankang Zhu
The purpose of this paper is to develop a dual peg-in-hole insertion strategy. Dual peg-in-hole insertion is the most common task in manufacturing. Most of the previous work…
Abstract
Purpose
The purpose of this paper is to develop a dual peg-in-hole insertion strategy. Dual peg-in-hole insertion is the most common task in manufacturing. Most of the previous work develop the insertion strategy in a two- or three-dimensional space, in which they suppose the initial yaw angle is zero and only concern the roll and pitch angles. However, in some case, the yaw angle could not be ignored due to the pose uncertainty of the peg on the gripper. Therefore, there is a need to design the insertion strategy in a higher-dimensional configuration space.
Design/methodology/approach
In this paper, the authors handle the insertion problem by converting it into several sub-problems based on the attractive region formed by the constraints. The existence of the attractive region in the high-dimensional configuration space is first discussed. Then, the construction of the high-dimensional attractive region with its sub-attractive region in the low-dimensional space is proposed. Therefore, the robotic insertion strategy can be designed in the subspace to eliminate some uncertainties between the dual pegs and dual holes.
Findings
Dual peg-in-hole insertion is realized without using of force sensors. The proposed strategy is also used to demonstrate the precision dual peg-in-hole insertion, where the clearance between the dual-peg and dual-hole is about 0.02 mm.
Practical implications
The sensor-less insertion strategy will not increase the cost of the assembly system and also can be used in the dual peg-in-hole insertion.
Originality/value
The theoretical and experimental analyses for dual peg-in-hole insertion are proposed without using of force sensor.
Details
Keywords
Nagarajan Pitchandi, Saravana Perumaal Subramanian and Muhilan Irulappan
This paper aims to estimate the required insertion force and to analyze the influence of damping in a compliantly supported chamfered peg-in-hole assembly under dynamic conditions.
Abstract
Purpose
This paper aims to estimate the required insertion force and to analyze the influence of damping in a compliantly supported chamfered peg-in-hole assembly under dynamic conditions.
Design/methodology/approach
A mathematical model of the insertion process, including damping coefficient and stiffness of the compliance, insertion speed, mass, inertia and friction coefficient, has been developed. Computer aided design (CAD) model of the peg-in-hole assembly environment with passive compliance is created. The dynamic insertion force of the modeled environment is analyzed using multibody dynamics numerical solver.
Findings
The damping property of the viscoelastic materials used in the passive compliances suppresses the vibration caused due to the impulses in the transition of the peg in hole. It also increases the insertion force required for the peg insertion at the initial stage.
Research limitations/implications
As the search strategies are not considered in this work, it is assumed that the initial contact is ensured between the chamfer and the peg of the assembly. A constant insertion speed is maintained throughout the insertion. Otherwise, it could have been varied at different stages of the insertion for reducing the assembly time.
Practical implications
The developed assembly model can be used for predicting the insertion forces of a chamfered peg-in-hole assembly and for designing/selecting the compliance device for the required assembly environment.
Originality/value
The proposed insertion model has considered the damping and elastic property of the compliance material as a parallel arrangement of spring and dashpot. This approach aids in modeling an insertion process closer to real-time assembly process.
Details
Keywords
Hongtai Cheng, Tianzhuo Liu, Wei Zhang and Lina Hao
Installing a tight tolerant stepped shaft is not a trivial task for an industrial robot. If all peg-hole constraints are complete, the cascaded peg-in-hole task can be simplified…
Abstract
Purpose
Installing a tight tolerant stepped shaft is not a trivial task for an industrial robot. If all peg-hole constraints are complete, the cascaded peg-in-hole task can be simplified into several independent stages and accomplished one by one. However, if some of the constraints are incomplete, the cross stage interference will bring additional difficulties. This paper aims to discuss the cascaded peg-in-hole problem with incomplete constraints.
Design/methodology/approach
In this paper, the problem is formulated according to geometric parameters of the stepped shaft and completeness of the corresponding hole. The possible jamming type is modeled and analyzed. A contact modeling and control strategy is proposed to compensate the peg postures under incomplete constraints.
Findings
The above methods are implemented on an experiment platform and the results verify the effectiveness of the proposed robotic assembly strategy.
Originality/value
Based on force/torque sensor, a hybrid control strategy for incomplete constraints cascaded peg-in-hole assembly problem is proposed.
Details
Keywords
Sigitas Kilikevicius and Bronius Baksys
The paper aims to investigate theoretically and experimentally the process of compliantly supported peg insertion into a bush for high‐speed assembly, when vibrations are provided…
Abstract
Purpose
The paper aims to investigate theoretically and experimentally the process of compliantly supported peg insertion into a bush for high‐speed assembly, when vibrations are provided to the bush in the axial direction, and to analyse the influence of the parameters of the dynamic system and excitation on the assembly process.
Design/methodology/approach
The mathematical model of parts vibratory insertion process is formed and the simulation is performed using a numerical computing software environment. The model includes inertia, compliance, dry friction, insertion speed and vibratory excitation. The three‐dimensional simulation of peg‐in‐hole insertion is accomplished using motion analysis software to test the influence of vibratory excitation on assembly failures, such as jamming and wedging. The experimental setup for the robotic vibratory assembly and the investigation methodology were presented. The experimental analysis of the vibratory insertion process of cylindrical parts with clearance is performed when the compliantly supported peg is inserted by the robot into the bush, which is excited in the axial direction.
Findings
The vibratory excitation allows preventing the balance between the insertion force and frictional forces and so to avoid jamming and wedging. It is advantageous to select such the frequency of vibrations under which the resonance state of the compliantly supported peg does not occur. The parameters of vibratory excitation and initial assembly state are defined which have the principal influence on the insertion duration and the success of the process. The experimental results show the applicability of the mathematical approach.
Research limitations/implications
The assumption is made that the chamferless rigid peg moves in a plane in respect of the rigid bush with a chamfer. Also, it is considered that there is no impact during the peg and bush contact. The dynamic and static friction coefficient between the parts is equivalent and the insertion speed is constant.
Practical implications
The results can be useful aiming to design the reliable high‐performance vibratory assembly equipment for peg‐hole type parts, which does not require sensors, feedback systems and control algorithms.
Originality/value
The proposed method of applying the vibratory excitation during the peg‐in‐hole insertion process allows to avoid jamming and wedging, and to minimize the duration of the process.
Details
Keywords
H.Y.K. Lau and I.S.K. Lee
A neural network controller is proposed for the motion control of robot manipulators with force/torque feedback signals. This controller is trained with reinforcement learning…
Abstract
A neural network controller is proposed for the motion control of robot manipulators with force/torque feedback signals. This controller is trained with reinforcement learning algorithms and a model is extracted from the synaptic weights within the neural network. This model is continuously refined by the feedback signals to ensure its validity even in a stochastic and non‐stationary environment. With this model and the real‐time force/torque feedback data, the robot can acquire a fine skill for a particular assembly task for which it is trained.
Ya'nan Lou, Pengkun Quan, Haoyu Lin, Zhuo Liang, Dongbo Wei and Shichun Di
This purpose of this paper is to design a peg-in-hole controller for a cable-driven serial robot with compliant wrist (CDSR-CW) using cable tensions and joint positions. The peg…
Abstract
Purpose
This purpose of this paper is to design a peg-in-hole controller for a cable-driven serial robot with compliant wrist (CDSR-CW) using cable tensions and joint positions. The peg is connected to the robot link through a CW. It is required that the controller does not rely on any external sensors such as 6-axis wrist force/torque (F/T) sensor, and only the compliance matrix’s estimated value of the CW is known.
Design/methodology/approach
First, the peg-in-hole assembly system based on a CDSR-CW is analyzed. Second, a characterization algorithm using micro cable tensions and joint positions to express the elastic F/T at the CW is established. Next, under the premise of only knowing the compliance matrix’s estimate, a peg-in-hole controller based on force/position hybrid control is proposed.
Findings
The experiment results show that the plug contact F/T can be tracked well. This verifies the validity and correctness of the characterization algorithm and peg-in-hole controller for CDSR-CWs in this paper.
Originality/value
First, to the authors’ knowledge, there is no relevant work about the peg-in-hole assembly task using a CDSR-CW. Besides, the proposed characterization algorithm for the elastic F/T makes the peg-in-hole controller get rid of the dependence on the F/T sensor, which expands the application scenarios of the peg-in-hole controller. Finally, the controller does not require an accurate compliance matrix, which also increases its applicability.
Details
Keywords
Kamal Sharma, Varsha Shirwalkar and Prabir K. Pal
This paper aims to provide a solution to the first phase of a force-controlled circular Peg-In-Hole assembly using an industrial robot. The paper suggests motion planning of the…
Abstract
Purpose
This paper aims to provide a solution to the first phase of a force-controlled circular Peg-In-Hole assembly using an industrial robot. The paper suggests motion planning of the robot’s end-effector so as to perform Peg-In-Hole search with minimum a priori information of the working environment.
Design/methodology/approach
The paper models Peg-In-Hole search problem as a problem of finding the minima in depth profile for a particular assembly. Thereafter, various optimization techniques are used to guide the robot to locate minima and complete the hole search. This approach is inspired by a human’s approach of searching a hole by moving peg in various directions so as to search a point of maximum insertion which is same as the minima in depth profile.
Findings
The usage of optimization techniques for hole search allows the robot to work with minimum a priori information of the working environment. Also, the iterative nature of the techniques adapts to any disturbance during assembly.
Practical implications
The techniques discussed here are quite useful if a force-controlled assembly needs to be performed in a highly unknown environment and also when the assembly setup can get disturbed in between.
Originality/value
The concept is original and provides a non-conventional use of optimization techniques, not for optimization of some process directly but for an industrial robot’s motion planning.
Details
Keywords
Kuangen Zhang, MinHui Shi, Jing Xu, Feng Liu and Ken Chen
This paper aims to realize the automatic assembly process for multiple rigid peg-in-hole components.
Abstract
Purpose
This paper aims to realize the automatic assembly process for multiple rigid peg-in-hole components.
Design/methodology/approach
This paper develops fuzzy force control strategies for the rigid dual peg-in-hole assembly. Firstly the fuzzy force control strategies are presented. Secondly the contact states and contact forces are analyzed to prove the availability of the force control strategies.
Findings
The rigid dual peg-in-hole assembly experimental results show the effectiveness of the control strategies.
Originality/value
This paper proposes fuzzy force control strategies for a rigid dual peg-in-hole assembly task.
Details
Keywords
Jianhua Su, Hong Qiao, Zhicai Ou and Yuren Zhang
The purpose of this paper is to give a novel sensor‐less manipulation strategy for the high‐precision assembly of an eccentric peg into a hole.
Abstract
Purpose
The purpose of this paper is to give a novel sensor‐less manipulation strategy for the high‐precision assembly of an eccentric peg into a hole.
Design/methodology/approach
Based on the authors' previous work on the attractive region, this paper proposes the sensorless eccentric peg‐hole insertion strategy. The analysis is based on the visible strategic behaviors by decomposing the high‐dimensional configuration space of the eccentric peg‐hole into two low dimensional configuration subspaces. Then, the robotic manipulations can be designed in the configuration subspaces. Finally, a typical industry application, fitting an eccentric crankshaft into a bearing hole of the automotive air‐conditioners, is used to validate the presented strategy.
Findings
The attractive region constructed in the configuration space has been applied to guide the robotic manipulations, such as, the locating and the insertion.
Practical implications
The designed robotic assembly system without using force sensor or flexible wrist has an advantage in terms of expense and durability for the automotive air‐conditioners manufacturing industry.
Originality/value
Most previous work on sensorless manipulation strategy has concentrated on inserting a symmetric peg into a hole. However, for the assembly of an eccentric peg into a hole, the robotic manipulations should be explored in a high‐dimensional configuration space as the six‐DOFs of the eccentric peg. In this paper, the decomposition method of the high‐dimensional configuration space would make the system analysis visible; then, the assembly strategy can be easily designed in the two subspaces.
Details
Keywords
Abstract
Purpose
The paper aims to propose a method to build environmental constraint region online in complex-shaped peg-in-hole assembly tasks.
Design/methodology/approach
Compared with conventional way which using computer-aided design (CAD) models of assembly parts to construct the environmental constraint region offline, the paper provides an online approach that consists of three aspects: modeling assembly parts through visual recognition, decomposing complex shapes into multiple primitive convex shapes and a numerical algorithm to simulate the peg-in-hole insertion contact. Besides, a contrast experiment is performed to validate the feasibility and effectiveness of the method.
Findings
The experiment result indicates that online construction takes less time than the offline way under the same task conditions. Furthermore, due to the CAD models of the parts are not required to be known, the method proposed in the paper has a broader application in most assembly scenarios.
Originality/value
With the improvement of customization and complexity of manufactured parts, the assembly of complex-shaped parts has drawn greater attention of many researchers. The assembly methods based on attractive region in environment (ARIE) have shown great performance to achieve high-precision manipulation with low-precision systems. The construction of environmental constraint region serves as an essential part of ARIE-based theory, directly affect the formulation and application of assembly strategies.
Details