Search results

This study aims to establish a friction coefficient model relative to the rotation speed of a wet clutch engagement, which can predict friction coefficient under different stages of slipping velocity and different load pressures. In particular, the model has been improved by accounting the speed effect for the perdition of wet friction-element boundary friction, which is significant for understanding the friction mechanisms and for supporting the development of more efficient and related products.

This research investigated the mechanism of wet friction in a wet clutch engagement. A mixed friction model is established based on the asperity model and Newton’s law of viscosity. To obtain a friction coefficient computed by the model, the normal load shared by both asperities and lubrication fluid needs to be determined. Therefore, rough surface contact mechanism is analysed; a surface topography model is established; and surface parameters are obtained by means of surface topography measurement and reconstruction. Finally, verification of the mixed friction model is achieved.

Friction will be generated by both the asperity contact and the lubrication film shear relative to the rotation speed. And, the higher the relative speed, the larger the shearing power of lubrication film. It is caused by decrease in contact area of asperity. Surface morphology of a sintered bronze friction disk was obtained by a Laser-Micro-Test. The predicted results by the established model show that the total friction coefficient slightly reduced and then increased suddenly with speed. The surface topography model is responsible for the nonlinear behaviour of the asperity friction. Results of the simulation model are in agreement with those of the wet clutch engagement experiments.

This research is original and it is supported by the national defence project. The wet friction element which is applied on tracked vehicles is analysed for the first time. Through the model, the trend of the friction coefficient can be more accurately predicted. The problem of the wet friction plate modelling difficult is solved by using the mixed friction model.

The purpose of this paper is to improve the environment and save energy, friction reduction, lower oil consumption and emissions demand that are the chief objectives of the automotive industry. The piston system is the largest frictional loss source, which accounts for about 40 per cent of the total frictional loss in engine. In this paper, the reciprocating tribometer, which is updated, was used to evaluate the friction and wear performances.

An alternate method is introduced to investigate the effect of reciprocating speed, normal load, oil pump speed and ring sample and oil temperature on friction coefficient with the ring/liner of a typical inline diesel engine. The orthogonal experiment is designed to identify the factors that dominate wear behavior. To understand the correlations between friction coefficients and wear well, different friction coefficient results were compared and explained by oil film build-up and asperity contact theory, such as the friction coefficient over a long period and averaged the friction coefficient over one revolution.

The friction coefficient changes little but fluctuates with a small amplitude in the stable stage. The sudden change of frequency, load and stroke will lead to the oil film rupture. The identification for the factors that dominates the wear loss is ranged as F (ring sample) > , E (oil sample) > , B (stroke) > , D (temperature) > , A (load) > , G (liner) > and C (frequency).

This paper develops and verifies a methodology capable of mimicking the real engine behavior at boundary and mixed lubrication regimes which can minimize frictional losses, wear, reduce much work for the experiment and reduce the cost. The originality of the work is well qualified, as very few papers on a similar analysis have been published, such as: The friction coefficient values fluctuating in the whole stage may be caused by the vibration of the system; suddenly, boundary alternation may help the oil film to form the lubrication; and weight loss mainly comes from the contribution of the friction coefficient value fluctuation. The paper also found that the statistics can gain more information from less experiment time based on a design of experiment.

As the crucial support component of the propeller power system, the reliability of the operation of submersible pumps is influenced by the lubrication performance of water-lubricated thrust bearings. When the water-lubricated thrust bearings are under start-stop or heavy load conditions, the effect of surface morphology is crucial as the mixed lubrication regime is encountered. This paper aims to develop one mixed lubrication model for the water-lubricated thrust bearings to predict the effects of surface skewness, kurtosis and roughness orientation on the loading carrying capacity and tribological behavior.

This paper developed one improved mixed lubrication model specifically for the water-lubricated thrust bearing system. In this model, the hydrodynamic model was improved by using the height of the rough surface and its probability density function, combined with the average flow model. The asperity contact model was improved by using the equation for the Pearson system of frequency curves to characterize the non-Gaussian aspect of surface roughness distribution.

According to the results, negative skewness, large kurtosis and lateral surface pattern can improve the tribological performance of water-lubricated thrust bearings. Optimizing the surface morphology is a reasonable design method that can improve the performance of water-lubricated thrust bearings.

In this paper, one mixed lubrication model specifically for the water-lubricated thrust bearing with the effect of surface roughness into consideration was developed. Based on the developed model, the effect of surface morphology on tribological behavior can be evaluated.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2023-0247/

The purpose of this paper is to study the influence of friction coefficient of materials with different elastic modulus on the variation of velocity and load under water lubrication and oil lubrication conditions.

Low-viscosity lubricating oil and water were used as lubricants to test the friction performance of the ball-disc contact friction pair in the lubrication state on the universal micro-tribometer multi-functional friction and wear test system.

In the same speed range, the lubrication states from soft to rigid materials are not necessarily similar to each other. Generally, the material with low elastic modulus is suitable in low-viscosity lubricant environments, while the material with high elastic modulus has relatively smaller friction coefficients in oil-lubricated environments compared with water lubrication. However, the coefficients of polyethylene, polytetrafluoroethylen and polyoxymethylene are exceeded by rubber’s coefficients under water lubrication in the same experiment environments, and their lubrication states are not affected by lubricants. The friction coefficient of the friction pair decreases with the increase of loads; however, it does not apply to all materials. The friction coefficients of materials with smaller elastic modulus such as rubber under high loads are rather large. Therefore, the elastic modulus of the material under high loads is a factor to be considered.

The Stribeck curves study of the ball-disk contact friction pair comprising soft and rigid materials, whose elastic modulus is from hundreds of GPa to a few of MPa, was carried out. The influence of different speeds, loads and lubricants on the friction coefficient of the friction pair was revealed, which provided a research basis for the selection and matching of friction pair materials.

A free-piston engine (FPE) is an unconventional engine that abandons the crank system. This paper aims to focus on a numerical simulation for the lubricating characteristics of piston rings in a single-piston hydraulic free-piston engine (HFPE).

A time-based numerical simulation program was built using Matlab to define the piston motion of the new engine. And a lubrication mode of piston rings was built which is based on the gas flow equation, hydrodynamic lubrication equation and the asperity contact equation. The piston motion and the lubrication model are coupled, and then the finite difference method is used to obtain the piston rings lubrication performances of the FPE. Meanwhile, the lubrication characteristics of the new engine were compared with those of a corresponding conventional crankshaft-driven engine.

The study results indicate that compared with the traditional engine, the expansion stroke of the HFPE is longer, and the compression stroke is shorter. Lubrication oil film of the new engine is thicker than the traditional engine during the initial stage of compression stroke and the final stage of the power stroke. The average friction force and power of the hydraulic free piston engine are slightly lower than those of the traditional engine, but the peak friction power of the FPE is significantly greater than that of the traditional engine. With an increase in load, the friction loss power and friction loss efficiency decrease, and with a decrease in equivalence ratio, the friction power loss reduces, but the friction loss efficiency decreases first and then increases.

In this paper, only qualitative analysis was performed on the tribological difference between conventional crankshaft engine and HFPE, instead of a quantitative one.

This paper contributes to the tribological design method of HFPE.

No social implications are available now, as the HFPE is under the development phase. However, the authors are positive that their work will be commercialized in the near future.

The main originality of the paper can be introduced as follows: the lubrication and friction characteristics of the new engine (HFPE) were investigated and revealed, which have not been studied before; the effect of the HFPE’s special piston motion on the tribological characteristics was considered in the lubrication simulation. The results show that compared with the traditional crankshaft engine, the new engine shows a different lubrication performance because of its free piston motion.

Piston ring dynamic problem plays an important role in the lubricant characteristics of a reciprocating engine, which lead to engine wear and the increased consumption of lubricating oil. A cavitation analysis of the piston ring lubrication with two-dimensional Reynolds equation has rarely been reported owing to the complex working condition. The purpose of this study is to establish a precise model that can provide guidance for the design of the piston ring.

In this paper, a cavitation model and its effect on the piston ring lubrication was studied in a simulation program based on the mass-conserving theory which is solved by means of the Newton–Raphson method. In this study, some models such as mixed lubrication, asperity contact, blow-by/blow-back flow and cavitation have been coupled with the lubrication model.

The established model has been compared with the traditional model that deals with cavitation by using the Reynolds boundary condition algorithm. The cavitation zone, pressure distribution and density distribution between the piston ring and the cylinder have also been predicted. Studies of the changing trend for the pressure distribution and the cavitation zone at few typical crank angles have been listed to illustrate the cavitation changing rule. The analysis of the results indicates that the developed simulation model can adequately illustrate the lubrication problem of the piston ring system. All the analyses will provide guidance for the oil film rupture and the reformation process.

A two-dimensional cavitation model based on the mass-conserving theory has been built. The cavitation-forming and -developing process for the piston ring–liner lubrication has been studied. Non-cavitation occurs in the vicinity of top dead center and bottom dead center. The non-cavitation period will be longer in the vicinity of 360° of crank angle. The density distribution in the cavitation zone can be obtained.

A study of piston ring‐cylinder tribological behaviour under mixed lubrication mode is usually based upon data regarding surface contact magnitudes, fluid film characteristics and resultant mixed friction forces. The present paper introduces a Fisher‐Pearson statistical model to describe elastic deformation of piston rings and liners’ asperities in order to derive more realistic functions that represent the aforementioned functional quantities considering real surfaces of used and worn liners. The hypothesis that the microtopography follows Gaussian law overestimates critical contact magnitudes such as: minimum film thickness‐surface separation distance, deformed asperities supported load, number of contacts and contact area. Increased time of use and wear of liners decreases transverse geometrical anisotropy. Correction contact integral functions in cases of used liners’ surfaces may be calculated through surface profile measurements. Theoretical and experimental results are in good agreement for the configuration considered.

This study aims to investigate the effects of irregular groove textures on the friction and wear performance of sliding contact surfaces. These textures possess multiple depths and asymmetrical features. To optimize the irregular groove texture structure of the sliding contact surface, an adaptive genetic algorithm was used for research and optimization purposes.

Using adaptive genetic algorithm as an optimization tool, numerical simulations were conducted on surface textures by establishing a dimensionless form of the Reynolds equation and setting appropriate boundary conditions. An adaptive genetic algorithm program in MATLAB was established. Genetic iterative methods were used to calculate the optimal texture structure. Genetic individuals were selected through fitness comparison. The depth of the groove texture is gradually adjusted through genetic crossover, mutation, and mutation operations. The optimal groove structure was ultimately obtained by comparing the bearing capacity and pressure of different generations of micro-convex bodies.

After about 100 generations of iteration, the distribution of grooved textures became relatively stable, and after about 320 generations, the depth and distribution of groove textures reached their optimal structure. At this stage, irregular texture structures can support more loads by forming oil films. Compared with regular textures, the friction coefficient of irregular textures decreased by nearly 47.01%, while the carrying capacity of lubricating oil films increased by 54.57%. The research results show that irregular texture structures have better lubrication characteristics and can effectively improve the friction performance of component surfaces.

Surface textures can enhance the friction and lubrication performance of metal surfaces, improving the mechanical performance and lifespan of components. However, surface texture processing is challenging, as it often requires multiple experimental comparisons to determine the optimal texture structure, resulting in high trial-and-error costs. By using an adaptive genetic algorithm as an optimization tool, the optimal surface groove structure can be obtained through simulation and modeling, effectively saving costs in the process.

Cavitation in piston-ring lubrication is studied as part of the performance of piston-ring assemblies. Cavitation degrades performance in engineering applications and its effect is that it alters the oil film pressure, generated at the converging-diverging wedge of the interface. Studies tried to shed light to the phenomenon of cavitation and compare it with cavities that have been identified in bearings. The paper aims to discuss this issue.

Lubricant formulations were used for parametric study of oil film thickness (OFT) and friction providing the OFT throughout the stroke and LIF for OFT point measurements. Lubricant formulation affects cavitation appearance and behaviour when fully developed.

Cavitation affects the ring load carrying capacity. Different forms of cavitation were identified and their shape and size (length and width) is dictated from reciprocating speed and viscosity of the lubricant. A clear picture is given from both techniques and friction results give quantifiable data in terms of the effect in wear and cavitation, depending on the lubricant properties.

Engine results are limited due to manufacturing difficulties of visualisation windows and oil starvation. Therefore, full stroke length sized windows were not an option and motoring tests were implemented due to materials limitations (adhesive and quartz windows). Lubricant manufacturer has to give data regarding the chemistry of the lubricants.

The contribution of cavitation in piston-ring lubrication OFT, friction measurements and lubricant parameters that try to shed light to the different forms of cavitation. A link between viscosity, cavitation, shear thinning properties, OFT and friction is given.

Running-in is a transient process prior to steady state and of great importance for mechanical performance. To reveal the fractal behavior in the running-in process, the steel-on-steel friction and wear tests were performed.

The friction coefficient, friction temperature, friction noise and vibration were recorded, and the surface profile of lower sample was measured on line. The signals and profiles were characterized by correlation dimension and box-counting dimension, respectively.

The signals have the consistent fractal evolvement law, that is, the correlation dimension increases and tends to a stable value. The box-counting dimension of one surface becomes close to that of the other surface. The running-in process can be interpreted as a process in which the fractal dimension of friction signals increases, and the counter surfaces spontaneously adapt to and modify each other to form a spatial ordered structure.

The results reveal the running-in behavior from a new perspective.