Search results

This paper aims to introduce a novel method for the analysis of open cell porous components fabricated by laser-based powder bed metal additive manufacturing (AM) for the purpose of quality control. This method uses photogrammetric analysis, the extraction of geometric information from an image through the use of algorithms. By applying this technique to porous AM components, a rapid, low-cost inspection of geometric properties such as material thickness and pore size is achieved. Such measurements take on greater importance, as the production of porous additive manufactured orthopaedic devices increases in number, causing other, slower and more expensive methods of analysis to become impractical.

Here the development of the photogrammetric method is discussed and compared to standard techniques including scanning electron microscopy, micro computed tomography scanning and the recently developed focus variation (FV) imaging. The system is also validated against test graticules and simple wire geometries of known size, prior to the more complex orthopaedic structures.

The photogrammetric method shows an ability to analyse the variability in build fidelity of AM porous structures for use in inspection purposes to compare component properties. While measured values for material thickness and pore size differed from those of other techniques, the new photogrammetric technique demonstrated a low deviation when repeating measurements, and was able to analyse components at a much faster rate and lower cost than the competing systems, with less requirement for specific expertise or training.

The advantages demonstrated by the image-based technique described indicate the system to be suitable for implementation as a means of in-line process control for quality and inspection applications, particularly for high-volume production where existing methods would be impractical.

Process parameters in Fused Filament Fabrication (FFF) can affect mechanical and surface properties of printed parts. Numerous studies have reported parametric studies of various materials using full factorial and Taguchi design of experiments (DoEs). However, a comparison between the two are not well-established in literature. The purpose of this study is to compare full factorial and Taguchi DoEs to determine the effects of FFF process parameters on mechanical and surface properties of Nylon 6/66 copolymer. In addition, perform in-depth failure mechanism analysis to understand why the process parameters affect the responses.

A full factorial DoE was used to determine the effects of FFF process parameters, such as infill density, infill pattern, layer height and raster angle on responses, such as compressive strength, impact strength, surface roughness and manufacturing time of Nylon 6/66. Micro-computed tomography was used to analyse the impact test samples before and after impact and scanning electron microscope was used to understand the failure mechanism of infill and top layers. Differential scanning calorimetry (DSC) scans of infill and top layers were then taken to determine if a variation in crystallinity existed in different regions of the build.

Analysis of variance and main effects plots reveal that infill density has the greatest effect on mechanical and surface properties while manufacturing time is most affected by layer height for the polymer used. A 20% reduction in infill increased impact strength by 19% on average, X-ray images of some of the samples before and after impact tests are presented to understand the reason behind the difference. Moreover, DSC revealed a difference in the degree of crystallinity between the infill and top layers for 80% infill density samples. In addition, Taguchi DoE is realized to be a more efficient technique to determine optimum process parameters for responses that vary linearly as it reduces experimental effort significantly while providing mostly accurate results.

To the author’s knowledge, no published paper has reported a comparison between predictive DoE method with full factorial DoE to verify their accuracy in determining the effects of FFF process parameters on properties of printed parts. Also, a theory was developed based on DSC results that as the infill is printed faster, it cools slowly compared to the top layers, and hence the infill is in a less crystalline state when compared to the top layers. This increased the ductility of the infill (of 80% infill samples) and thus improved impact absorption.

The purpose of this paper is to establish a methodology for the design and development of patient-specific elbow implant with an elastic modulus close to that of the human bone. One of the most preferred implant material is titanium alloy which is about 8 to 9 times higher in strength than that of the human bone and is the closest than other metallic biomedical materials.

The methodology begins with the design of the implant from patient-specific computed tomography information and incorporates the manufacturing of the implant via a novel rapid prototyping assisted microwave sintering process.

The elastic modulus and the flexural strength of the implant were observed to be comparable to that of human elbow bones. The fatigue test depicts that the implant survives the one million cycles under physiological loading conditions. Other mechanical properties such as impact energy absorption, hardness and life cycle tests were also evaluated. The implant surface promotes human cell growth and adhesion and does not cause any adverse or undesired effects i.e. no cytotoxicity.

Stress shielding, and therefore, aseptic loosening of the implant shall be avoided. In the event of any trauma post-implantation, the implant would not hurt the patient.

The present study describes a methodology for the first time to be able to obtain the strength required for the medical implant without sacrificing the fatigue life requirement.

The purpose of this paper is to understand the relationship between defect properties and the tool path used for generating additively manufactured parts. The correlation between processing strategy and porosity architecture is one of the key aspects for a precise understanding of defect formation and possibilities for defect reduction.

The authors present a new combined geometry, processing path and porosity analysis procedure based on the use of x-ray computed micro tomography image data and numerical control programming code. The procedure allows for a covisualisation of the track of the respective processing head with the three-dimensional microstructure data.

The presented method yields statistical results about defect distribution and morphologies introduced by the respective process characteristics in parts. The functionality of the proposed procedure is demonstrated on an aluminum (AlSi10Mg) and a polylactide test sample to show the additional insight found for both additive manufacturing processes and the resulting microstructural properties.

The novelty of this paper is the analysis of the porosity with respect to the underlying additive process zone and the sample geometry.

Additive manufacturing (AM), a rapidly evolving paradigm, has shown significant advantages over traditional subtractive processing routines by allowing for the custom creation of structural components with enhanced performance. Numerous studies have shown that the technical qualities of AM components are profoundly affected by the discovery of novel metastable substructures in diverse alloys. Therefore, the purpose of this study is to determine the effect of cell structure parameters on its mechanical response.

Initially, a methodology was suggested for testing porous materials, focusing on static tensile testing. For a qualitative evaluation of the cellular structures produced, computed tomography (CT) was used. Then, the CT scanner was used to analyze a sample and determine its actual relative density, as well as perform a detailed geometric analysis.

The experimental research demonstrates that the mechanical properties of a cell’s structure are significantly influenced by its shape during formation. It was also determined that using selective laser melting to produce cell structures with a minimum single-cell size of approximately 2 mm would be the most appropriate method.

Further studies of cellular structures for testing their static tensile strength are planned for the future. The study will be carried out for a larger number of samples, taking into account a wider range of cellular structure parameters. An important step will also be the verification of the results of the static tensile test using numerical analysis for the model obtained by CT scanning.

The fabrication of metallic parts with different cellular structures is very important with a selective laser melted machine. However, the determination of cell size and structure with mechanical properties is quiet novel in this current investigation.

The purpose of this paper is to investigate the influence of a process interruption on the tensile properties of AlSi10Mg samples produced by selective laser melting (SLM).

Using identical processing parameters, cylindrical samples were produced in either a continuous or interrupted SLM build operation. The tensile properties and microstructure of the samples were determined as a function of process type as well as orientation.

All samples produced in this paper displayed superior tensile properties to those produced in high pressure die casting. In general, the samples produced in the continuous build process had higher strengths and microhardness than those produced in the interrupted process. However, while most samples displayed random failure locations, the vertical samples produced in the interrupted build process showed a strong tendency for localized failure in the vicinity of the stoppage plane.

This paper demonstrated that samples produced in an interrupted build process tend to have poorer mechanical properties than those produced in a continuous process. Together, these observations highlight the importance of a suitable technique for restarting and completing an interrupted build process to ensure the production of high quality components.

The purpose of this paper is to outline some key aspects such as material systems used, phenomenological and statistical process modeling, techniques applied to monitor the process and optimization approaches reported. All these need to be taken into account for the ongoing development of the SLM technique, particularly in health care applications. The outcomes from this review allow not only to summarize the main features of the process but also to collect a considerable amount of investigation effort so far achieved by the researcher community.

This paper reviews four significant areas of the selective laser melting (SLM) process of metallic systems within the scope of medical devices as follows: established and novel materials used, process modeling, process tracking and quality evaluation, and finally, the attempts for optimizing some process features such as surface roughness, porosity and mechanical properties. All the consulted literature has been highly detailed and discussed to understand the current and existing research gaps.

With this review, there is a prevailing need for further investigation on copper alloys, particularly when conformal cooling, antibacterial and antiviral properties are sought after. Moreover, artificial intelligence techniques for modeling and optimizing the SLM process parameters are still at a poor application level in this field. Furthermore, plenty of research work needs to be done to improve the existent online monitoring techniques.

This review is limited only to the materials, models, monitoring methods, and optimization approaches reported on the SLM process for metallic systems, particularly those found in the health care arena.

SLM is a widely used metal additive manufacturing process due to the possibility of elaborating complex and customized tridimensional parts or components. It is corroborated that SLM produces minimal amounts of waste and enables optimal designs that allow considerable environmental advantages and promotes sustainability.

The key perspectives about the applications of novel materials in the field of medicine are proposed.

The investigations about SLM contain an increasing amount of knowledge, motivated by the growing interest of the scientific community in this relatively young manufacturing process. This study can be seen as a compilation of relevant researches and findings in the field of the metal printing process.

The results showed that the use of a magnetic marker could relatively accurately reflect the fracture pattern inside the rock-like material (RLM).

This study investigated the internal structure and fracture pattern of a fractured RLM. Magnetized iron oxide powder, which was used as a magnetic marker, was mixed with water and glue to form a magnetic slurry, which was subsequently injected into a fractured RLM. After the magnetic slurry completely filled the cracks inside the RLM and became cemented, the distribution and magnitude of the magnetic field inside the RLM were determined using a three-dimensional (3D) magnetic field imaging system.

A model for determining the magnetic field strength was developed using MATLAB.

This model of 3D magnetic will further be used as a finite element tool to simulate and image cracks inside the rock.