Search results

For metal additive manufacturing, metallic powders are usually produced by vacuum induction gas atomization (VIGA) through the breakup of liquid metal into tiny droplets by gas jets. VIGA is considered a cost-effective technique to prepare feedstock. In VIGA, the quality and the morphology of the produced particles are mainly controlled by the gas pressure used during powder production, keeping the setup configuration constant.

In VIGA process for metallic additive manufacturing feedstock preparation, the quality and morphology of the powder particles are mainly controlled by the gas pressure used during powder production.

In this study, Inconel-625 feedstock was produced using a supersonic nozzle in a close-coupled gas atomization apparatus. Powder size distribution (PSD) was studied by varying the gas pressure.

The nonmonotonic but deterministic relationships were observed between gas pressure and PSD. It was found that the maximum 15–45 µm percentage PSD, equivalent to 84%, was achieved at 29 bar Argon gas pressure, which is suitable for the LPBF process. Following on, the produced powder particles were used to print tensile test specimens via LPBF along XY- and ZX-orientations by using laser power = 475 W, laser scanning speed = 800 mm/s, powder layer thickness = 50 µm and hatch distance = 100 µm. The yield and tensile strengths were 9.45% and 13% higher than the ZX direction, while the samples printed in ZX direction resulted in 26.79% more elongation compared to XY-orientation.

This study aims to describe the effects of capillary forces or action, viscosity, gravity and inertia via the computational fluid dynamics (CFD) analysis. The study also includes distribution of the binder droplet over the powder bed after interacting from different heights.

Additive manufacturing (AM) has revolutionized many industries. Binder jetting (BJT) is a powder-based AM method that enables the production of complex components for a wide range of applications. The pre-densification interaction of binder and powder is vital among various parameters that can affect the BJT performance. In this study, BJT process is studied for the binder interaction with the powder bed of SS316L. The effect of the droplet-powder distance is thoroughly analysed. Two different droplet heights are considered, namely, h1 (zero) and h2 (9.89 mm).

The capillary and inertial effects are predominant, as the distance affects these parameters significantly. The binder spreading and penetration depth onto the powder bed is influenced directly by the distance of the binder droplet. The former increases with an increase in latter. The binder distribution over the powder bed, whether uniform or not, is studied by the stream traces. The penetration depth of the binder was also observed along the cross-section of the powder bed through the same.

In this work, the authors have developed a more accurate representative discrete element method of the powder bed and CFD analysis of binder droplet spreading and penetration inside the powder bed using Flow-3D. Moreover, the importance of the splashing due to the binder’s droplet height is observed. If splashing occurs, it will produce distortion in the powder, resulting in a void in the final part.

This paper aims to reduce part defects and improve ceramic additive manufacturing (AM). Selective laser melting (SLM) experiments were carried out to explore the effect of laser power and scanning speed on the microstructure, melting behaviour and surface roughness of cuprous oxide (Cu₂O) ceramic.

The experiments were designed based on varying laser power and scanning speed. The laser power was changed between 50 W and 140 W, and the scanning speed was changed between 170 mm/s and 210 mm/s. Other parameters, such as scanning strategy, layer thickness and hatch spacing, remain constant.

Laser power and scan speed are the two important laser parameters of great significance in the SLM technique that directly affect the molten state of ceramic powders. The findings reveal that Cu₂O part defects are widely controlled by gradually increasing the laser power to 110 W and reducing the scanning speed to 170 mm/s. Furthermore, excessive laser power (>120 W) caused surface roughness, cavities and porous microstructure due to the extremely high energy input of the laser beam.

The SLM technique was used to produce Cu₂O ceramic specimens. SLM of oxide ceramic became feasible using a slurry-based approach. The causes of several part defects such as spattering effect, crack initiation and propagation, the formation of porous microstructure, surface roughness and asymmetrical grain growth during the SLM of cuprous oxide (Cu₂O) are thoroughly investigated.