Search results

Corporate social responsibility (CSR) ISO standards have been noted as an essential marketing strategy by which firms can achieve consumer trust while improving environmental, social, and quality factors. This study discloses the contextual relationship between CSR ISO standards and sustainable impulse buying behavior. This study also looks to uncover the CSR ISO driving and linkage factors that motivate consumers to make sustainable impulsive purchases.

Three distinct research methods were employed in this research. First, a consumer expert opinion-based Interpretive Structural Modeling (ISM) approach was adopted to reveal the contextual relationship between CSR ISO factors and sustainable impulse buying behavior. Secondly, Matrice Impacts Croises Multiplication Appliques Classement (MICMAC) was used to examine these factors' driving and dependent power. In addition, Minitab package software was also used to check the statistical validation of ISM-MICMAC results.

The results indicate that although environmentally responsible CSR ISO 14001, socially responsible CSR ISO 26000, and consumer perception of product quality CSR ISO 9001 standards contain strong driving power, their dependent power was weak. All these CSR ISO factors (14,001, 26,000, and 9001) strongly impact each other and sustainable impulse buying. Therefore, these three CSR ISO factors have been placed at the bottom of the ISM model. The CSR ISO 14020 standard (labeling of the product), knowledge of CSR ISO standards, consumer trust, and advertising about CSR ISO standards have been placed in the middle. The mentioned factors have intense driving and dependent power and are classified as linkage factors for sustainable impulse buying. Impulse buying behavior has weak driving and strong dependent power, yet this factor strongly depends on other CSR ISO factors. Hence, this factor is placed at the top of the ISM model. In addition, the Minitab package software results indicate that ISM-MICMAC results are statistically valid.

To the best of our knowledge, this research is unique and examines the influence of CSR ISO factors on sustainable impulse buying in the context of Pakistani consumers. Secondly, our study has thoroughly investigated several CSR ISO factors and allied these factors in the context of consumer buying behavior. Third, several CSR ISO factors and impulse buying behavior were examined using a mix of ISM-MICAC and Minitab methods. Thus, including these steps in our study has led to the development of a novel technique.

The use of technology in 4th industrial revolution is at its peak. Industries are trying to reduce the consumption of resources by effectively utilizing information and technology to connect different functioning agents of the manufacturing industry. Without digitization “Industry 4.0” will be a virtual reality. The present survey-based study explores the factual status of digital manufacturing in the Northern India.

After an extensive literature review, a questionnaire was designed to gather different viewpoints of Indian industrial practitioners. The first half contains questions related to north Indian demographic factors which may affect digitalization of India. The latter half includes the queries concerned with various operational factors (or drivers) driving the digital revolution without ignoring Indian constraints.

The focus of this survey was to understand the current level of digital revolution under the ongoing push by the Indian government focused upon digital movement. The analysis included non-parametric testing of the various demographic and functional factors impacting the digital echoes, specifically in Northern India. Findings such as technological upgradations were independent of type of industry, the turnover or the location. About 10 key operational factors were thoughtfully grouped into three major categories—internal Research and Development (R&D), the capability of the supply chain and the capacity to adapt to the market. These factors were then examined to understand how they contribute to digital manufacturing, utilizing an appropriate ordinal logistic regression. The resulting predictive analysis provides seldom-seen insights and valuable suggestions for the most effective deployment of digitalization in Indian industries.

The country-specific Industry 4.0 literature is quite limited. The survey mainly focuses on the National Capital Region. The number of demographic and functional factors can further be incorporated. Moreover, an addition of factors related to ecology, environment and society can make the study more insightful.

The present work provides valuable insights about the current status of digitization and expects to facilitate public or private policymakers to implement digital technologies in India with less efforts and the least resistance. It empowers India towards Industry 4.0 based tools and techniques and creates new socio-economic dimensions for the sustainable development.

The quantitative nature of the study and its statistical predictions (data-based) are novel. The clubbing of similar success factors to avoid inter-collinearity and complexity is seldom seen. The predictive analytics provided in this study is quite elusive as it provides directions with logic. It will help the Indian Government and industrial strategists to plan and perform their interventions accordingly.

This study aims to provide a salt ready-mix to instant fried noodles manufacturers.

Response surface methodology was used to get optimized salt ready-mix based on carbonate salt, disodium phosphate, tripotassium phospahte, sodium hexametaphosphate and sodium chloride. Peak viscosity of flour and yellowness, cooking loss and hardness of noodles were considered as response factors for finding optimized salt formulation.

The results showed that salts have an important role in governing quality of noodles. Optimum levels of five independent variables of salts, namely, carbonate salt (1:1 mixture of sodium to potassium carbonate), disodium phosphate, sodium hexametaphosphate, tripotassium phosphate and sodium chloride were 0.64%, 0.29%, 0.25%, 0.46% and 0.78% on flour weight basis, respectively.

To the best of the authors’ knowledge, this is the first study to assess the effect of different combinations of different salts on the quality of noodles. These findings will also benefit noodle manufacturers, assisting in production of superior quality noodles.

There is evidence that quality improvement projects developed with the participation of patients and family members are more likely to result in a sustainable change. To identify the intervening factors is an important step in promoting and supporting patient and family members’ engagement.

A survey was carried out with 90 hospitals. A total of 35 intervening factors were evaluated by the healthcare professionals from the quality area using a Likert scale. Factor analysis was applied to identify the relationship among the factors and cluster analysis and the standardized scores for each new latent variable were obtained to observe the association between them and hospitals profile. Cluster analysis allowed to group the hospitals with similar responses and to analyze whether there was any association with the profile of the institutions.

A total of ten intervening factors are identified: two in the financial dimension, five in the structural and three in the personal and cultural. The standardized scores of latent variables suggest that the financial factors could be affected by the hospital capacity. The structural factors could be impacted by the accreditation status, location (region) and administrative control (ownership). And the personal and cultural factors could be by the location and dominant organizational culture. All of factors are influenced by the performed quality management activities. The cluster analysis allowed the identification of three groups in the financial dimension, and four in the other two dimensions. Except for the accreditation status in the personal and cultural dimension, no evidence of association between the groups and the variables raised to characterize the profile of the hospitals was found.

The study contributed to identify the relationship among the intervening factors turning possible to simplify and reduce them more comprehensively than those originally identified in the literature and at the same time maintaining the representativeness of the original variables.

This study aims to propose the reuse of PA12 (powder) in another AM process, binder jettiinng, which is less sensitive to the chemical and mechanical degradation of the powder after multiple cycles in the laser system.

The experimental process for evaluating the reuse of SLS powders in a subsequent binder jetting process consists of four phases: powder characterization, bonding analysis, mixture testing and mixture characteristics. Analyses were carried out using techniques such as Fourier Transform Infrared Spectroscopy, scanning electron microscopy, thermogravimetric analysis and stress–strain tests for tension and compression. The surface roughness, color, hardness and density of the new mixture were also determined to find physical characteristics. A Taguchi design L8 was used to search for a mixture with the best mechanical strength.

The results indicated that the integration of waste powder PA12 with calcium sulfate hemihydrate (CSH) generates appropriate particle distribution with rounded particles of PA12 that improve powder flowability. The micropores observed with less than 60 µm, facilitated binder and infiltrant penetration on 3D parts. The 60/40 (CSH-PA12) mixture with epoxy resin postprocessing was found to be the best-bonded mixture in mechanical testing, rugosity and hardness results. The new CSH-PA12 mixture resulted lighter and stronger than the CSH powder commonly used in binder jetting technology.

This study adds value to the polymer powder bed fusion process by using its waste in a circular process. The novel reuse of PA12 waste in an established process was achieved in an accessible and economical manner.

This study explores how titanium oxide (TiO₂) filler influences the specific wear rate (SWR) in flax fiber-reinforced epoxy composites (FFRCs) through a Taguchi approach. It aims to boost abrasive wear resistance by incorporating TiO₂ filler, promoting sustainable and eco-friendly materials.

This study fabricates epoxy/flax composites with TiO₂ particles (0–8 wt%) using hand layup. Composites were tested for wear following American Society for Testing and Materials (ASTM) G99-05. Statistical analysis used Taguchi design of experiments (DOE), with ANOVA identifying key factors affecting SWR in abrasive sliding conditions.

The study illuminates how integrating TiO2 filler particles into epoxy/flax composites enhances abrasive wear properties. Statistical analysis of SWR highlights abrasive grit size (grit) as the most influential factor, followed by normal load, wt% of TiO₂ and sliding distance. Grit size has the highest effect at 43.78%, and wt% TiO₂ filler contributes 15.61% to SWR according to ANOVA. Notably, the Taguchi predictive model closely aligns with experimental results, validating its reliability.

This paper integrates TiO₂ filler and flax fibers to form a novel hybrid composite with enhanced tribological properties in epoxy composites. The use of Taguchi DOE and ANOVA offers valuable insights for optimizing control variables, particularly in natural fiber-reinforced composites (NFRCs).

The six-axis force/torque sensor based on a Y-type structure has the advantages of simple structure, small space volume, low cost and wide application prospects. To meet the overall structural stiffness requirements and sensor performance requirements in robot engineering applications, this paper aims to propose a Y-type six-axis force/torque sensor.

The performance indicators such as each component sensitivities and stiffnesses of the sensor were selected as optimization objectives. The multiobjective optimization equations were established. A multiple quadratic response surface in ANSYS Workbench was modeled by using the central composite design experimental method. The optimal manufacturing structural parameters were obtained by using multiobjective genetic algorithm.

The sensor was optimized and the simulation results show that the overload resistance of the sensor is 200%F.S., and the axial stiffness, radial stiffness, bending stiffness and torsional stiffness are 14.981 kN/mm, 16.855 kN/mm, 2.0939 kN m/rad and 6.4432 kN m/rad, respectively, which meet the design requirements, and the sensitivities of each component of the optimized sensor have been well increased to be 2.969, 2.762, 4.010, 2.762, 2.653 and 2.760 times as those of the sensor with initial structural parameters. The sensor prototype with optimized parameters was produced. According to the calibration experiment of the sensor, the maximum Class I and II errors and measurement uncertainty of each force/torque component of the sensor are 1.835%F.S., 1.018%F.S. and 1.606%F.S., respectively. All of them are below the required 2%F.S.

Hence, the conclusion can be drawn that the sensor has excellent comprehensive performance and meets the expected practical engineering requirements.

The application of indigo dyes in the denim industries has been criticised due to the introduction of non-renewable oxidation products into the environment. Previous studies have investigated that reducing sugars can be used as green alternatives to sodium dithionite in the indigo dyeing of cotton fabric owing to their reduced and stable redox potential in the dye bath. The purpose of this study was to dye denim cotton fabric with indigo dye using various reducing sugars and alkalis. The use of sucrose and potassium hydroxide (KOH) for indigo dyeing has been explored for the first time.

A mixed factorial design with four variables including alkali, pH, number of dips and type of reducing sugar at different levels was studied to identify a significant correlation between the effect of these variables on the colour strength and fastness properties of the dyeings.

Investigations were made to examine the significant factors and interactions of the selected responses in the eco-friendly dyeing method. This process has the potential to reduce the load of sulphite and sulphate generated in the dyebath due to the use of a conventional reducing agent, sodium dithionite. The colour strength of the dyeing reduced with fructose was found to be better than other reducing sugars and significantly influenced by the number of dips, pH levels and the interaction between pH and reducing sugars. Using fructose for indigo dyeing with two dips at a pH of 11.5, using KOH as an alkali, results in higher colour strength values. The fastness properties of the indigo-dyed sample with reducing sugars ranging from fair to good or good to excellent. Specifically, colour change receives a rating of grey scale 3–4, staining 4–5, dry rubbing 4 and light fastness 3–4. These assessments hold true across various factors such as the type of reducing sugar, alkali, pH and the number of dips. The optimised parameters leading to improved colour strength and fastness properties are also discussed.

This dyeing technique is novel and a green alternative to dithionite denim dyeing. This process is found to be useful for indigo dyeing of denim fabric leading to reduced and stable redox potential in the dyebath and acceptable colour strength of the dyed fabric.

The purpose of this paper is to examine the mechanical characteristics and optimization of wear parameters of hybrid (TiO₂ + Y₂O₃) nanoparticles with Al matrix using squeeze casting technique.

The hybrid aluminium matrix nanocomposites (HAMNCs) were fabricated with varying concentrations of titanium oxide (TiO₂) and yttrium oxide (Y₂O₃), from 2.5 to 10 Wt.% in 2.5 Wt.% increments. Dry sliding wear test variables were optimized using the Taguchi method.

The introduction of hybrid nanoparticles in the aluminium (Al) matrix was evenly distributed in contrast to the base matrix. HAMNC6 (5 Wt.% TiO₂ + 5 Wt.% Y₂O₃) reported the maximum enhancement in mechanical properties (tensile strength, flexural strength, impact strength and density) and decrease in porosity% and elongation% among other HAMNCs. The results showed that the optimal combination of parameters to achieve the lowest wear rate was A3B3C1, or 15 N load, 1.5 m/s sliding velocity and 200 m sliding distance. The sliding distance showed the greatest effect on the dry sliding wear rate of HAMNC6 followed by applied load and sliding velocity. The fractured surfaces of the tensile sample showed traces of cracking as well as substantial craters with fine dimples and the wear worn surfaces were caused by abrasion, cracks and delamination of HAMNC6.

Squeeze-cast Al-reinforced hybrid (TiO₂+Y₂O₃) nanoparticles have been investigated for their impact on mechanical properties and optimization of wear parameters.

The purpose of this study is to determine the effect of laser treatment on disperse dye-uptake and fastness values of polyester fabrics. Furthermore, it was aimed to evaluate colors directly over the photos of fabric samples instead of color measuring with spectrophotometer which is thought to be useful in terms of online digital color assessment.

In this study, 100% polyester (150 denier) single jersey knitted fabrics (weight: 145 g/m2, course density: 15 loops/cm, wale density: 24 loops/cm) were used in the trials. The effect of laser treatments before and after dyeing on color was investigated. Laser treatments were applied to fabrics at different resolutions (20, 25 and 30 dpi) and pixel times (60, 80 and 100 µs) before dyeing. The power of the laser beam was 210 W and the wavelength was 10.6 µm. In order to determine the effect of laser treatment on polyester; FTIR analysis, SEM-EDX analysis and bursting strength tests were applied to untreated and treated fabric samples.

It was found that treatments with laser have a significant effect on disperse dye-uptake of polyester fibers, and for this reason laser-treated fabrics were dyed in darker shade. Furthermore, it was determined that the samples treated at 30 dpi started to melt and the fabric was damaged considerably, but the fabrics treated at 20 and 25 dpi were not affected at all. Another result obtained regarding the use of laser technology in polyester fabrics is that if some areas of fabrics are not treated with laser and some other areas are treated with laser at 20 dpi 60 µs and 25 dpi 60 µs, it will be possible to obtain patterns containing three different shades of the same color on the fabric.

When the literature is examined, it is seen that there are various studies on the dyeability and patterning of polyester fabrics with disperse dyes by laser technology. As it is known, today color measurement is done digitally using a spectrophotometer. However, when we look at a photograph on computer screens, the colors we see are defined by RGB (red-green-blue) values, while in the spectrophotometer they are defined by L*a*b* (L*: lightness-darkness, a*: redness-greenness, b*: yellowness-blueness) values. Especially when it is desired to produce various design products by creating patterns with laser technology, it would be more useful to show the color directly to the customer on the computer screen and to be able to speak over the same values on the color. For this reason, in this study, the color measurement of the fabric samples was not made with a spectrophotometer, instead, the RGB values obtained from the photographs of the samples were converted into L*a*b* values with MATLAB and interpreted, that is, a digital color evaluation was made on the photographs. Therefore, it is believed that this study will contribute to the literature.