Search results

The purpose of this paper is to quantitatively investigate the effect of process parameters (including welding current, voltage and speed) and plate thickness on in-plane inherent deformations in typical fillet welded joint; meanwhile, the plastic strains remaining in the weld zone are also analyzed under different influencing factors.

To achieve the purpose of this study, a thermal-elastic-plastic finite element (TEP FE) model is developed to analyze the thermal-mechanical behavior of the T-welded joint during the welding process. Experimental measurements have verified the validity of the established TEP FE model. Using the effective model, a series of numerical experiments are performed to obtain the inherent deformations under the conditions of different influencing factors, and then the calculation results are discussed based on the relevant data obtained.

Through numerical simulation analysis, it is found that the longitudinal and transverse inherent deformations decrease with the increase of welding speed and plate thickness, whereas as the nominal heat input increases, the inherent deformations increase significantly. The longitudinal shrinkage presents a quasi-linear and nonlinear distribution in the middle and end of the weld, respectively. The plastic strains in the cross section of the T-joint also vary greatly because of the process parameters and plate thickness, but the maximum value always appears near the location of the welding toe, which means that this point faces a relatively large risk of fatigue cracking. The inherent deformations are closely related to the plastic strains remaining in the weld zone and are also affected by many influencing factors such as process parameters and plate thickness.

In this study, relatively few influencing factors such as welding current, voltage, speed and plate thickness are considered to analyze the inherent deformations in the T-welded joint. Also, these influencing factors are all within a certain range of parameters, which shows that only limited applicability can be provided. In addition, only in-plane inherent deformations are considered in this study, without considering the other two out-of-plane components of inherent deformations.

This study can help to expand the understanding of the relationship between the inherent deformations and its influencing factors for a specific form of the welded joint, and can also provide basic data to supplement the inherent deformation database, thereby facilitating further researches on welding deformations for stiffened-panel structures in shipbuilding or steel bridges.

The structure stiffness is greatly affected by the fixture constraints during assembly due to the flexibility of large-scale thin-walled structures. The compliant deformation of structures is usually not consistent for the non-uniform stiffness in various clamping schemes. The purpose of this paper is to investigate the correlation between the assembly quality and the clamping schemes of structures with various initial deviations and geometrical parameters, which is based on the proposed irregular quadrilateral plate element via absolute nodal coordinate formulation (ANCF).

Two typical clamping schemes are specified for the large-scale thin-walled structures. Two typical deviation modes are defined in both free and clamping states in the corresponding clamping schemes. The new irregular quadrilateral plate element via ANCF is validated to analyze the compliant deformation of assembled structures. The quasi-static force equilibrium equations are extended considering the factors of clamping constraints and geometric deviations.

The initial deviations and geometrical parameters strongly affect the assembly deviations of structures in two clamping schemes. The variation tendencies of assembly deviations are demonstrated in details with the circumferential clamping position and axial clamping position in two clamping schemes, providing guidance to optimize the fixture configuration. The assembly quality of structures with deviations can be improved by configuration synthesis of the clamping schemes.

Typical over-constraint clamping schemes and deviation modes in clamping states are defined for large-scale thin-walled structures. The plate element via ANCF is extended to analyze the assembly deviations of thin-walled structures in various clamping schemes. Based on the proposed theoretical model, the effects of clamping schemes and initial deviations on the deformation and assembly deviation propagation of structures are investigated.

The deformation of a large fuselage panel is unavoidable due to its weak-stiffness and low-rigidity. Sometimes, the assembly accuracy of the panel is out of tolerance. The purpose of this paper is to propose a method to predict and correct the assembly deformation of a large fuselage panel during digital assembly by using a finite element (FE) analysis and partial least squares regression (PLSR) method.

A FE model is proposed to optimize the layout of load-transmitting devices to reduce panel deformation after the process of hoisting and supporting. Furthermore, another FE model is established to investigate the deformation behavior of the panel. By orthogonal simulations, the position error data of measurement points representing the precision of the panel are obtained. Then, a mathematical model of the relationship between the position errors of measurement points on the panel and the displacements of numerical control positioners is developed based on the PLSR method.

The case study shows that the model has a high level of computing accuracy and that the proposed method is an efficient way to correct the panel deformation in digital assembly.

The results of this study will enhance the understanding of the deformation behavior of a panel in aircraft digital assembly and help to improve the assembly precision systematically and efficiently.

The purpose of this paper is to analyze the variation of temperature field, pressure field and deformation of hydrostatic thrust bearing under different working conditions, so as to provide a theoretical basis for improving accuracy and reliability.

In this study, the double rectangular hydrostatic bearing of type Q1-224 was selected as the research object, and the simulation was carried out according to different working conditions, and the obtained data were summarized regularly.

It is found that the overall temperature of hydrostatic bearing increases with the increase of speed and load, and the increase in load will result in a larger pressure distribution which first increases and then decreases with the speed. The deformation trend of the deformation field is found, and it is found that the force deformation is larger than the thermal deformation at low rotational speed, and the thermal deformation is larger than the force deformation at high rotational speed.

In this study, the fluid-structure coupling method of conjugate heat transfer is applied to study the whole hydrostatic bearing. Most of the previous studies only studied the oil film and considered the influence of the convective heat transfer between the hydrostatic bearing and the air in heat transfer, which is rarely seen in the previous research literature.

The purpose of this paper is to predict the effect of bra pad specifications on breast deformation during jumping using a finite element (FE) method. Breast deformation is a key concern for women during exercise and can be effectively controlled with sports bras. In most studies, the deformation of breasts when wearing a sports bra is measured using motion capture devices to judge their effectiveness. However, the operation of such devices is highly complex and time-consuming. Computer-aided technology is an efficient way to simulate these experiments.

In this study, the breast model was obtained using three-dimensional (3D) scanning. Assembling models were obtained for FE analysis using reverse engineering and computer-aided design (CAD) software. The breast deformation results were obtained by completing pre-processing, solving and post-processing in the FE simulation software. To extend the application of these models, pads of different sizes and thicknesses within the bra were constructed to simulate the effect of pads on breast deformation.

The calculated root mean square errors were <1%, which indicated good agreement between the FE and experimental data in all the models. Nipple deformation was always the largest in most models. The smallest deformation occurred at the superior position of breasts in all models. In addition, larger pads were not effective in reducing breast deformation; however, thicker pads were.

The method developed in this study provides an effective way to predict breast deformation in multiple positions and is convenient for designing compression bras.

Riveting deformation is inevitable because of local relatively large material flows and typical compliant parts assembly, which affect the final product dimensional quality and fatigue durability. However, traditional approaches are concentrated on elastic assembly variation simulation and do not consider the impact of local plastic deformation. This paper aims to present a successive calculation model to study the riveting deformation where local deformation is taken into consideration.

Based on the material constitutive model and friction coefficient obtained by experiments, an accurate three-dimensional finite element model was built primarily using ABAQUS and was verified by experiments. A successive calculation model of predicting riveting deformation was implemented by the Python and Matlab and was solved by the ABAQUS. Finally, three configuration experiments were conducted to evaluate the effectiveness of the model.

The model predicting results, obtained from two simple coupons and a wing panel, showed that it was a good compliant with the experimental results, and the riveting sequences had a significant effect on the distribution and magnitude of deformation.

The proposed model of predicting the deformation from riveting process was available in the early design stages, and some efficient suggestions for controlling deformation could be obtained.

A new predicting model of thin-walled sheet metal parts riveting deformation was presented to help the engineers to predict and control the assembly deformation more exactly.

Current lubrication analyses of misaligned journal bearings are generally performed under some given preconditions. The purpose of this paper is to calculate the lubrication characteristics of a journal bearing with journal misalignment caused by shaft deformation under load, considering the surface roughness, thermal effect and (thermal and elastic) deformation of bearing surface simultaneously.

The lubrication of bearing was analyzed by average flow model based generalized Reynolds equation. The deformation of bearing surface under pressure or heat of oil film was calculated by compliance matrix method. The compliance matrix was established by finite element analysis. The temperature distributions of oil film and bearing were calculated by energy equation and heat conduction equation.

When the thermal deformation of bearing and journal surface is considered, the radius clearance affects not only the value of the maximum oil film pressure and minimum oil film thickness, but also the distribution of oil film pressure and thickness of misaligned bearing. The effect of thermal deformation of bearing on the performance of misaligned bearing is larger than that of elastic deformation of bearing. Whether or not the surface roughness affects the performance of misaligned bearing and the affecting level depends greatly on the condition of deformation of bearing surface.

The surface roughness, thermal effect and (thermal and elastic) deformation of bearing surface were considered simultaneously in the thermoelastohydrodynamic lubrication analysis of bearing with journal misalignment caused by shaft deformation under load. The results of this paper are helpful to the design of the bearing.

This paper describes the development and the numerical analysis of an electrochemical model for the analysis of a novel polymer/metal composite actuator. A general continuum model describing the transport and deformation processes of these actuators is briefly presented, along with a detailed description of the simulation scheme used to predict deformation, current, and mass transport. The predictions of the model are compared with experimental data, indicating a significant role of water transport in the large‐scale deformation. Comparison of the simulations and experimental data showed good agreement confirming the central role of water transport in the deformation process. For the sake of completeness the fabrication process and testing apparatus are also described.

This paper gives a review of the finite element techniques (FE) applied in the area of material processing. The latest trends in metal forming, non‐metal forming, powder metallurgy and composite material processing are briefly discussed. The range of applications of finite elements on these subjects is extremely wide and cannot be presented in a single paper; therefore the aim of the paper is to give FE researchers/users only an encyclopaedic view of the different possibilities that exist today in the various fields mentioned above. An appendix included at the end of the paper presents a bibliography on finite element applications in material processing for 1994‐1996, where 1,370 references are listed. This bibliography is an updating of the paper written by Brannberg and Mackerle which has been published in Engineering Computations, Vol. 11 No. 5, 1994, pp. 413‐55.

Manipulator motion accuracy is a fundamental requirement for precision manufacturing equipment. Light weight manipulators in high speed motions are vulnerable to deformations. The purpose of this work is to analyze the effect of link deformation on the motion precision of parallel manipulators.

The flexible dynamics model of the links is first established by applying the Euler–Bernoulli beam theory and the assumed modal method. The rigid-flexible coupling equations of the parallel mechanism are further derived by using the Lagrange multiplier approach. The elastic energy resulting from spiral motion and link deformations are computed and analyzed. Motion errors of the 3-link torque-prismatic-torque parallel manipulator are then evaluated based on its inverse kinematics. The validation experiments are also conducted to verify the numerical results.

The lateral deformation and axial deformation are largest at the middle of the driven links. The axial deformation at the middle of the driven link is approximately one-tenth of the transversal deformation. However, the elastic potential energy of the transversal deformation is much smaller than the elastic force generated from axial deformation.

Knowledge on the relationship between link deformation and motion precision is useful in the design of parallel manipulators for high performing dynamic responses.

This work establishes the relationship between motion precision and the amount of link deformation in parallel manipulators.