Search results

This study’s aim is to introduce a high-performance sorbent for the removal of both anionic (Congo red; CR) and cationic (methylene blue; MB) dyes from aqueous solutions.

Sodium silicate is adopted as a substrate for GO and AgNPs with positive charge are used as modifiers. The synthesized nanocomposite is characterized by FTIR, FESEM, EDS, BET and XRD techniques. Then, some of the most effective parameters on the removal of CR and MB dyes such as solution pH, sorbent dose, adsorption equilibrium time, primary dye concentration and salt effect are optimized using the spectrophotometry technique.

The authors successfully achieved notable maximum adsorption capacities (Qmax) of CR and MB, which were 41.15 and 37.04 mg g⁻¹, respectively. The required equilibrium times for maximum efficiency of the developed sorbent were 10 and 15 min for CR and MB dyes, respectively. Adsorption equilibrium data present a good correlation with Langmuir isotherm, with a correlation coefficient of R2 = 0.9924 for CR and R2 = 0.9904 for MB, and kinetic studies prove that the dye adsorption process follows pseudo second-order models (CR R2 = 0.9986 and MB R2 = 0.9967).

The results showed that the proposed mechanism for the function of the developed sorbent in dye adsorption was based on physical and multilayer adsorption for both dyes onto the active sites of non-homogeneous sorbent.

The as-prepared nano-adsorbent has a high ability to remove both cationic and anionic dyes; moreover, to the high efficiency of the adsorbent, it has been tried to make its synthesis steps as simple as possible using inexpensive and available materials.

Due to herbs and plants’ therapeutic properties and simplicity of availability in nature, humans have used them to treat a variety of maladies and diseases since ancient times. Later, as technology advanced, these plants and herbs gained significant relevance in some industries due to their suitable chemical composition, abundant availability and ease of access. Aegle marmelos is a species of plant that may be found in nature. Yet, little or very little literature was located on the coloration behavior of this plant’s leaves. This study aims to focus on the effect of different parameters on the extraction of colorant from Aegle marmelos leaves.

Some factors that affected on the extraction processes were examined and found to have significant impacts on the textile dyeing such as the initial dye concentration, extracted temperature, extracted bath pH and extracted time were all changed to see how they affected color extraction. The authors report a direct comparison between three heating methods, namely, microwave irradiation (MWI), ultrasonic waves (USW) and conventional heating (CH). The two kinetic models have been designed (pseudo-first and pseudo-second orders) in the context of these experiments to investigate the mechanism of the dyeing processes for fabrics under study. Also, the experimental data were analyzed according to the Langmuir and Freundlich isotherms.

From the result, it was discovered these characteristics were found to have a substantial effect on extraction efficiency. Temperature 90°C and 80°C when using CH and USW, respectively, while at 90% watt when using MWI, period 120 min when using CH as well as USW waves, while 40 min when using MWI, and pH 4, 5 and 10 for polyamide, wool and cotton, respectively, were the optimal extraction conditions. Also, the authors can say that wool gives a higher absorption than the other fabric. Additionally, MWI provided the best color strength (K/S) value, and homogeneity, at low temperatures reducing the energy and time consumed. The coloring follows the order: MWI > USW > CH. The adsorption isotherm of wool could be well fitted by Freundlich isotherm when applying CH and USW as a heating source, while it is well fitted by the Langmuir equation in the case of MWI. In the study, it was observed that the pseudo-first-order kinetic model fits better the experimental results of CH with a constant rate K₁ = −0.000171417 mg/g.min, while the pseudo-second-order kinetic model fits better the experimental results of absorption of both MWI (K2 = 38.14022572 mg/g.min) and USW (K₂ = 12.45343554 mg/g.min).

There is no research limitation for this work. Dye was extracted from Aegle marmelos leaves by applying three different heating sources (MWI, ultrasonic waves [USWW] and CH).

This work has practical applications for the textile industry. It is concluded that using Aegle marmelose leaves can be a possible alternative to extract dye from natural resource by applying new technology to save energy and time and can make the process greener.

Socially, it has a good impact on the ecosystem and global community because the extracted dye does not contain any carcinogenic materials.

The work is original and contains value-added products for the textile industry and other confederate fields.

The restoration and strengthening of QT600 is an industry bottleneck challenge. The Co-12 cladding layer has great wear and corrosion resistance. The purpose of this paper is to quantitatively reveal the transient evolution law of the corrosion process of Co-12 cladding layer on QT600 surface.

In this paper, a three-dimensional numerical model of the corrosion process of Co-12 cladding layer by QT600 laser cladding is established. The interaction between pitting pits and corrosion medium is considered to reveal the transient evolution of ion concentration, electrode potential, pH and corrosion rate at different locations.

The calculation shows that the ion concentration in pitting pit changes Cl⁻>Co²⁺>Na⁺, pH value decreases from top to bottom and corrosion rate at bottom is greater than that at top. The electrochemical corrosion test of Co-12 cladding layer was carried out. It is shown that the current density of QT600 increases by an order of magnitude compared to the Co-12 cladding layer, and the corrosion rate is 4.862 times higher than that of the cladding layer.

The results show that Co-12 cladding layer has great corrosion resistance, which provides an effective way for QT600 protection.

This study aims to dye silk with natural pigments extract of Coreopsis tinctoria, by treating the fabrics with appropriate mordant under suitable dyeing conditions, to achieve good dyeing depth, fastness and ultraviolet (UV) protection.

Firstly, single factor experiments were used to determine the basic dyeing conditions of Coreopsis tinctoria. The optimal process conditions for direct dyeing were determined through orthogonal experiments. After that, the dyeing with mordant was used. Based on the previously determined optimal process conditions, silk fabrics were dyed with different mordanting methods, with different mordants and mordant dosages. The dyeing results were compared, in terms of the K/S values of the dyed fabrics, to determine the most appropriate dyeing conditions with mordant.

The extract of Coreopsis tinctoria can dye silk fabrics satisfactorily. Good dyeing depth and fastness can be obtained by using suitable dyeing methods and dyeing conditions, especially when using the natural mordant pomegranate rind and the rare earth mordant neodymium oxide. The silk fabrics dyed with Coreopsis tinctoria have good UV resistance, which allows a desirable finishing effect to be achieved while dyeing, using a safe and environmentally friendly method.

The composition of Coreopsis tinctoria is complex, and the specific composition of colouring the silk fibre has not been determined. There are many factors that affect the dyeing experiment, which have an impact on the experimental results.

The results of this study may help expand the application of Coreopsis tinctoria beyond medicine.

To the best of the authors’ knowledge, this paper is the first report on dyeing silk with the extract of Coreopsis tinctoria achieving good dyeing results. Its depth of staining and staining fastness were satisfactory. Optimum dyeing method and dyeing conditions have been identified. The fabric dyed with Coreopsis tinctoria has good UV protection effect, which is conducive to improving the application value of the dyeing fabric. The findings help offer a new direction for the application of medicinal plants in the eco-friendly dyeing of silk.

This study aims to investigate the efficacy of Ag@GO/Na₂SiO₃ nanocomposite in eliminating As from aqueous solutions. Employing response surface methodology, the research systematically examines the adsorption process.

Various experimental parameters including sample pH, contact time, As concentration and adsorbent dosage are optimized to enhance the As removal process.

Under optimized conditions, the initial As concentration, contact time, pH and adsorbent dosage are determined to be 32 ppm, 50 mins, 6.5 and 0.4 grams, respectively. While the projected removal of As stands at 97.6% under these conditions, practical application achieves a 93% removal rate. Pareto analysis identifies the order of significance among factors as follows: adsorbent dosage > contact time > pH > As concentration.

This study highlights the potential Ag@GO/Na₂SiO₃ as a promising adsorbent for efficiently removing industrial As from aqueous solutions, and it is likely to have a good sufficiency in the filtration of water and wastewater treatment plans to remove some chemical pollution, including paints and heavy metals.

The simplicity of the nanocomposite preparation method without the need for advanced equipment and the cheapness of the raw materials and its potential ability to remove As are the prominent advantages of this research.

This study aims to develop eco-friendly corrosion inhibitors for aluminum in acidic media by evaluating the corrosion inhibition properties of corn leaf extract (CLE) using response surface methodology (RSM) and experiments.

The RSM was combined with experiments to evaluate the corrosion inhibition properties of CLE on aluminum in acid media.

The effectiveness of the inhibition increased with increasing inhibitor concentration and time but decreased with increasing temperature. The corrosion inhibition mechanism revealed the corrosion process is spontaneous exothermic physical adsorption. Thermodynamic parameters revealed an activation energy between 32.1 and 24.7 kJ/mol, energy of adsorption between −14.53 and −65.07 and Gibbs free energy of −10.12 kJ/mol which indicated the CLE exothermically spontaneously physisorbed. A model was generated to estimate the effect of the process parameters (inhibitor concentration, reaction time and temperature) using the RSM. Optimization of the process factors was also carried out using the RSM. The percentage inhibition efficiency obtained experimentally (85.61%) was closely comparable to 84.89% obtained by the theoretical technique (RSM). The SEM observations of the inhibited and uninhibited Al samples demonstrated that CLE is an effective corrosion inhibitor for aluminum in acid media.

Results herein provide novel information on the possible application of CLEs as effective eco-friendly corrosion inhibitors.

This paper aims to focus on the aqueous extraction of natural dye from haematoxylum campechianum L. bark for finishing the bio-mordant cotton fabrics producing value-added, environment-friendly textile products, for biomedical applications.

The study focuses on the creation of eco-friendly bio-mordant cotton fabric using gallic acid and gelatin, Al³⁺ and Fe²⁺ salts and metal mordant. The optimal pH for extraction, structural characterization and phytochemical analysis of the extracted dye were estimated using UV-visible spectrophotometer, FTIR and qualitative analysis. Variations in electrolyte concentration and pH medium were also considered. The study also examines build-up properties, colorimetric values and fastness characteristics of the colored fabrics.

All the dyed fabrics exhibit very good to excellent in terms of antimicrobial resistance against S. aureus and C. allbicans.

Pre-mordant cotton fabrics with Fe²⁺ and a combination of metal and bio-mordant show higher antibacterial resistance against P. aerugionsa. Further, bio-mordant and a combination of both mordant exhibit excellent UV protection and antioxidant activity performance compared to that of undyed fabrics.

This work opens up a huge potential for producing healthy bioactive-colored fabrics used in medical textiles and other usages.

This study aims to investigate the morphology and physicochemical properties of BiOBr/Polyvinylidene fluoride (PVDF) composite membranes and the differences in the properties of BiOBr/PVDF composite membranes made by adding different precursor ratios during the casting process.

In this paper, sodium bromide and Bi(NO3)3 were used as precursors for the preparation of BiOBr photocatalysts, and PVDF membranes were modified by using the phase conversion method in conjunction with the in situ deposition method to produce BiOBr/PVDF hydrophilic composite membranes with both membrane separation and photocatalytic capabilities.

The characterization results confirmed that the composites were successfully and homogeneously co-mingled in the PVDF membranes. The related performance of the composite membrane was tested, and it was found that the composite membrane with the optimal precursor incorporation ratio had good photocatalytic efficiency and antipollution ability; the removal efficiencies of methyl orange, rhodamine B and methylene blue were 80.43%, 85.02% and 86.94%, respectively, in 2.5 h. The photocatalytic efficiency of composite membranes with different precursor ratios increased and then decreased with the increase of the precursor addition ratio.

The composite membrane is prepared by phase conversion method with in situ deposition method, and the BiOBr material has unique advantages for the degradation of organic dyes. The comprehensive experimental data can be known that the composite membrane prepared in this paper has high degradation efficiency and good durability for organic dyes.

Hexavalent chromium has been a benchmark corrosion inhibitor before it was phased out because of its carcinogenic properties. However, because it was phased out, many alternative corrosion inhibitors have been introduced but failed to meet the performance of this benchmark inhibitor. Consequently, benzotriazole (BTA) was reported to exhibit chromate-like inhibition performance. Subsequently, Intelli-ion was reported by researchers to exhibit chromate-like performance also with claims of being a unique alternative. This paper aims to review the inhibition performance of these two alternatives. Above all, promotes the unique inhibition performance of Intelli-ion that makes it suitable for application in many sectors.

In this paper, the corrosion inhibition performances of BTA and Intelli-ion were compared systematically by reviewing some related literatures based on the opinion of the authors.

Different methodologies for measuring the inhibition performance of BTA showed that it’s an inhibitor of choice. However, the cut edge corrosion performance of Intelli-ion and BTA corrosion inhibitors on galvanized steel of 55% Wt.% Al, 44% Wt.% Zn and 1% Wt.% Si in 5 Wt.% NaCl solution was compared when subjected to scanning vibrating electrode technique (SVET) for 24 h. The results showed faint blue-colored region depicting negative cathodic current density for the Intelli-ion while there was a high-intensity of red-colored region depicting a positive anodic current density for BTA. In other words, the Intelli-ion inhibitor had a better overall cut-edge corrosion inhibition performance than the BTA inhibitor.

This paper compares and further, summarizes the corrosion inhibition performance of Intelli-ion and BTA by evaluating SVET results from the literature. In addition, it serves as an overview and reference for the unique inhibition performance of Intelli-ion when applied in field applications.

Using coconut shell aggregates (CSA) in concrete benefits agricultural waste management and reduces the demand for mineral resources. Several studies have found that concrete containing CSA can achieve strengths that are comparable to regular concrete. The purpose of the present work is to evaluate the concrete’s durability-related properties to supplement these earlier findings.

Cylindrical specimens were prepared with a constant water–cement ratio of 0.50 and CSA content ranging from 0% to 50% (at 10% increment) by volume of the total coarse aggregates. The specimens were cured for 28 days and then tested for density, surface hardness, electrical resistivity and water sorptivity. The surface hardness was measured to describe the concrete resistance to surface wearing, while the resistivity and sorptivity were evaluated to describe the material’s resistance to fluid penetration.

The results showed that the surface hardness of concrete remained on average at 325 Leeb and did not change significantly with CSA addition. The distribution of surface hardness was also similar across all CSA groups, with the interquartile range averaging 59 Leeb. These results suggest that the cement paste and gravel stiffness had a more pronounced influence on the surface hardness than CSA. On the other hand, concrete became lighter by about 9%, had lower resistivity by 80% and had significantly higher initial sorptivity by up to 110%, when 50% of its natural gravel was replaced with CSA. Future work may be done to improve the durability of CSA when used as coarse aggregate.

The present study is the first to show the lack of correlation between CSA content and surface hardness. It would mean that the surface hardness test may not completely capture the porous nature of CSA-added concrete. The paper concludes that without additional treatment prior to mixing, CSA may be limited only to applications where concrete is not in constant contact with water or deleterious substances.