Search results

In experiments utilising sweat solution and distilled water, seamed ensembles performed less thermally efficiently than unseamed fabrics.

Water may not accurately reflect perspiration when testing multi-layered clothes for thermal comfort in wet state. Most researchers used water or sodium chloride (NaCl) to measure wet state thermal comfort. However, human perspiration is an extremely complex mixture of aqueous chemicals, including minerals, salts, lipids, urea and lactic acid. This study compares the effects of simulated sweat solution to distilled water on the thermal behaviour of a multi-layered fabric assembly with different seam patterns.

Experiment results show that stitching decreases thermal resistance and thermal conductivity. Seam pattern of 10 cm diagonal spacing is more thermally resistant than 2.5 cm diagonal spacing. In comparison to that of simulated sweat, fabric that has been moistened with distilled water exhibits increased thermal conductivity. Hollow polyester wadding or micro polyester wadding as the intermediate layer exhibits greater thermal resistance than multi-layered construction with spacer fabric as middle layer.

This study considers human perspiration while designing protective clothing for wet thermal comfort.

The purpose of this work is to investigate the effect of filament composition with different specifications on the thermal comfort properties of bi-layer knitted fabrics.

In this paper eight bi-layer knitted fabrics with the same knitting structure but different filament compositions were prepared, and the thermal-wet comfort properties of these fabrics were examined. According to experimental data, the effect of filament composition on the thermal comfort properties of fabric was analyzed.

The increasing difference of hydrophilicity between inner and outer layers resulted in the enhancement of moisture management properties. Better thermal-physiology performance was exhibited by fabrics made up of finer and circular section fibers. Excellent thermal transfer, drying performance and one-way water transport capacity benefited the improvement of dynamic cooling effect of fabrics.

This work provides a useful and effective method for the development of bi-layer knitted fabric applied for sports and summer clothing.

Perspiration and heat are produced by the body and must be eliminated to maintain a stable body temperature. Sweat, heat and air must pass through the fabric to be comfortable. The cloth absorbs sweat and then releases it, allowing the body to chill down. By capillary action, moisture is driven away from fabric pores or sucked out of yarns. Convectional air movement improves sweat drainage, which may aid in body temperature reduction. Clothing reduces the skin's ability to transport heat and moisture to the outside. Excessive moisture makes clothing stick to the skin, whereas excessive heat induces heat stress, making the user uncomfortable. Wet heat loss is significantly more difficult to understand than dry heat loss. The purpose of this study is to provided a good compilation of complete information on wet thermal comfort of textile and technological elements to be consider while constructing protective apparel.

This paper aims to critically review studies on the thermal comfort of textiles in wet conditions and assess the results to guide future research.

Several recent studies focused on wet textiles' impact on comfort. Moisture reduces the fabric's thermal insulation value while also altering its moisture characteristics. Moisture and heat conductivity were linked. Sweat and other factors impact fabric comfort. So, while evaluating a fabric's comfort, consider both external and inside moisture.

The systematic literature review in this research focuses on wet thermal comfort and technological elements to consider while constructing protective apparel.

The purpose of this research is to assess the removal of oil spills from the seawater surface as well as the antibacterial activity of ZnFe₂O₄-cetyltrimethylammonium bromide (CTAB, cationic surfactant) magnetic nanoparticles (ZFO-CTAB MNPs).

A CTAB-assisted sol–gel method was used to synthesize ZFO-CTAB MNPs. X-ray powder diffraction and Fourier transform infrared spectroscopy were used for ZFO-CTAB MNPs characterization. Also, the magnetic force and apparent density of ZFO-CTAB MNPs were determined. The oil spill cleanup was investigated by using the gravimetric oil removal (GOR) technique, which used ZFO-CTAB MNPs as oil absorbent material and four oil samples (crude, diesel, gasoline and used oil) as oil spill models. The antibacterial activity of ZFO-CTAB MNPs against Gram-negative bacteria (Pseudomonas aeruginosa, Escherichia coli and Salmonella typhi) was investigated by using the optical density method.

The results revealed that, when the amount of ZFO-CTAB was 0.01 g, gasoline oil had the highest GOR (51.80 ± 0.88 g/g) and crude oil had the lowest (11.29 ± 0.82 g/g). Furthermore, for Escherichia coli, Salmonella typhi and Pseudomonas aeruginosa, ZFO-CTAB MNPs inhibited bacterial growth with a higher percentage (94.24%–95.63%).

The applications of ZFO-CTAB MNPs in the cleanup of oil spills from aqueous solutions, as well as their antibacterial activity. The results showed that ZFO-CTAB MNPs are a promising material for removing oil spills from bodies of water as well as an antibacterial agent against Gram-negative bacterial strains.

This paper aims to investigate the influence of picking sequence, weave design and weft yarn material on the thermal conductivity of the woven fabrics.

This work includes the development of 36 woven samples with two weave designs (1/1 plain and 3/1 twill), three picking sequences (single, double and three pick insertion) and six different weft yarn materials (cotton, polyester having 48 filaments, polyester with 144 filaments, spun coolmax having Lycra in core and coolmax in sheath, filament coolmax and polypropylene). The thermal conductivity was measured using ALAMBETA tester.

The results showed that weft yarn material, weave design and picking sequence have a meaningful impact on the thermal conductivity of woven fabric. The value of thermal conductivity was lowest for the fabrics with three pick insertion and 3/1 twill weave in all weft yarn materials.

Plain woven fabric with single pick insertion is feasible for summer wear to enhance the comfort of wearer. By changing the warp yarn grouping and material, improved thermal conductivity/resistance can also be achieved.

The authors have studied the combined effect of different weft yarn materials with different picking sequences and different weave designs on thermal conductivity of the woven fabrics.

Various approaches have been made to alter the vibration sensing properties of zinc oxide (ZnO) films to achieve high sensitivity. This paper aims to report the experimental study of the fabrication of precursor molar ratio concentration varied ZnO nanostructures grown on rigid substrates using the refresh hydrothermal method. The effect of these fabricated ZnO nanostructures-based vibration sensors was experimentally investigated using a vibration sensing setup.

ZnO nanostructures have been grown using low temperature assisted refresh hydrothermal method with different precursor molar concentrations 0.025 M (R1), 0.075 M (R2) and 0.125 M (R3). Poly 3,4-ethylenedioxythiophene polystyrene sulfonate, a p-type material is spun coated on the grown ZnO nanostructures. Structural analysis reveals the increased intensity of the (002) plane and better c-axis orientation of the R2 and R3 sample comparatively. Morphological examination shows the changes in the grown nanostructures upon increasing the precursor molar concentration. The optical band gap value decreases from 3.11 eV to 3.08 eV as the precursor molar concentration is increased. Photoconductivity study confirms the formation of a p-n junction with less turn-on voltage for all the fabricated devices. A less internal resistance of 0.37 kΩ was obtained from Nyquist analysis for R2 compared with the other two fabricated samples. Vibration testing experimentation showed an improved output voltage of the R2 sample (2.61 V at 9 Hz resonant frequency and 2.90 V for 1 g acceleration) comparatively. This also gave an increased sensitivity of 4.68 V/g confirming its better performance when compared to the other fabricated two samples.

Photoconductivity study confirms the formation of a p-n junction with less turn-on voltage for all the fabricated devices. A less internal resistance of 0.37 kΩ was calculated from the Nyquist plot. Vibration testing experimentation proves an increased sensitivity of 4.68 V/g confirming its better performance when compared to the other fabricated two samples.

Vibration testing experimentation proves an increased sensitivity of 4.68 V/g for R2 confirming its better performance when compared to the other fabricated two samples.

The host–guest molecules are often used in various fields and applications. This paper aims to discuss the role of host–guest complexes in the textile industry, focusing on calixarenes as a potential adsorbent for hazardous dyes. The paper begins with an introduction to nanotechnology and its many uses, including textiles.

The risks associated with the utilisation of dyes and its adverse effects on the environment are then also highlighted. This paper also discusses the structure and characteristics of calixarenes and their potential use as an adsorbent to extract toxic metals from aqueous solutions. The paper also explains the molecular structure of calixarenes, especially the ability of its upper and lower rims, which can be altered to yield derivatives with various selectivities for diverse guest ions and small molecules. In addition, the application of various host–guest molecules in the textiles industry to extract dyes also had been discussed.

In conclusion, the paper highlights the essential in establishing a systematic review on the significance of selective adsorbents, such as calixarenes, to isolate particular targets from diverse matrices in the textile industry.

Only discussing several applications for several host–guest molecules.

The paper concisely describes various host–guest molecule applications in the textile industry, with each molecule being elaborated upon in detail.

Water vapor trapped in the boundary layer between a person and the clothing creates discomfort and other unpleasant sensations. When that water vapor is prevented from leaving the clothing by external vapor barriers or impermeable layers, those psychophysical states are further exacerbated. One situation where that can be problematic is in office workplaces, and the seats that workers use for many hours every day. This study aims to evaluate the impact of different fabrics that are used for seat cover on water vapor retention.

The authors' method determines the behavior of contact surface humidity with a 50 kg sandbag on the seat to mimic the deformation of the seat materials due to the seated person's weight. Thus, the maximum increase in relative humidity (RH) after humidification of the seat surface (ΔRH-max), the time required to reach the maximum value of humidity (t-max) and the time constant (TC) after humidity starts to fall were derived.

Of the three different seat covers tested, the ΔRH-max of the wool were 7.3–8.8%, compared to 27.0–29.0% of the polyvinyl chloride (PVC), indicating more moisture absorption and transmission of the wool. The TC of the acrylic cover was 224–384 min compared to the 483–558 min of the PVC, which indicated a quick drying out feature of the acrylic.

The ΔRH-max, t-max and TC were all significantly correlated with the RH at the back thigh skin surface of the actual human participants.

Sleep quality, a crucial parameter for health and life performance, is affected by mattress components; particularly mechanical and thermal comfort management ability of the upper layers. The aim of this study is to investigate effects of quilted mattress ticking fabric material (polyester, polypropylene, viscose, lyocell and their blends) on thermal comfort of the bedding system by objective and subjective measurements.

The permeability (air and water vapour), heat transfer, water absorption, transfer and drying behaviours of knitted quilted fabrics which influence the thermal comfort of the bedding system were investigated. Subjective coolness and dampness evaluations were gathered by forearm and hand-palm tests to provide more realistic discussion in light of fabric characteristics.

According to the results, polypropylene can be suggested for winter use with its higher air and water vapour permeabilities, lower thermal absorption and conductivities and warmer evaluation results. Lyocell can be suggested for summer use with also high permeabilities, higher thermal absorption and conductivities and cooler evaluation results. Polyester and viscose may also be considered for winter and summer in turn as a result of thermal feelings they create.

In addition to fabric thermal, permeability, liquid absorption and transfer properties, this study also includes subjective coolness and dampness evaluations which can provide realistic results regarding the coolness-to-touch and liquid transfer performances of mattress ticking fabrics. The relationships among objective and subjective data were investigated and the proposed subjective evaluation techniques can be used for different products.

This paper aims to develop bilayer woven fabrics with different picking sequences with enhanced comfort without any change in the constituent materials.

Six bilayer woven fabrics were produced on Dobby loom with 3/1 twill weave using micro-polyester yarn. Three different picking sequences, i.e. single pick insertion (SPI), double pick insertion (DPI) and three pick insertion (3PI), were used in both face and back layers. The effect of picking sequence on air permeability (AP), volume porosity, thermal resistance and overall moisture management capability (OMMC) of the samples were analyzed.

The results showed that 3PI–3PI picking sequence gives the highest OMMC, AP and thermal resistance in bilayer woven fabrics and the least results exhibited by SPI–SPI picking sequence.

This research uses a bilayer woven system that develops channels and trapes the air causing higher thermal resistance; therefore, applicable for winter sports clothing rather than for summer wear. Developed bilayer woven fabrics can be used in winter sportswear to improve the comfort of the wearer and reduce fatigue during activity.

Authors have developed bilayer fabrics by changing the picking sequences, i.e. SPI, DPI and 3PI of weft yarns in both layers and compared their thermo-physiological comfort properties.