Search results

The purpose of this paper is to investigate the friction and sealing characteristics of narrow end face seal ring with spiral grooves for wet clutch by experiment.

The shallow spiral grooves are machined in the end face of narrow seal ring by laser, and all of other parameters of specimens are the same with the actual production. The investigation of friction and sealing characteristics are carried out by comparing the experiment results of end face seal ring with spiral grooves with the conventional seal ring without spiral grooves through friction coefficient test, volume leakage rate test and pv value test.

Comparing with conventional seal ring without spiral grooves, seal ring with spiral grooves experiences boundary lubrication, mixed lubrication and fluid film lubrication with the increase of rotation speed, whereas the conventional seal ring only experiences mixed lubrication. Besides this, the volume leakage rate is slightly larger, but the pv value is much larger than that of conventional seal ring.

Effect of spiral grooves on the friction and sealing characteristics of narrow end face seal ring for wet clutch is investigated. The improved lubrication performance can be achieved by shallow spiral grooves even if the distance of radius difference used to machine grooves is very small.

To develop a more realistic model for molecularly thin film hydrodynamic lubrication by incorporating the fluid inhomogeneity and discontinuity effects across the fluid film thickness in this lubrication.

The total mass flow of the fluid through the contact in a basic one‐dimensional molecularly thin film hydrodynamic lubrication is studied by incorporating the fluid inhomogeneity and discontinuity effects across the fluid film thickness, based on a simplified momentum transfer model between neighboring fluid molecules across the fluid film thickness. This flow is calculated according to the present approach and the theory of viscous flow between two contact surfaces. The total mass flow of the fluid through the contact in this lubrication is also calculated from conventional hydrodynamic lubrication theory, which was based on continuum fluid assumption in the whole lubricated contact. The ratio of this flow calculated from the present approach to that calculated from conventional hydrodynamic lubrication theory is here defined as the flow factor for a one‐dimensional molecularly thin film hydrodynamic lubrication due to the fluid inhomogeneity and discontinuity effects. Results of this flow factor are presented for wide operational parameters.

In the molecularly thin film hydrodynamic lubrication, when the fluid inhomogeneity and discontinuity across the fluid film thickness both are incorporated, the total fluid mass flow through the contact and thus the global fluid film thickness are increased. The combined effect of the fluid inhomogeneity and discontinuity across the fluid film thickness on the total fluid mass flow through the contact in this lubrication is determined by the operational parameter K=((∂p/∂xh²)/[6η_bulk(1−ξ)(u_a+u_b)]); when the operational parameter K is high, this effect is significant; when the operational parameter K is low, this effect is negligible. On the other hand, in this lubrication, when the combined effect of the fluid inhomogeneity and discontinuity across the fluid film thickness is incorporated, the shear stresses at the contact‐fluid interfaces are reduced and this reduction can be significant. This reduction may strongly depend on the value of the dimensionless discontinuity parameter Δ/D of the fluid across the fluid film thickness but weakly depend on the number n of the fluid molecules across the fluid film thickness.

An important and very useful research for the academic researcher and the engineer who are, respectively, engaged in the study and design of hydrodynamic lubrication on mechanical components especially of very low hydrodynamic lubrication film thickness. It is also important to the subsequent research of molecularly thin film hydrodynamic lubrication.

A new model of molecularly thin film hydrodynamic lubrication in one‐dimensional contacts is originally proposed and described by incorporating the fluid inhomogeneity and discontinuity effects across the fluid film thickness in this lubrication. This new model of molecularly thin film hydrodynamic lubrication is of importance to the theoretical study of molecularly thin film hydrodynamic lubrication.

This study aims to investigate the effects of irregular groove textures on the friction and wear performance of sliding contact surfaces. These textures possess multiple depths and asymmetrical features. To optimize the irregular groove texture structure of the sliding contact surface, an adaptive genetic algorithm was used for research and optimization purposes.

Using adaptive genetic algorithm as an optimization tool, numerical simulations were conducted on surface textures by establishing a dimensionless form of the Reynolds equation and setting appropriate boundary conditions. An adaptive genetic algorithm program in MATLAB was established. Genetic iterative methods were used to calculate the optimal texture structure. Genetic individuals were selected through fitness comparison. The depth of the groove texture is gradually adjusted through genetic crossover, mutation, and mutation operations. The optimal groove structure was ultimately obtained by comparing the bearing capacity and pressure of different generations of micro-convex bodies.

After about 100 generations of iteration, the distribution of grooved textures became relatively stable, and after about 320 generations, the depth and distribution of groove textures reached their optimal structure. At this stage, irregular texture structures can support more loads by forming oil films. Compared with regular textures, the friction coefficient of irregular textures decreased by nearly 47.01%, while the carrying capacity of lubricating oil films increased by 54.57%. The research results show that irregular texture structures have better lubrication characteristics and can effectively improve the friction performance of component surfaces.

Surface textures can enhance the friction and lubrication performance of metal surfaces, improving the mechanical performance and lifespan of components. However, surface texture processing is challenging, as it often requires multiple experimental comparisons to determine the optimal texture structure, resulting in high trial-and-error costs. By using an adaptive genetic algorithm as an optimization tool, the optimal surface groove structure can be obtained through simulation and modeling, effectively saving costs in the process.

Through practical tests, it has been found that steel balls based on different standards could affect tribological performances of the same lubricant, but unfortunately, past researches in the field have been quite inadequate. The aim of this paper, therefore, is conscientiously to study the problem.

The anti‐wear properties of four kinds of lubricants were evaluated by four‐ball tester using two kinds of steel balls based on different standards. The reason for different anti‐wear properties of the same lubricant was also discussed using hardness tester and scanning electron microscope with an energy dispersive spectrometer (SEM/EDS).

It was found that steel balls based on different standards could affect the tribological results for the same lubricant. The reason could lie in the surface chemical composition, surface roughness and hardness of steel balls which originated from the subtle difference of different standards.

The paper shows that, as far as evaluating anti‐wear properties is concerned, steel ball based on AISI Standard Steel No. E‐52100 is a better choice than that based on Chinese standard GB 308.

To review, analyze and present the effects of the contact‐fluid interfacial shear strength and contact‐fluid interfacial slippage and the critical importance of these effects in elastohydrodynamic lubrication (EHL).

The experimental and theoretical research results of the contact‐fluid interfacial shear strength and its caused contact‐fluid interfacial slippage in hydrodynamic lubrication and especially in EHL obtained in the past decades and progressed in recent years by the present author and by others are reviewed. Analysis and presentation are made on both the contact‐fluid interfacial shear strength versus fluid pressure curve for a given bulk fluid temperature in an isothermal EHL and the influence of the bulk fluid temperature on this curve.

It is very clearly and well understood from the present paper that the value of the contact‐fluid interfacial shear strength in the inlet zone in an EHL contact, i.e. at low EHL fluid film pressures is usually low and usually has rather a weak dependence on the EHL fluid film pressure. This proves the correctness of the EHL theories previously developed by the author based on the assumption of this low value and dependence on the EHL fluid film pressure of the contact‐fluid interfacial shear strength. It is also very clearly understood that the bulk fluid temperature usually has a strong influence on the value of the contact‐fluid interfacial shear strength in EHL and the increase of this temperature usually significantly reduces the value of the contact‐fluid interfacial shear strength in EHL.

A very useful material for the engineers who are engaged in the design of EHL on gears, cams and roller bearings, and for the tribology scientists who thrust efforts in studying EHL and mixed EHL both by theoretical modeling and by experiments.

A new and generalized mode of mixed EHL is originally proposed by incorporating the finding of a more realistic mode of the contact regimes in a practical mixed EHL based on the contact‐fluid interfacial shear strength and contact‐fluid interfacial slippage effects. This mode of mixed EHL should become the direction of the theoretical research of mixed EHL in the future.

THE first part of Professor Duncan Dowson's paper (March/April issue) dwelt on late 19th century development of machinery outstripping the performance of available lubricants. Contemporary lubricant research, and personalities involved, where described, leading to the concept of fluid‐film lubrication, documented by Professor Osborne Reynolds' paper read to the Royal Society in 1886.

To form and develop a new mode of mixed elastohydrodynamic lubrication (mixed EHL) which is more realistic and of more application values to a practical elastohydrodynamic contact on gears, cams and roller bearings than the previous and current existing mixed EHL models.

The representative theoretical and experimental studies on elastohydrodynamic lubrication (EHL) and mixed EHL carried out in the previous and recent time, including those of the author, are reviewed. The obtained results on EHL and mixed EHL in those studies and the viewpoints on the mode of mixed EHL based on those results developed in those studies are compared and evaluated. Strong proves are formed on the new mode of mixed EHL proposed in the present paper based on these comparisons and evaluations.

Strong viewpoints are formed on the mode of the occurrence of dry contact in EHL in a practical concentrated contact. A new mode of mixed EHL is proposed by incorporating this mode of the occurrence of dry contact in EHL. Also, comments and evaluations on the previous researches on mixed EHL are made.

A very useful material for the engineers who are engaged in the design of EHL on gears, cams and roller bearings, and for the tribology scientists who thrust efforts in studying EHL and mixed EHL both by theoretical modeling and by experiments.

A new mode of mixed EHL is originally proposed by incorporating the finding of a more realistic mode of the occurrence of dry contact in EHL. This new mode of mixed EHL should become the direction of the theoretical research of mixed EHL in the future time. It provides a clearer way to this research.

THIS year marks the centenary of the publication of the most significant paper every written in the field of tribology. It is therefore timely to recall the nineteenth century developments in mechanical engineering science which prompted Osborne Reynolds to undertake his studies of fluid‐film lubrication, to consider the essence of his contribution, to review one hundred years of further progress and to comment on the current position.

This paper aims to investigate the lubrication regime in spherical pump, especially under different structural parameters and operational conditions.

A ball-on-plane configuration is adopted to represent the contact model between spherical piston and cylinder cover. The governing equations, which include the Reynolds and elasticity equations, are solved and validated by Jin–Dowson model. Both minimum film thickness and lambda ratio (ratio of minimum fluid film thickness to combined surface roughness of the piston and cylinder cover) of the equivalent model are obtained using an established model.

The results indicate that piston diameter and radial clearance are the two main factors affecting the pump lubrication regime. Other related parameters such as rotation speed of the piston, load, viscosity of working medium, material matching and surface roughness of piston and cylinder cover also have different impacts on the lubrication regime of the spherical pump.

These results emphasize the importance of the design and manufacturing parameters on the tribological performance of spherical pumps and these are also helpful in improving the spherical pump lubrication regime and enlarging its life cycle. This is to certify that to the best of the authors’ knowledge, the content of this manuscript is their own work. This manuscript has only been submitted to this journal and never been published elsewhere. The authors certify that the intellectual content of this manuscript is the product of their own work and that all the assistance received in preparing this manuscript and sources has been acknowledged.