Search results

Arthroscopic osteochondroplasty is a minimally invasive procedure that has been used to treat femoroacetabular impingement syndrome, leading to significant improvements in patients’ clinical outcomes and quality of life. However, some studies suggest that inadequate bone resection can substantially alter hip biomechanics. These modifications may generate different contact profiles and higher contact forces, increasing the risk of developing premature joint degeneration. To improve control over bone resection and biomechanical outcomes during arthroscopic osteochondroplasty surgery, this study aims to present a novel system for measuring femoroacetabular contact forces.

Following a structured design process for the development of medical devices, the steps required for its production using additive manufacturing with material extrusion and easily accessible sensors are described. The system comprises two main devices, one for measuring femoroacetabular contact forces and the other for quantifying the force applied by the assistant surgeon during lower limb manipulation. The hip device was designed for use within an arthroscopic environment, eliminating the need for additional portals.

To evaluate its performance, the system was first tested in a laboratory setup and later under in-service conditions. The 3D printing parameters were tuned to ensure the watertighness of the device and sustain the intraoperative fluid pressures. The final prototype allowed for the controlled measurement of the hip contact forces in real-time.

Using additive manufacturing and readily available sensors, the present work presents the first device to quantify joint contact forces during arthroscopic surgeries, serving as an additional tool to support the surgeon’s decision-making process regarding bone resection.

The purpose of this paper is to improve the problem of kinematics incompatibility of human–exoskeleton in the existing rigid lower-limb exoskeleton (LLE).

In this paper, following an introduction, the motion characteristics of the human knee joint and the design method of the exoskeleton were introduced. A kinematics model of the LLE based on cross-four-bar linkage was obtained. The structural parameters of the LLE mechanism were optimized by the particle swarm optimization algorithm. The predefined trajectories used in the optimization process were derived from the ankle joint, not the instantaneous center of rotation of the knee joint. Finally, the motion deviation of the optimization result was simulated, and the human–exoskeleton coordination experiment was designed to compare with the traditional single-axis knee joint in terms of comfort and coordination.

The lower limb exoskeleton mechanism obtained in this paper has a good tracking effect on human movement and has been improved in terms of comfort and coordination compared with the traditional single-axis knee joint.

The customized exoskeleton design method introduced in this paper is relatively simple, and the obtained exoskeleton has better movement coordination than the traditional exoskeleton. It can provide a reference for the design of lower limb exoskeleton and lower limb orthosis.

The purpose of this paper is to investigate the effect of plasma electrolytic oxidation (PEO) coatings and sealed PEO coatings on the corrosion resistance and cytocompatibility of a novel Mg-1Zn-0.45Ca alloy in simulated body fluid (SBF).

The microstructure, corrosion resistance and cytocompatibility of PEO coatings and phosphate conversion-treated PEO coatings were investigated and was compared with the bare Mg alloy.

The hot-extruded Mg-Zn-Ca alloy exhibit inhomogeneous microstructure and suffered from localized corrosion in the SBF. The PEO coating after phosphate conversion treatment offers enhanced protectiveness to the Mg alloy within an immersion period of up to 60 days, which is significantly improved compared with the performance of the PEO-coated Mg alloy, but the cytocompatibility was slightly decreased.

This work offers new perspective in balancing the protectiveness and cytocompatibility of bio-materials.

Integrating additive manufacturing (AM) tools in traditional mold-making provides complex yet affordable sand molds and cores. AM processes such as selective laser sintering (SLS) and Binder jetting three-dimensional printing (BJ3DP) are widely used for patternless sand mold and core production. This study aims to perform an in-depth literature review to understand the current status, determine research gaps and propose future research directions. In addition, obtain valuable insights into authors, organizations, countries, keywords, documents, sources and cited references, sources and authors.

This study followed the systematic literature review (SLR) to gather relevant rapid sand casting (RSC) documents via Scopus, Web of Science and EBSCO databases. Furthermore, bibliometrics was performed via the Visualization of Similarities (VOSviewer) software.

An evaluation of 116 documents focused primarily on commercial AM setups and process optimization of the SLS. Process optimization studies the effects of AM processes, their input parameters, scanning approaches, sand types and the integration of computer-aided design in AM on the properties of sample. The authors performed detailed bibliometrics of 80 out of 120 documents via VOSviewer software.

This review focuses primarily on the SLS AM process.

A SLR and bibliometrics using VOSviewer software for patternless sand mold and core production via the AM process.

Three-dimensional (3D) casting means using additive manufacturing (AM) techniques to print the mould for casting the cast tool. The printed mould, however, should be checked for its dimensional accuracy. 3D scanning can be used for the same. The purpose of this study is to combine the different AM techniques for 3D casting with 3D scanning to produce parts with close tolerance for preparing electrical discharge machining (EDM) electrodes.

The four processes, namely, stereolithography, selective laser sintering, fused deposition modelling and vacuum casting, are used to print the casting mould. The mould is designed in two halves, assembled to form a complete mould. The mould is 3D scanned in two stages: before and after using it as a casting mould. The mould's average and maximum dimensional deviations are calculated using 3D-scanned results. The eutectic Sn-Bi alloy is cast in the mould. The surface roughness of the mould and the cast tool are measured.

The cast tool is selected from the four processes in terms of dimensional accuracy and surface finish. The same is electroplated with copper. The microstructure of the cast tool (low-melting-point alloy) and deposited copper is analysed using a scanning electron microscope. Energy dispersive spectroscopy and X-ray diffraction techniques are used to verify the composition of the cast and coated alloy. The electroplated tool is finally tested on the EDM setup. The material removal rate and tool wear are measured. The performance is compared with a solid copper tool. The free-form customised EDM mould is also prepared, and the profile is cast out. The same is tested on the EDM. Thus, the developed path can be successfully used for rapid tooling applications.

The eutectic composition of Sn-Bi is cast in the 3D-printed mould using different AM techniques combined with 3D scanning quality to check its feasibility as an EDM electrode, which is a novel work and has not been done previously.