Search results

This study aims to analyze the factors, evaluation techniques of the durability of existing railway engineering.

China has built a railway network of over 150,000 km. Ensuring the safety of the existing railway engineering is of great significance for maintaining normal railway operation order. However, railway engineering is a strip structure that crosses multiple complex environments. And railway engineering will withstand high-frequency impact loads from trains. The above factors have led to differences in the deterioration characteristics and maintenance strategies of railway engineering compared to conventional concrete structures. Therefore, it is very important to analyze the key factors that affect the durability of railway structures and propose technologies for durability evaluation.

The factors that affect the durability and reliability of railway engineering are mainly divided into three categories: material factors, environmental factors and load factors. Among them, material factors also include influencing factors, such as raw materials, mix proportions and so on. Environmental factors vary depending on the service environment of railway engineering, and the durability and deterioration of concrete have different failure mechanisms. Load factors include static load and train dynamic load. The on-site rapid detection methods for five common diseases in railway engineering are also proposed in this paper. These methods can quickly evaluate the durability of existing railway engineering concrete.

The research can provide some new evaluation techniques and methods for the durability of existing railway engineering.

This paper aims to investigate the effect of physical vapor deposition (PVD)-coated stencil wall aperture on the life span of fine-pitch stencil printing.

The fine-pitch stencil used in this work is fabricated by electroform process and subsequently nano-coated using the PVD process. Stencil printing process was then performed to print the solder paste onto the printed circuit board (PCB) pad. The solder paste release was observed by solder paste inspection (SPI) and analyzed qualitatively and quantitatively. The printing cycle of up to 80,000 cycles was used to investigate the life span of stencil printing.

The finding shows that the performance of stencil printing in terms of solder printing quality is highly dependent on the surface roughness of the stencil aperture. PVD-coated stencil aperture can prolong the life span of stencil printing with an acceptable performance rate of about 60%.

Stencil printing is one of the important processes in surface mount technology to apply solder paste on the PCB. The stencil’s life span greatly depends on the type of solder paste, stencil printing cycles involved and stencil conditions such as the shape of the aperture, size and thickness of the stencil. This study will provide valuable insight into the relationship between the coated stencil wall aperture via PVD process on the life span of fine-pitch stencil printing.

This paper aims to compare the wear behavior, surface roughness, friction coefficient and volume loss of high-velocity oxy-fuel (HVOF) sprayed WC–Co and WC–Cr₃C₂–Ni coatings on AISI 1095 steel with spraying times of 10 and 15 s.

In this study, the pin-on-disc testing technique was used to evaluate the wear characteristics at a speed of 0.24 m/s, load of 40 N and test time of 60 min under dry conditions at room temperature. The wear characteristics were examined and analyzed by scanning electron microscopy and energy dispersive X-ray spectroscopy. The surface roughness of a coated surface was measured, and microhardness measurements were performed on the cross-sectioned and polished surfaces of the coating.

Spraying time and powder material affected the hardness of HVOF coatings due to differences in the porosity of the coated layers. The average hardness of the WC–Cr₃C₂–Ni coating with a spaying time of 15 s was approximately 14% higher than that of the WC–Cr₃C₂–Ni coating with a spraying time of 10 s. Under an applied load of 40 N, the WC–Co coating with a spraying time of 15 s had the lowest variation in the friction coefficient compared with the other coatings. The WC–Co coating with a spraying time of 10 s had the lowest average and variation in volume loss compared to the other coatings. The WC–Cr₃C₂–Ni coating with a spraying time of 10 s exhibited the highest average volume loss. The wear features changed slightly with the spraying time owing to variations in the hardness and friction coefficient.

This study investigated tribological performance of WC–Co; WC-Cr₃C₂-Ni coatings with spraying times of 10 and 15 s using pin-on-disc tribometer by rotating the relatively soft pin (C45 steel) against hard coated substrate (disc).

The purpose of this paper is to study the effect of surface salt spray duration on the fretting wear and electrochemical corrosion behaviors of Inconel 690 alloy.

A high-temperature steam generator was applied to salt spray test samples, a fretting wear rig was used to realize the damage behavior tests, an electrochemical workstation was applied to analysis the changes of each sample’s corrosion dynamic response before and after fretting wear.

The thickness of the oxide film that formed on sample surface was increased with the salt spray duration, and somewhat it could act as lubrication during the fretting wear process; however, the corrosive chloride would accelerate the fretting mechanical damage behavior.

In a salt steam spray condition, the fretting tribo-corrosion behaviors of Inconel 690 alloy surface was studied.

This experimental study aims to deal with the improvement of process performance of electric discharge drilling (EDD) for fabricating true blind holes in titanium alloy Ti6Al4V. Micro EDD was performed on Ti6Al4V and blind holes were drilled into the workpiece.

The effects of input parameters (i.e. voltage, capacitance and spindle speed) on responses (i.e. material removal rate, tool wear rate and surface roughness [SR]) were evaluated through response surface methodology. The data was analyzed using analysis of variance and multi-optimization was performed for the optimized set of parameters. The optimized process parameters were then used to drill deeper blind holes.

Blind holes have few characteristics such as SR, taper angle and corner radius. The value of corner radius reflects the quality of the hole produced as well as the amount of tool roundness. The optimized process parameters suggested by the current experimental study lower down the response values (i.e. SR, taper angle and corner radius). The process is found very effective in producing finished blind holes.

This experimental study establishes EDD as a feasible process for the fabrication of truly blind holes in Ti6Al4V.

This study aims to comparatively analyze the cut parts obtained as a result of cutting the Ni-based Inconel 625 alloy, which is widely used in the aerospace industry, with the wire electro-discharge machining (WEDM) and abrasive water jet machining (AWJM) methods in terms of macro- and microanalyses.

In this study, calipers, Mitutoyo SJ-210, Nikon SMZ 745 T, scanning electron microscope and energy dispersive X-ray were used to determine kerf, surface roughness and macro- and microanalyses.

Considering the applications in the turbine industry, it has been determined that the WEDM method is suitable to meet the standards for the machinability of Inconel 625 alloy. In contrast, the AWJM method does not meet the standards. Namely, while the kerf angle was formed because the hole entrance diameters of the holes obtained with AWJM were larger than the hole exit diameters, the equalization of the hole entry and exit dimensions, thanks to the perpendicularity and tension sensitivity of the wire electrode used in the holes drilled with WEDM ensured that the kerf angle was not formed.

It is known that the surface roughness of the parts used in the turbine industry is accepted at Ra = 0.8 µm. In this study, the average roughness value obtained from the successful drilling of Inconel 625 alloy with the WEDM method was 0.799 µm, and the kerf angle was obtained as zero. In the cuts made with the AWJM method, thermal effects such as debris, microcracks and melted materials were not observed; an average surface roughness of 2.293 µm and a kerf of 0.976° were obtained.

This paper aims to study the influence of microparticles on the surface cavitation behavior of 2Cr3WMoV steel; microparticle suspensions of different concentration, particle size, material and shape were prepared based on ultrasonic vibration cavitation experimental device.

2Cr3WMoV steel was taken as the research object for ultrasonic cavitation experiment. The morphology, quantity and distribution of cavitation pits were observed and analyzed by metallographic microscope and scanning electron microscope.

The study findings showed that the surface cavitation process produced pinhole cavitation pits on the surface of 2Cr3WMoV steel. High temperature in the process led to oxidation and carbon precipitation on the material surface, resulting in the “rainbow ring” cavitation morphology. Both the concentration and size of microparticles affected the number of pits on the material surface. When the concentration of microparticles was 1 g/L, the number of pits reached the maximum, and when the size of microparticles was 20 µm, the number of pits reached the minimum. The microparticles of Fe3O4, Al2O3, SiC and SiO2 all increased the number of pits on the surface of 2Cr3WMoV steel. In addition, the distribution of pits of spherical microparticles was more concentrated than that of irregularly shaped microparticles in turbidity.

Most of the current studies have not systematically focused on the effect of each factor of microparticles on the cavitation behavior when they act separately, and the results of the studies are more scattered and varied. At the same time, it has not been found to carry out the study of microparticle cavitation with 2Cr3WMoV steel as the research material, and there is a lack of relevant cavitation morphology and experimental data.

This study aims to investigate the fatigue crack propagation behavior of SiC particle-reinforced 2124 Al alloy composites under constant amplitude axial loading at a stress ratio of R = 0.1. For this purpose, it is performed experiments and comparatively analyze the results by producing 5, 10, 15 Vol.% SiCp-reinforced composites and unreinforced 2124 Al alloy billets with powder metallurgy (PM) production technique.

With the PM production technique, SiCp-reinforced composite and unreinforced 2124 Al alloy billets were produced at 5%, 10%, 15% volume ratios. After the produced billets were extruded and 5 mm thick plates were formed, tensile and fatigue crack propagation compact tensile (CT) samples were prepared. Optical microscope examinations were carried out to determine the microstructural properties of billet and samples. To determine the SiC particle–matrix interactions due to the composite microstructure, unlike the Al alloy, which affects the crack initiation life and crack propagation rate, detailed scanning electron microscopy (SEM) studies have been carried out.

Optical microscope examinations for the determination of the microstructural properties of billet and samples showed that although SiC particles were rarely clustered in the Al alloy matrix, they were generally homogeneously dispersed. Fatigue crack propagation rates were determined experimentally. While the highest crack initiation resistance was achieved at 5% SiC volume ratio, the slowest crack propagation rate in the stable crack propagation region was found in the unreinforced 2124 Al alloy. At volume ratios greater than 5%, the number of crack initiation cycles decreases and the propagation rate increases.

As a requirement of damage tolerance design, the fatigue crack propagation rate and fatigue behavior of materials to be used in high-tech vehicles such as aircraft structural parts should be well characterized. Therefore, safer use of these materials in critical structural parts becomes widespread. In this study, besides measuring fatigue crack propagation rates, the mechanisms causing crack acceleration or deceleration were determined by applying detailed SEM examinations.

This study aimed to examine the antecedents, correlates, and consequences of burnout among higher education faculty in Saudi Arabia using the theoretical framework of the job demands-resources model.

Using a quantitative research design, a cross-sectional survey was employed to collect data from faculty members across multiple Saudi universities. The constructs were measured using validated scales, and data analysis included exploratory factor analysis, Pearson correlation analysis, factorial ANOVA, and multiple regression.

The study identified moderate levels of burnout, confirming a significant positive relationship with role conflict and a negative relationship with internal locus of control. Burnout significantly contributed to depression, insomnia, and turnover intentions. However, no significant relationship was found between burnout and workplace conflict when controlling for other variables.

The study's findings can inform policymakers and academic administrators about measures to alleviate faculty burnout, thus contributing to healthier academic work environments aligned with Saudi Arabia's Vision 2030 goals.

This research extends the job demands-resources model within the context of higher education institutions in Saudi Arabia, offering nuanced insights into burnout dynamics among university faculty in this region. Despite the model's robustness, the absence of a significant relationship between burnout and workplace conflict signals the need for a more intricate understanding of burnout's antecedents and consequences.

This paper investigates the consequences of job insecurity among hotel employees during the COVID-19 pandemic.

Data were obtained from the employees of two five-star chain hotels in Turkey. The study hypotheses were tested via structural equation modeling.

The research findings demonstrate that job insecurity exacerbates job tension. Job tension erodes employees’ trust in organization and aggravates their propensity to leave work early and be late for work. As hypothesized, job tension mediates the effect of job insecurity on organizational trust and the abovementioned outcomes.

This study adds to the hospitality literature by assessing the interrelationships of job insecurity, job tension, organizational trust and nonattendance intentions.