Search results

The purpose of this study is to form fabrication and electrical characteristics of passive device embedded substrate that is embedded chip bead inductor and chip capacitor inside substrate for the application of radio frequency (RF) modules.

Passive device embedded substrate was fabricated using embedding process that consists of lamination process, laser drilling at the electrode Cu pads of passive components, electro-less Cu plating formation process such as photolithography, electrolytic Cu plating and etching. Impedance and capacitance characteristics of the fabricated passive device embedded substrate were evaluated.

By checking what embedded components are placed in the appropriate place using failure analysis via connection performance between copper plane and embedded components was verified. For measuring electrical characteristics of the fabricated passive device embedded substrate, the evaluation was done using test methods like continuity test for checking interconnections which are not connected to any embedded components and in-circuit test for checking interconnections which are connected to any embedded component. From in-circuit testing for embedding passive components with series and parallel circuits, the authors verified how to test passive device embedded substrate by using capacitance and impedance measurement with the comparison of measured results between good samples and bad samples.

Ultra miniaturized and low-profile mobile products are driving the need for embedded passive component integration technologies using a novel manufacturing-compatible organic substrate and interconnect technologies. Fabrication and test methods for passive device embedded substrate described in this paper are expected to lead to be developed to make quality measurable for the application of RF modules.

With the advent of new materials and technologies that enable passive components to be embedded within electronic substrates, one key question that arises is: under what circumstances (and for what type of applications) is it economically viable to consider using embedded passives? The economic issues that must be considered consist of a combination of manufacturing costs and throughputs, and non‐manufacturing life cycle costs. This paper discusses the assessment of manufacturing costs associated with embedding resistors and capacitors in printed circuit boards and provides cost modeling results for an avionics board. The discussion is extended to include optimizing the specific embedded passive content in a board and design for production modeling when embedded passives are present. Life cycle cost issues are also qualitatively discussed.

Embedded passives account for a very large part of today's electronic assemblies. This is particularly true for products such as cellular phones, camcorders, computers, and several critical defence devices. Market pressures for new products with more features, smaller size and lower cost demand smaller, compacter, simpler substrates. An obvious strategy is to reduce the number of surface mounted passives by embedding them in the substrate. In addition, current interconnect technology to accommodate surface mounted passives imposes certain limits on board design which constrain the overall system speed. Embedding passives is one way to minimize the functional footprint while at the same time improving performance. The purpose of this paper is to describe the development of a thin film technology based on ferroelectric‐epoxy polymer‐based flake‐free resin coated copper capacitive (RC3) nanocomposites to manufacture multilayer embedded capacitors.

This paper discusses thin film technology based on RC3 nanocomposites. In particular, recent developments in high capacitance, large area, thin film passives, and their integration in system in a package (SiP) are highlighted.

A variety of RC3 nanocomposite thin films ranging from 8 to 50 microns thick were processed on copper substrates by liquid coating. Multilayer embedded capacitors resulted in high capacitances of 16‐28 nF. The fabricated test vehicle also included two embedded resistor layers with resistances in the range of 15 Ω to 100 kΩ. To enable high performance devices, an embedded resistor must meet certain tolerances. The embedded resistors can be laser trimmed to a tolerance of <5 percent, which is usually acceptable for most applications. An extended embedded passives solution has been demonstrated, both through its high wireability designs and package performance, to be perfectly suited for SiP applications.

This case study designed and fabricated an eight layer high density internal passive core and subsequently applied fine geometry three buildup layers to form a 3‐8‐3 structure. The passive core technology is capable of providing up to six layers of embedded capacitance and could be extended further.

A thin film technology based on ferroelectric‐epoxy polymer‐based flake‐free RC3 nanocomposites was developed to manufacture multilayer embedded capacitors. The overall approach lends itself to package miniaturization because capacitance can be increased through multiple layers and reduced thickness to give the desired values in a smaller area.

The purpose of this paper is to investigate the basic functional parameters of passive embedded components in printed circuit boards (PCBs) under environmental exposures such as thermal-humidity and thermal exposure.

The investigations were based on the thin-film resistors made of NiP alloy, thick-film resistors made of carbon or carbon–silver inks, embedded capacitors made of FaradFlex materials and embedded inductor made in various configurations. The capacitors and thin- and thick-film resistors were tested in the climatic chamber in conditions of thermal-humidity exposure at 85°C and 85 per cent RH for 500 h. The embedded inductors were tested in two different environmental conditions: thermal-humidity exposure at 60°C and 95 per cent RH, and thermal exposure at 150°C and additionally at the temperature in the range of +25°C to +150°C.

Studies show that in the case of embedded capacitors, the changes caused by exposure to thermal-humidity are durable and lead to the capacity increase. The embedded thin-film resistors behave in the same manner, whereas the thick-film resistors were the least resistant to the conditions of exposure. Most of the polymer thick-film resistors have been damaged. The changes of coils' properties during aging are small, and what is most important is that, after some time of exposure, their parameters stabilize at a particular level. The changes resulting from the increase in temperature are typically related to the change of material resistance (Cu) of which coils are made, and as such, they cannot be avoided but they can be predicted.

The realized studies allowed determination of the properties of the embedded passive elements with respect to specific environmental exposures. The studies show that embedded resistors can be used interchangeably with chip passive elements. It allows saving the area on the surface of PCB, occupied by these passive elements, for assembly of active elements integrated circuits (ICs) and thus enabling the miniaturization of electronic devices.

The knowledge about the behavior of the operating parameters of embedded components, considering the environmental conditions, allows for development of more complex systems with integrated PCBs.

The purpose of this paper is to investigate the behavior of embedded passives under changing temperature conditions. Influence of different temperature changes on the basic properties of embedded passives was analyzed. The main reason for these investigations was to determine functionality of passives for space application.

The investigations were based on the thin-film resistors made of Ni-P alloy, thick-film resistors made of carbon or carbon-silver inks, embedded capacitors made of FaradFlex materials and embedded inductor made in various configurations. Prepared samples were examined under the influence of a constant elevated temperature (100, 130 or 160°C) in a long period of time (minimum of 30 h), thermal cycles (from −40 to +85°C) or thermal shocks (from −40 to +105°C or from −40 to +125°C).

The achieved results revealed that resistance drift became bigger when the samples were treated at a higher constant temperature. At the same time, no significant difference in change in electrical properties for 50 and 100 Ω resistors was noticed. For all the tests, resistance change was below 2 per cent regardless of a value of the tested resistors. Conducted thermal shock studies indicate that thin-film resistors, coils and some thick-film resistors are characterized by minor variations in basic parameters. Some of the inks may show considerable resistance variations with temperature changes. Significant changes were also exhibited by embedded capacitors.

The knowledge about the behavior of the operating parameters of embedded components considering environmental conditions allow for development of more complex systems with integrated printed circuit boards.

The purpose of this paper is to investigate the influence of parameters of embedded resistive elements manufacturing process as well as the influence of environmental factors on their electrical resistance. The investigations were made in comparison to the similar constructions of discrete chip resistors assembled to standard printed circuit boards (PCBs).

The investigations were based on the thin-film resistors made of NiP alloy, thick-film resistors made of carbon or carbon-silver inks as well as chip resistors in 0402 and 0603 packages. The polymer thick-film resistive films were screen-printed on the several types finishing materials of contact terminations such as copper, silver, and gold. To determine the sensitivity of embedded resistors versus standard assembled chip resistors on environmental exposure, the climatic chamber was used. The measurements of resistance were carried out periodically during the tests, and after the exposure cycles.

The results show that the change of electrical resistance of embedded resistors, in dependence of construction and base material, is different and mainly not exceed the range of 3 per cent. The achieved results in reference to thin-film resistors are comparable with results for standard chip resistors. However, the results that were obtained for thick-film resistors with Ag and Ni/Au contacts are similar. It was not found the big differences between resistors with and without conformal coating.

The studies show that embedded resistors can be used interchangeably with chip resistors. It allows to save the area on the surface of PCB, occupied by these passive elements, for assembly of active elements (ICs) and thus enable to miniaturization of electronic devices. But embedding of passive elements into PCB requires to tackle the effect of each forming process steps on the operational properties.

The technique of passive elements embedding into PCB is generally known; however, there are no detailed reports on the impact of individual process steps and environmental conditions on the stability of their electrical resistance. The studies allow to understand the importance of each factor process and the mechanisms of operational properties changes depending on the used materials.

Numerical modelling is used to predict the thermal behaviour of embedded passive components in multi‐layer PCBs. A three‐signal layer PCB, containing embedded resistors of dimensions 0.3 6 0.3mm and thickness 0.1μm, is used to generate thermal design rules that can be applied to a wide range of PCB structures containing embedded passive components. A software package using the design rules can then make fast predictions on the thermal behaviour of heat‐generating components inside such structures.

The purpose of this study is to design and fabricate a simple passive sensor circuitry embedded into a printed circuit board (PCB) and then to examine its properties.

A passive sensor transponder integrated circuit (IC) working in the high frequency (HF) 13.56 MHz frequency band was selected for this study. A loop antenna was designed to make the reported sensor circuitry readable. Next, the sensor circuitry was fabricated and embedded into a PCB with the proposed technologies. Finally, properties of the embedded structures were examined as well-functional parameters of the sensor circuitries.

The described investigation results confirmed that the proposed technologies using an epoxy resin or standard materials used for PCB’s production allowed to successfully produce sensors embedded into PCBs. This technology did not have a negative significant impact either on quality of solder joints of the assembled transponder IC or on functional properties of the embedded sensor. Apart from the identification data, the reported sensor can provide information about a selected property of its environment, e.g. temperature when its internal temperature sensitive element is used or other factors with the use of external sensitive elements, such as humidity.

It is planned to carry on the reported investigations to examine other types of sensor circuitries capable of indicating e.g. humidity level and to evaluate influence of the proposed technology on their functional properties.

The reported sensor circuitries can be successfully used in electronic industry in internet of things systems not only to identify monitored electronic devices, but also to control selected parameters of external environment. This creates opportunity to detect device malfunction by detecting local temperature growth or to analyze its environment, which might allow to predict failure of controlled products using radio waves. This advantage seems to be extremely beneficial for applications, such as space, aviation or military, in which embedded sensor systems may lead to enhancing reliability of electronic devices by reacting on occurred failures in a more efficient way.

This study demonstrates valuable information for engineers conducting research on sensor components embedded into PCBs. The reported technologies are quite simple and cost-effective because of the use of standard materials known for PCB’s production or an epoxy resin which could be treated as an additional encapsulant material enhancing mechanical properties of the embedded sensor transponder IC.

Particularly during the past ten years, the mobile communications industry has grown by orders of magnitude, fueled by digital and RF circuit fabrication improvements, new large scale circuit integration, and other miniaturization technologies that make portable equipment smaller, cheaper, and more reliable. A key area within the telecommunication industry covers base stations and switch systems. Communications providers now require systems that provide significantly increased switching capacity. Combining both increased capability with size reduction is resulting in smaller printed circuit boards (PCBs) with more components placed on them. A potential solution to this is to embed some of the components within the board. The components which would be suitable for such a transition would be passives such as resistors, capacitors and inductors. This paper describes the work done in designing and manufacturing a PCB for the telecommunications industry with embedded resistors and microvias.