Search results

In order to investigate the vibration reduction properties of a three-dimensional elastic metastructure with spherical cavities at low frequencies.

The bandgap characteristics of a three-dimensional elastic metastructure with spherical cavities are studied based on analytical and numerical approaches.

The results of both method revealed that the vibration of the vertexes masses is important for opening bandgaps. The fact that the big sphere cavity radius or short side length of the cube unit leads to a wider bandgap, is noteworthy.

This research provides theoretical guidance for realizing the vibration attenuation application of EMs in practical engineering.

The main purpose of this paper is to investigate the vibration isolation performance of a quasi-zero stiffness (QZS) metastructure by employing the band gap (BG) mechanism.

The metastructure QZS characteristic was investigated through static analysis by numerical simulation. Based on that, the BG mechanism is primarily used in this article to investigate the wave propagation characteristics of this structure. The model's dispersion relation is then examined using theoretical (perturbation method) and finite element techniques. The dynamic response of the finite-size systems and experimental analysis is used to confirm the vibration mitigation property under investigation. Finally, the model's ability to absorb energy was examined and contrasted with a traditional model.

The analytical analysis reveals the dispersion curve and the effect of the nonlinear parameter on the curve shifting. The dispersion curve in the finite element method (FEM) result depicts five complete BGs within the range of 0–1,000 Hz, and the BG width accounted for 67.4% of the frequency concerned (0–1,000 Hz). Eigenmodes of the dispersion curves were analyzed to investigate the BG formation mechanisms. The dependence of BG opening and closure on structure parameters was also studied. Finally, the energy absorption property of the QZS metastructure was evaluated by comparing it with a classical model. The QZS structure absorbs 4.08 J/Kg compared to the 3.69 J/Kg absorbed by the classical model, which reveals that the QZS demonstrates better energy absorption performance. Based on the BG mechanism, it is clear that this model is an excellent vibration isolator, and the study reveals the frequencies at which complete vibration mitigation is achieved. As a result, this model could be a promising candidate for vibration mitigation engineering structures and energy absorption.

The tough vibration issue, which is primarily experienced in mechanical equipment, will be resolved in this study. This study provides a precise understanding of the QZS metastructure's isolation of vibration, including the frequencies at which this isolation occurs.

The purpose of this paper is to present an optimisation of four-point star-shaped structures produced through additive manufacturing (AM) polylactic acid (PLA). The study also aims to investigate the compression failure mechanism of the structure.

A Taguchi L₉ orthogonal array design of the experiment is adopted in which the input parameters are resolution (0.06, 0.15 and 0.30 mm), print speed (60, 70 and 80 mm/s) and bed temperature (55°C, 60°C, 65°C). The response parameters considered were printing time, material usage, compression yield strength, compression modulus and dimensional stability. Empirical observations during compression tests were used to evaluate the load–response mechanism of the structures.

The printing resolution is the most significant input parameter. Material length is not influenced by the printing speed and bed temperature. The compression stress–strain curve exhibits elastic, plateau and densification regions. All the samples exhibit negative Poisson’s ratio values within the elastic and plateau regions. At the beginning of densification, the Poisson’s ratios change to positive values. The metamaterial printed at a resolution of 0.3 mm, 80 mm/s and 60°C exhibits the best mechanical properties (yield strength and modulus of 2.02 and 58.87 MPa, respectively). The failure of the structure occurs through bending and torsion of the unit cells.

The optimisation study is significant for decision-making during the 3D printing and the empirical failure model shall complement the existing techniques for the mechanical analysis of the metamaterials.

To the best of the authors’ knowledge, for the first time, a new empirical model, based on the uniaxial load response and “static truss concept”, for failure mechanisms of the unit cell is presented.

The present paper aims at the multi-objective optimization of a reentrant hexagonal cell auxetic structure. In addition, a parametric analysis will be carried out to verify how each of the design factors impact each of the responses.

The multi-objective optimization of five different responses of an auxetic model was considered: mass, critical buckling load under compression effort, natural frequency, Poisson's ratio and failure load. The response surface methodology was applied, and a new meta-heuristic of optimization called the multi-objective Lichtenberg algorithm was applied to find the optimized configuration of the model. It was possible to increase the failure load by 26.75% in compression performance optimization. Furthermore, in the optimization of modal performance, it was possible to increase the natural frequency by 37.43%. Finally, all 5 responses analyzed simultaneously were optimized. In this case, it was possible to increase the critical buckling load by 42.55%, the failure load by 28.70% and reduce the mass and Poisson's ratio by 15.97 and 11%, respectively. This paper addresses something new in the scientific world to date when evaluating in a multi-objective optimization problem, the compression and modal performance of an auxetic reentrant model.

It was possible to find multi-objective optimized structures. It was possible to increase the critical buckling load by 42.82%, and the failure load in compression performance by 26.75%. Furthermore, in the optimization of modal performance, it was possible to increase the natural frequency by 37.43%, and decrease the mass by 15.97%. Finally, all 5 responses analyzed simultaneously were optimized. In this case, it was possible to increase the critical buckling load by 42.55%, increase the failure load by 28.70% and reduce the mass and Poisson's ratio by 15.97 and 11%, respectively.

There is no work in the literature to date that performed the optimization of 5 responses simultaneously of a reentrant hexagonal cell auxetic structure. This paper also presents an unprecedented statistical analysis in the literature that verifies how the design factors impact each of the responses.

The authors examined the numerical natural frequency analysis of a 2D functionally graded (FG) truncated thick hollow cone using 3D elasticity theory.

The material properties of the 2D-FGM (two dimensional-functionally graded materials) cone are graded along the radial and axial axes of the cone using a power–law distribution. The eigenvalue problem was solved using finite element analysis (FEA) employing graded hexahedral elements, and the verification of the finite element approach was assessed by comparing the current solution to earlier experimental studies.

The effects of semivertex angle, material distribution and the cone configuration on the natural frequencies have been analyzed. For various semivertex angles, thickness, length and power law exponents, many results in the form of natural frequencies and mode shapes are presented for the 2D-FGM cone. As a result, the effects of the given parameters were addressed, and the results were compared, demonstrating the direct efficiency of raising the power–law exponents and cone thickness on the rise of natural frequencies.

For the first time, the numerical natural frequency analysis of a 2D-FG truncated thick hollow truncated cone based on 3D equations of elasticity has been investigated. The material properties of the truncated cone have been distributed along two directions, which has not been considered before in any research for the truncated thick cone. The reason for using these innovative volume fraction functions is the lack of accurate coverage by functions that are available in the literature (Asemi et al., 2011; Babaei et al. 2021).

This paper aims to propose a design method for attenuating stress waves pressure using soft matrix embedded with particles.

Based on the phononic crystal theory, the particle composed of hard core and soft coating can form a spring oscillator structure. When the frequency of the wave is close to the resonance frequency of the spring oscillator, it can cause the resonance of the particle and absorb a lot of energy. In this paper, the resonant phononic crystal with three phases, namely, matrix, particle core and coating, is computationally designed to effectively mitigate the stress wave with aperiodic waveform.

The relationship between the center frequency and width of the bandgap and the geometric and physical parameters of particle core are discussed in detail, and the trend of influence is analyzed and explained by a spring oscillator model. Increasing the radius of hard core could effectively enhance the bandgap width, thus enhancing the effect of stress wave attenuation. In addition, it is found that when the wave is in the bandgap, adding viscosity into the matrix will not further enhance the stress attenuation effect, but will make the stress attenuation effect of the material worse because of the competition between viscous dissipation mechanism and resonance mechanism.

This study will provide a reference for the design of stress wave protection materials with general stress waves.

This study proposes a design method for attenuating stress waves pressure using soft matrix embedded with particles.

The fused filament fabrication (FFF) process is an additive manufacturing technique used in engineering design. The mechanical properties of parts manufactured by FFF are influenced by the printing parameters. The mechanical properties of rigid thermoplastics for FFF are well defined, while thermoplastic elastomers (TPE) are uncommonly investigated. The purpose of this paper is to investigate the influence of extruder temperature, bed temperature and printing speed on the mechanical properties of a thermoplastic elastomer.

Regression models predicting mechanical properties as a function of extruder temperature, bed temperature and printing speed were developed. Tensile specimens were tested according to ASTM D638. A 3×3 full factorial analysis, consisting of 81 experiments and 27 printing conditions was performed, and models were developed in Minitab. Tensile tests verifying the models were conducted at two selected printing conditions to assess predictive capability.

Each mechanical property was significantly affected by at least two of the investigated FFF parameters, where printing speed and extruder temperature terms influenced all mechanical properties (p < 0.05). Notably, tensile modulus could be increased by 21%, from 200 to 244 MPa. Verification prints exhibited properties within 10% of the predictions. Not all properties could be maximized together, emphasizing the importance of understanding FFF parameter effects on mechanical properties when making design decisions.

This work developed a model to assess FFF parameter influence on mechanical properties of a previously unstudied thermoplastic elastomer and made property predictions within 10% accuracy.

Honeycombs enjoy wide use in various engineering applications. The emergence of additive manufacturing (AM) as a method of customisable of parts has enabled the reinvention of the honeycomb structure. However, research on in-plane compressive performance of both classical and new types of honeycombs fabricated via AM is still ongoing. Several important findings have emerged over the past years, with significance for the AM community and a review is considered necessary and timely. This paper aims to review the in-plane compressive performance of AM honeycomb structures.

This paper provides a state-of-the-art review focussing on the in-plane compressive performance of AM honeycomb structures, covering both polymers and metals. Recently published studies, over the past six years, have been reviewed under the specific theme of in-plane compression properties.

The key factors influencing the AM honeycombs' in-plane compressive performance are identified, namely the geometrical features, such as topology shape, cell wall thickness, cell size and manufacturing parameters. Moreover, the techniques and configurations commonly used for geometry optimisation toward improving mechanical performance are discussed in detail. Current AM limitations applicable to AM honeycomb structures are identified and potential future directions are also discussed in this paper.

This work evaluates critically the primary results and findings from the published research literature associated with the in-plane compressive mechanical performance of AM honeycombs.

The purpose of this paper is to focus on the emerging phenomenon of medical tourism in the context of Iran from a customer experience management perspective and benchmark of their judgment including positive or negative, of the experience they have achieved of the Iranian health (medical) experience (CE) and suggest scenarios for the improvement of the Iranian customer experience management (CEM).

The research methodologies and research methods that are used in this descriptive-analytical research are based on an inspection of the remarkable literature related to medical tourism and customer experience management. The data gathering instrument is a researcher-made questionnaire based on the variables in the conceptual model extracted from the research literature. The study was conducted from May to August 2019. The population cohort of this study was the foreign patients calling selected Iranian hospitals and the sampling method was a purposive and snowball sample of prospective medical tourists. As the study was conducted throughout Iran, some important hospitals in Iran were selected by stratified sampling Yang et al. (2020b). The sample size and data saturation were 500 participants Lv and Song (2019). The collected data using the questionnaire were analyzed by SPSS software and statistical tests.

According to the results, the customer experience management statistical significance in the task aspect is (p = 0.0523), in the mechanical aspect is (p = 0.0563), in the human aspect is (p = 0.0544). The study showed positive customer experience among the patients who had been treated in the Iranian hospitals.

There is a lack of study that focuses on medical tourism and customer experience management in Iran. Therefore, based on the results of this study, the experience of medical tourists in Iran proved to be positive and satisfying. As little research has been conducted in the area of customer experience management (CEM) in Iranian medical tourism, future researchers can use these valuable results precisely and in more detail to benchmark more accurately the customer experience in all areas of medical and health tourism and other research areas in different aspects of CEM in Iran.

The mesoscale structure (MS) has a significant impact on the mechanical performance of parts made by additive manufacturing (AM). This paper aims to explore the design and fabrication of force-flow guided reinforcement mesoscale structure (FFRMS) compared with the homogeneous mesoscale structure (HMS), which is inconsistent with the stress field for a given load condition. Some cases were presented to demonstrate the mechanical properties of FFRMS in terms of MS combined with quasi-isotropy and anisotropy.

The paper consists of four main sections: the first developed the concept of FFRMS design based on HMS, the second explored volume fraction control for the proportion of force-flow lines in terms of mechanical property requirement, and the third presented a sequence stacking theory and practical manufacturing process framework and the final sections provided some application case studies.

The main contributions of this study were the definition and development of the FFRMS concept, the application framework and the original case studies. As an example, a typical lug designed with the proposed FFRMS method was fabricated by three different AM processes. The test results showed that both the strength and stiffness of the specimens are improved greatly by using the FFRMS design method.

The superposition of HMS as the basement and force-flow as an indication of the stiffener, leading to a heterogeneous structure, which exhibits more efficient and diversified means compared with the traditional way of increasing the HMS density merely.