Search results

This paper comprehensively addresses the influence of chopped strand mat glass fiber-reinforced polymer (GFRP) patch configurations such as geometry, dimensions, position and the number of layers of patches, whether a single or double patch is used and how well debonding the area under the patch improves the strength of the cracked aluminum plates with different crack lengths.

Single-edge cracked aluminum specimens of 150 mm in length and 50 mm in width were tested using the tensile test. The cracked aluminum specimens were then repaired using GFRP patches with various configurations. A three-dimensional (3D) finite element method (FEM) was adopted to simulate the repaired cracked aluminum plates using composite patches to obtain the stress intensity factor (SIF). The numerical modeling and validation of ABAQUS software and the contour integral method for SIF calculations provide a valuable tool for further investigation and design optimization.

The width of the GFRP patches affected the efficiency of the rehabilitated cracked aluminum plate. Increasing patch width WP from 5 mm to 15 mm increases the peak load by 9.7 and 17.5%, respectively, if compared with the specimen without the patch. The efficiency of the GFRP patch in reducing the SIF increased as the number of layers increased, i.e. the maximum load was enhanced by 5%.

This study assessed repairing metallic structures using the chopped strand mat GFRP. Furthermore, it demonstrated the superiority of rectangular patches over semicircular ones, along with the benefit of using double patches for out-of-plane bending prevention and it emphasizes the detrimental effect of defects in the bonding area between the patch and the cracked component. This underlines the importance of proper surface preparation and bonding techniques for successful repair.

This study investigates the behavior of viscous hybrid ferromagnetic fluids flowing through plain elastic sheets with the magnetic polarization effect. It examines flow in a porous medium using Stefan blowing and utilizes a versatile hybrid ferrofluid containing MnZnFe₂O₄ and Fe₃O₄ nanoparticles in the C2H2F4 base fluid, offering potential real-world applications. The study focuses on steady, laminar and viscous incompressible flow, analyzing heat and mass transfer aspects, including thermal radiation, Brownian motion, thermophoresis and viscous dissipation with convective boundary condition.

The governing expression of the flow model is addressed with pertinent non-dimensional transformations, and the finite element method solves the obtained system of ordinary differential equations.

The variations in fluid velocity, temperature and concentration profiles against all the physical parameters are analyzed through their graphical view. The association of these parameters with local surface friction coefficient, Nusselt number and Sherwood number is examined with the numerical data in a table.

This work extends previous research on ferrofluid flow, investigating unexplored parameters and offering valuable insights with potential engineering, industrial and medical implications. It introduces a novel approach that uses mathematical simplification techniques and the finite element method for the solution.

Three-dimensional (3D) casting means using additive manufacturing (AM) techniques to print the mould for casting the cast tool. The printed mould, however, should be checked for its dimensional accuracy. 3D scanning can be used for the same. The purpose of this study is to combine the different AM techniques for 3D casting with 3D scanning to produce parts with close tolerance for preparing electrical discharge machining (EDM) electrodes.

The four processes, namely, stereolithography, selective laser sintering, fused deposition modelling and vacuum casting, are used to print the casting mould. The mould is designed in two halves, assembled to form a complete mould. The mould is 3D scanned in two stages: before and after using it as a casting mould. The mould's average and maximum dimensional deviations are calculated using 3D-scanned results. The eutectic Sn-Bi alloy is cast in the mould. The surface roughness of the mould and the cast tool are measured.

The cast tool is selected from the four processes in terms of dimensional accuracy and surface finish. The same is electroplated with copper. The microstructure of the cast tool (low-melting-point alloy) and deposited copper is analysed using a scanning electron microscope. Energy dispersive spectroscopy and X-ray diffraction techniques are used to verify the composition of the cast and coated alloy. The electroplated tool is finally tested on the EDM setup. The material removal rate and tool wear are measured. The performance is compared with a solid copper tool. The free-form customised EDM mould is also prepared, and the profile is cast out. The same is tested on the EDM. Thus, the developed path can be successfully used for rapid tooling applications.

The eutectic composition of Sn-Bi is cast in the 3D-printed mould using different AM techniques combined with 3D scanning quality to check its feasibility as an EDM electrode, which is a novel work and has not been done previously.

This study investigates the coupling effects between temperature, permeability and stress fields during the development of geothermal reservoirs, comparing the impacts of inter-well pressure differentials, reservoir temperature and heat extraction fluid on geothermal extraction.

This study employs theoretical analysis and numerical simulation to explore the coupling mechanisms of temperature, permeability and stress fields in a geothermal reservoir using a thermal-hydrological-mechanical (THM) three-field coupling model.

The results reveal that the pressure differential between wells significantly impacts geothermal extraction capacity, with SC-CO2 achieving 1.83 times the capacity of water. Increasing the aperture of hydraulic and natural fractures effectively enhances geothermal production, with a notable enhancement for natural fractures.

The research provides a critical theoretical foundation for understanding THM coupling mechanisms in geothermal extraction, supporting the optimization of geothermal resource development and utilization.

This paper aims to investigate the corrosion kinetics and corrosion behavior of NdFeB magnets with the addition of heavy rare earth dysprosium (Dy) for its inhibitory activity on poor corrosion resistance of NdFeB magnets.

To study the effect of dysprosium addition on corrosion behavior of NdFeB magnets and investigate its mechanism, potentiodynamic polarization, scanning electron microscopy (SEM), electrochemical impedance, energy dispersion spectrum (EDS) and scanning Kelvin probe force microscopy (SKPFM) were applied in the research. Besides, microstructures were observed by SEM equipped with EDS. Atomic force microscopy was introduced to analyze the morphology, potential image as well as the contact potential difference. The SKPFM mapping scan was applied to obtain the contact potential around Nd-rich phase at 0.1 Hz. The magnets were detected via X-ray diffraction.

Substitution of Nd with Dy led to improvement of corrosion resistance and reduced the potential difference between matrix and Nd-rich phase. Corrosion resistance is Nd-rich phase < the void < metal matrix; maximum potential difference between matrix and Nd-rich phase of Dy = 0, Dy = 3 and Dy = 6 Wt.% is 411.3, 279.4 and 255.8 mV, respectively. The corrosion rate of NdFeB magnet with 6 Wt.% Dy is about 67% of that without Dy at steady corrosion stage. The addition of Dy markedly enhanced the corrosion resistance of NdFeB magnets.

This research innovatively investigates the effect of adding heavy rare earth Dy to NdFeB permanent magnets on magnetic properties, as well as their effects on microstructure, phase structure and most importantly on corrosion resistance. Most scholars are studying the effect of element addition on magnetic properties but not on corrosion resistance. This paper creatively fills this research gap. NdFeB magnets are applied in smart cars, robotics, AI intelligence, etc. The in-depth research on corrosion resistance by adding heavy rare earths has made significant and outstanding contributions to promoting the rapid development of the rare earth industry.