Search results

The purpose of this study is to explore the effects of aerospike and hemispherical aerodisks on flow characteristics and drag reduction in supersonic flow over a blunt body. Specifically, the study aims to analyze the impact of varying the length of the cylindrical rod in the aerospike (ranging from 0.5 to 2.0 times the diameter of the blunt body) and the diameter of the hemispherical disk (ranging from 0.25 to 0.75 times the blunt body diameter). CFD simulations were conducted at a supersonic Mach number of 2 and a Reynolds number of 2.79 × 10⁶.

ICEM CFD and ANSYS CFX solver were used to generate the three-dimensional flow along with its structures. The flow structure and drag coefficient were computed using Reynolds-averaged Navier–Stokes equation model. The drag reduction mechanism was also explained using the idea of dividing streamline and density contour. The performance of the aero spike length and the effect of aero disk size on the drag are investigated.

The separating shock is located in front of the blunt body, forming an effective conical shape that reduces the pressure drag acting on the blunt body. It was observed that extending the length of the spike beyond a specific critical point did not impact the flow field characteristics and had no further influence on the enhanced performance. The optimal combination of disk and spike length was determined, resulting in a substantial reduction in drag through the introduction of the aerospike and disk.

To predict the accurate results of drag and to reduce the simulation time, a hexa grid with finer mesh structure was adopted in the simulation.

The blunt nose structures are primarily employed in the design of rockets, missiles, and re-entry capsules to withstand higher aerodynamic loads and aerodynamic heating.

For the optimized size of the aero spike, aero disk is also optimized to use the benefits of both.

This study aims to investigate the morphing concepts able to manipulate the dynamics of the downstream unsteadiness in the separated shear layers and, in the wake, be able to modify the upstream shock–boundary layer interaction (SBLI) around an A320 morphing prototype to control these instabilities, with emphasis to the attenuation or even suppression of the transonic buffet. The modification of the aerodynamic performances according to a large parametric study carried out at Reynolds number of 4.5 × 10⁶, Mach number of 0.78 and various angles of attack in the range of (0, 2.4)° according to two morphing concepts (travelling waves and trailing edge vibration) are discussed, and the final benefits in aerodynamic performance increase are evaluated.

This article examines through high fidelity (Hi-Fi) numerical simulation the effects of the trailing edge (TE) actuation and of travelling waves along a specific area of the suction side starting from practically the most downstream position of the shock wave motion according to the buffet and extending up to nearly the TE. The present paper studies through spectral analysis the coherent structures development in the near wake and the comparison of the aerodynamic forces to the non-actuated case. Thus, the physical mechanisms of the morphing leading to the increase of the lift-to-drag ratio and the drag and noise sources reduction are identified.

This study investigates the influence of shear-layer and near-wake vortices on the SBLI around an A320 aerofoil and attenuation of the related instabilities thanks to novel morphing: travelling waves generated along the suction side and trailing-edge vibration. A drag reduction of 14% and a lift-to-drag increase in the order of 8% are obtained. The morphing has shown a lift increase in the range of (1.8, 2.5)% for angle of attack of 1.8° and 2.4°, where a significant lift increase of 7.7% is obtained for the angle of incidence of 0° with a drag reduction of 3.66% yielding an aerodynamic efficiency of 11.8%.

This paper presents results of morphing A320 aerofoil, with a chord of 70cm and subjected to two actuation kinds, original in the state of the art at M = 0.78 and Re = 4.5 million. These Hi-Fi simulations are rather rare; a majority of existing ones concern smaller dimensions. This study showed for the first time a modified buffet mode, displaying periodic high-lift “plateaus” interspersed by shorter lift-decrease intervals. Through trailing-edge vibration, this pattern is modified towards a sinusoidal-like buffet, with a considerable amplitude decrease. Lock-in of buffet frequency to the actuation is obtained, leading to this amplitude reduction and a drastic aerodynamic performance increase.

An experimental investigation of hemispherical forebody interaction effects on the drag coefficient of a D-shaped model is carried out for three-dimensional flow in the subcritical range of Reynolds number 1 × 10⁵ ≤ Re ≤ 1.8 × 10⁵. To study the interaction effect, hemispherical shapes of various sizes are attached to the upriver of the D-shaped bluff body model. The diameter of the hemisphere (b₁) varied from 0.25 to 0.75 times the diameter of the D-shaped model (b₂) and its gap from the D-shaped model (g/b₂) ranged from 0.25 to 1.75 b₂.

The experiments were carried out in a low-speed open-circuit closed jet wind tunnel with test section dimensions of 1.2 × 0.9 × 1.8 m (W × H × L) capable of generating maximum velocity up to 45 m/s. The wind tunnel is equipped with a driving unit which has a 175-hp motor with three propellers controlled by a 160-kW inverter drive. Drag force is measured with an internal six-component balance with the help of the Spider 3013 E-pro data acquisition system.

The wind tunnel results show that the hemispherical forebody has a diameter ratio of 0.75 with a gap ratio of 0.25, resulting in a maximum drag reduction of 67%.

The turbulence intensity of the wind tunnel is about 5.6% at a velocity of 18 m/s. The uncertainty in the velocity and the drag coefficient measurement are about ±1.5 and ±2.83 %, respectively. The maximum error in the geometric model is about ±1.33 %.

The results from the research work are helpful in choosing the optimum spacing of road vehicles, especially truck–trailer and launch vehicle applications.

Drag reduction of road vehicle resulting less fuel consumption as well as less pollution to the environment. For instance, tractor trailer experiencing approximately 45% of aerodynamics drag is due to front part of the vehicle. The other contributors are 30% due to trailer base and 25% is due to under body flow. Nearly 65% of energy was spent to overcome the aerodynamic drag, when the vehicle is traveling at the average of 70 kmph (Seifert 2008 and Doyle 2008).

The benefits of placing the forebody in front of the main body will have a strong influence on reducing fuel consumption.

Winglets play a major role in saving fuel costs because they reduce the lift-induced drag formed at the wingtips. The purpose of this paper is to obtain the best orientation of the winglet for the Office National d’Etudes et de Recherches Aérospatiales (ONERA) M6 wing at Mach number 0.84 in terms of lift to drag ratio.

A computational fluid dynamics analysis of the wing-winglet configuration based on the ONERA M6 airfoil on drag reduction for different attack angles at Mach 0.84 was performed using analysis of systems Fluent. First, the best values of cant and sweep angles in terms of aerodynamic performance were selected by performing simulations. The analysis included cant angle values of 30°, 40°, 45°, 55°, 60°, 70° and 75°, while for the sweep angles 35°, 45°, 55°, 65° and 75° angles were used. The aerodynamic performance was measured in terms of the obtained lift to drag ratios.

The results showed that slight alternations in the winglet configuration can improve aerodynamic performance for various attack angles. The best lift to drag ratio for the winglet was achieved at a cant angle of 30° and a sweep angle of 65°, which caused a 5.33% increase in the lift to drag ratio. The toe-out angle winglets as compared to the toe-in angles caused the lift to drag ratio to increase because of more attached flow at its surface. The maximum value of the lift to drag ratio was obtained with a toe-out angle (−5°) at an angle of attack 3° which was 2.53% greater than the zero-toed angle winglet.

This work is relatively unique because the cant, sweep and toe angles were analyzed altogether and led to a significant reduction in drag as compared to wing without winglet. The wing model was compared with the results provided by National Aeronautics and Space Administration so this validated the simulation for different wing-winglet configurations.

THE possibility of applying boundary layer control by suction at the trailing edge to reduce the profile drag of a helicopter rotor blade using centrifugal forces to provide the suction was investigated. It was shown theoretically that it is possible to use this method of suction, and that it is advantageous to suck at the trailing edge if the drag reduction obtained was greater than a certain value which depended on the amount of suction. Experimental work was carried out on a model wing with different types of slots to determine the profile drag reduction possible using theoretically predicted suction flow rates. The experiments were carried out at an effective Reynolds Number based on wing chord of 0.62 x 108. It was found that a single long slot of 2 per cent chord width spanning the whole blade, as close as possible to the trailing edge on the upper surface, gave the best results. The maximum drag reduction occurred at high values of lift coefficient and was of the order of 20 per cent. Using the experimental results it was shown that a helicopter employing this type of boundary layer control would require less engine power.

Since the inception of aerospace engineering, reducing drag is of eternal importance. Over the years, researchers have been trying to improve the aerodynamics of National Advisory Committee for Aeronautics (NACA) aerofoils in many ways. It is proved that smooth-surfaced NACA 0012 aerofoil produces more drag in compressible flow. Recent research on shark-skin pattern warrants a feasible solution to many fluid-engineering problems. Several attempts were made by many researchers to implement the idea of shark skin in the form of coatings, texture and more. However, those ideas are at greater risk when it comes to wing maintenance. The purpose of this paper is to implement a relatively larger biomimetic pattern which would make way for easy maintenance of patterned wings with improved performance.

In this paper, two biomimetic aerofoils are designed by optimizing the surface pattern of shark skin and are tested at different angles of attack in the computational flow domain.

The results of the biomimetic aerofoils prove that viscous and total drag can be reduced up to 33.08% and 3.68%, respectively, at high subsonic speed when validated against a NACA 0012 aerofoil. With the ample effectiveness of patched shark-skin pattern, biomimetic aerofoil generates as high as 10.42% lift than NACA 0012.

In this study, a feasible shark-skin pattern is constructed for NACA 0012 in a transonic flow regime. Computational results achieved using the theoretical model agree with experimental data.

THE Belfast was designed and built to a specification for a long range strategic aircraft suitable for carrying heavy and bulky items of freight. The ability to airdrop supplies, combined with structural advantages, led to the choice of rear access to the freight hold; utilisation of part of the freight door as a loading ramp leads to independence of ground based freight handling equipment. The rear fuselage was up‐swept in order to provide ample head‐room for cargo on the ramp. To minimise this upsweep and also to facilitate handling of heavy loads, a low angle of inclination of the ramp is necessary. This led to a low freight floor height in relation to the ground, and to flattening of the rear fuselage undersurface. These features are illustrated in FIG. 1 which depicts the unloading of an Abbott self propelled gun carrier.

A review is attempted with the objective to indicate the most promising aeronautical technology for application to future subsonic civil transport aircraft.

A methodology is put forward, according to which direct operating costs (DOC) are examined in order to identify those that can be reduced, and, then, specific technology is assessed in relation to its efficiency in reducing these DOC, operational feasibility and cost‐effectiveness.

This assessment suggests the selection of propfan and powered lift as the leading future aeronautical technology. These findings are supported by a comparison of a number of advanced technology designs.

Provides a starting point for further investigation of advanced aeronautical technology and unconventional configurations for large subsonic civil transport aircraft.

The present work aims to analyze the feasibility of wingtip device incorporation into transport airplane configurations considering many aspects such as performance, cost and environmental impact. A design framework encompassing optimization for wing-body configurations with and without winglets is described and application examples are presented and discussed.

modeFrontier, an object-oriented optimization design framework, was used to perform optimization tasks of configurations with wingtip devices. A full potential code with viscous effects correction was used to calculate the aerodynamic characteristics of the fuselage–wing–winglet configuration. MATLAB® was also used to perform some computations and was easily integrated into the modeFrontier frameworks. CFD analyses of transport airplanes configurations were also performed with Fluent and CFD++ codes.

Winglet provides considerable aerodynamic benefits regarding similar wings without winglets. Drag coefficient reduction in the order of 15 drag counts was achieved in the cruise condition. Winglet also provides a small boost in the clean-wing maximum lift coefficient. In addition, less fuel burn means fewer emissions and contributes toward preserving the environment.

More efficient transport airplanes, presenting considerable lower fuel burn.

Among other contributions, wingtip devices reduce fuel burn, engine emissions and contribute to a longer engine lifespan, reducing direct operating costs. This way, they are in tune with a greener world.

The paper provides valuable wind-tunnel data of several winglet configurations, an impact of the incorporation of winglets on airplane design diagram and a direct comparison of two optimizations, one performed with winglets in the configuration and the other without winglets. These simulations showed that their Pareto fronts are clearly apart from each other, with the one from the configuration with winglets placed well above the other without winglets. The present simulations indicate that there are always aerodynamic benefits present regardless the skeptical statements of some engineers. that a well-designed wing does not need any winglet.

This study aims to achieve optimum flow separation control for a road vehicle using a reverse flow fan on rear side.

A full-length reverse flow fan array (fan’s air speed is 50% of the car’s speed) is attached throughout the width of the vehicle at rear edge corner.

The reverse flow fan array positioned at rear edge of car pushes the airflow against the car’s rear window. It creates the recirculation region and alters the pressure distribution. This reduces the lift coefficient by 150%, which becomes the downforce and reduces the drag coefficient by 22%. As the car speed increases, fan speed should also be increased for effective flow control.

This active flow control method for 3D Ahmed car body has been studied computationally at low speed (40 m/s).

This design increases the downforce, thus gives better cornering speed and stability, and decreases the drag which improves fuel efficiency. It can be used for effective flow control of cars (hatchback/sedan). The findings can be applied to the bluff bodies, road vehicles, UAV and helicopter fuselage for flow separation control.

The fan array is attached on car’s rear side, which blows air against the car’s rear window. It alters the pressure distribution and aerodynamics forces favorably. But the existing high-speed fan used in a sports cars sucks the air from bottom and pushes it rearward, which increases both the traction force and drag.