Search results

Use of packed beds, enhanced tubes, nano-fluids and artificial ribs are few passive techniques to increase heat transfer in solar air heaters (SAHs). Artificial ribs attached to the absorber plate of the SAH will enhance the turbulence near the plate. Experimental analyses are conducted to find the thermal performance of SAH with ribs of regular geometries including rectangular, semi-circular and triangular in cross section. This paper aims to present the improvement in thermal performance of SAH with modified-arc.

Absorber plates are designed with ribs of rectangular, triangular, semi-circular and modified-arc in cross-section using existing data in literature. Physical dimensions of the ribs are designed by adapting procedure from literature. Absorber plates are manufactured with ribs and coated with blackboard paint and fixed to the existing SAH. Experiments are conducted with a variable-speed blower fixed to the inlet section of the SAH, which is used to supply air at different mass flow rates in a range between 0.495 and 0.557 kg/min.

Efficiency is found to be a strong function of mass flow rate of air through the SAH from the present experimental investigations. It was found that use of modified-arc ribs enhanced the efficiency of SAH by 105.35 per cent compared to SAH with plane absorber plate. Efficiency of SAH with modified-arc ribs is found to be higher by 24.43, 45.61 and 63.21 per cent, respectively, for SAH with semi-circular, rectangular and triangular arc ribs on its absorber plate.

Experiments on SAH are conducted during daytime from 9:00 am to 5:00 pm in open atmospheric conditions. Solar intensity is continuously changing during the experimentation from morning to evening. Calculations are made based on the observations with average values of solar intensity and temperature readings. More accurate values of SAH efficiency can be obtained with constant heat supply to the absorber plate by simulating the experimental setup in indoor conditions. Temperature and flow rate observations could be more accurate with sophisticated instrumentation rather than using simple thermocouples and orifice meters.

SAHs are basically used to supply hot air for both rural and industrial applications. These are used for crop drying, preheating of air, removal of moisture from leather, chemicals, etc. Conventionally, formers in India are using open sun drying to remove moisture from agricultural products. In this method, the moisture can be removed up to a level of 20 to 25 per cent. Use of SAH can remove moisture up to below 5 per cent and process is clean without reducing the quality of agricultural products. Enhancing the efficiency of SAHs will surely increase its usage by formers for crop drying.

Use of artificial ribs on absorber plate of SAH is most economical among many of the active and passive techniques. Numerical and experimental investigations are found in literature with regular cross-sectional ribs, including rectangular, triangular and semi-circular. The present work proposed new shape of the ribs named as modified-arc, which was not presented in the literature. Experimental analysis proved that the use of modified-arc makes the SAH more efficient in heat transfer.

Suggests that the next civil supersonic passenger aircraft project will pose a number of challenges. The propulsion system for this aircraft will have to achieve economic operation for both supersonic and subsonic cruise modes. In addition, the current and intended noise and pollutant emissions legislation will have to be met. Suggests that, while there are a number of proposed engines for the next generation civil supersonic aircraft, they all exhibit difficulties in meeting the compromises inherent in the engine duty. Offers a novel solution based on a unique design. Discusses the underlying issues and presents the design based on retractable fans driven by a single stage double pass tip turbine.

The purpose of this study is to develop new tandem configurations of erbium-doped fiber amplifier (EDFA) using all possible pump-signal-direction schemes in simulation to identify a system configuration with the best performance in the means of the highest gain with the lowest noise figure (NF) output.

The spatial evolution of the physical properties such as gain, NF, population density and amplified spontaneous emission along the total length of the double-stage single-pass EDFA and single-stage double-pass EDFA configurations under all possible pumping direction schemes was investigated. Giles and Desurvire method was used for the mathematical modeling of these configurations where the two level coupled system model equations was solved in MATLAB. In the simulation of the all proposed configurations, an input signal of −35 dBm at the wavelength of 1550 nm and a total of 14 mW pump power at the wavelength of 1480 nm was used for a consistent analysis.

The numerical value of the results obtained is specific to the input parameter values used in the simulations; however, configuration-wise, the EDFA systems found with the best performance are not parameter specific.

The results of this numerical work will help future experimental research of designing and developing ultra-efficient EDFA systems.

Football clubs invest in the implementation of scientific insights that improve the quality of youth academies. In the long run, clubs expect their youth academy investments to result in better trained players. The purpose of this paper is to quantify the impact of the attended youth academies' quality on the future market value of a player.

A dataset containing 94 players trained in 13 different academies has been constructed. The dataset contains characteristics of the players and information on the quality of their attended academies. The impact of the quality of the attended academies on players' future market values was estimated empirically through multiple regression analysis.

The quality of a youth academy has a significant positive impact on a player's market value, which in turn is correlated with higher future wages for players and transfer fees for clubs.

Clubs are advised to pay sufficient attention to investments in their youth academy. This will eventually lead to better trained players and higher revenues. Players in turn should strive to be part of the best academies that provide good training and the opportunity to become a top-earning player. For policymakers, such as football federations, the results imply that stimulating club investments in academies can lead to better national team performances.

The impact of the quality of a youth academy on an individual professional football player's career has never been quantified in the literature before. To this end, a new variable has been constructed using scientific assessments of youth academies.

Solar energy applications are limited because of its intermittent and discontinuous availability with respect to time. Hence, solar energy thermal conversion systems need integration with thermal storage units (TSUs) to use solar energy in off sunshine hours. This paper aims to perform thermal analysis of a solar air heater (SAH) integrated with a phase change material (PCM)-based TSU to supply hot air during night period.

An experimental setup with TSU as main component was prepared with SAH at its upward side, food chamber at its downward side as subcomponents. In TSU, paraffin wax was used as thermal energy storage material. Mass flow rate of air considered as an input parameter in the experiment. Two different absorber plates, namely, plane and ribbed absorber plates were used for the experimentation. Each day for a fixed mass flow of air, observations were made during charging and discharging of PCM.

Nusselt number and convection heat transfer coefficients were analytically calculated by considering flow through TSU as external flow over bank of tubes in a rectangular duct. A temperature drop of around 7-8°C during charging of PCM and temperature rise of around 4-5°C during discharging of PCM was observed from the experimental results. The average practical efficiency of TSU with ribbed absorber plate SAH during charging and discharging of PCM was 22 and 6 per cent, respectively, higher than that of TSU with plane absorber plate SAH.

There are no limitations for research on SAH integrated with TSU. Different PCM including paraffin wax, Glauber’s salt, salt hydrates and water are used for thermal storage. Only limitation is lower efficiency of SAH integrated with TSU because of lower heat transfer coefficients with air as working medium. If it can improve heat transfer coefficients of air then heat transfer rates with these units will be higher.

There are no practical limitations for research on SAH integrated with TSU. Sophisticated instrumentation is needed to measure flow rates, temperatures and pressure variations of air.

In poultry farms during night, chicks cannot survive at cold climatic conditions. Hence, hot air should be supplied to poultry farms whenever the atmospheric temperature drops. It is proposed that, in combination with TSUs, heat produced by SAH is stored in day time in the form of either sensible or latent heat and is retrieved to provide hot air in the night times. This will reduce total operating costs in poultry farms.

Conventionally, people are producing hot air by combusting coal in poultry forms. This cost around Rs. 75,000 per month for a batch of 225 to 250 chicks in a poultry form. Hot air could be produced economically during off sunshine hours from SAH integrated with TSU compared to the conventional method of coal burning. Present experimental investigations conducted to fill the literature gap in this area of research and to design a SAH integrated with TSU to produce hot air for poultry forms.

Wire electric discharge machining (WEDM) is a non-conventional machining process, which is used for cutting parts of civil and military aircraft, rotorcraft, satellites and spacecraft. The cold work steel X153CrMoV12 is used in molds that are needed to produce plastic and metal parts used in these areas. It is only possible to produce parts with precise dimensions and quality with the use of mold steels with sensitive surfaces. The purpose of this study is to analyze X153CrMoV12 material by cutting it with WEDM method in precise dimensions.

The effects of varying cutting parameters on the size of the finished product, surface roughness (SR) and surface hardness were determined by making rough in one pass and precision cuts in different passes. Nikon SMZ745T, Mitutoyo micrometer, Mitutoyo SJ-210 and Insize ISHL-P100 were used for macro-analysis, dimensional control, SR and surface hardness, respectively, to determine the cut qualities.

According to the hardness measurement results obtained from the steel surface before cutting and from the cut surfaces after cutting, there was no significant change in the surface hardness owing to the use of heat-treated steel. Increasing the wire tension as a result of the increase in the number of cutting passes and the decrease in the amount of rough stock left for the final cut increased the cut quality. Cutting precision has increased by preventing vibration of the wire with zero upper and lower water pressure required for slag cleaning.

There are many studies on WEDM in the literature, but there is no similar study emphasizing the importance of the processing parameters such as the number of cutting passes and rough stock amount. In this study, cold work steel with a hardness of 56–60 HRC was machined as rough cut in one pass, rough and fine cut in double pass, double fine cut after one roughing in three passes. As a result of the cuts, 3 µm measurement precision and 0.998 Ra SR were obtained as well as there was no hardness change in the cut surfaces.

Based on a lecture prepared as part of the celebration of Cranfield University's 50th anniversary. After briefly reviewing the early years, including Cranfield University's entry into this technology, discusses the nature of this industry, Some of the technology drivers, including environmental concerns, are examined to provide a background against which the development and the future of the industry can be considered. This is followed by a brief survey of some of the possible new civil aero gas turbine applications over the next 50 years, both the very likely and some curiosities. Finally, the changes that are likely to occur within the industry as a result of wider economic and political trends are considered, as well as the implications for those working within the industry. The development of the civil aero gas turbine has contributed, in large measure, to today's, US$ 300 billion civil aviation industry and is rightly seen as one of mankind's major engineering achievements. A single paper cannot do justice to this industry.

A new type of laser interferometer, developed at the National Physical Laboratory and produced by Linear Instruments, is challenging existing methods for accurate measurement and calibration. Managing director Kenneth Owen talked about it to Jack Hollingum.

This paper aims to study the effect of number of welding passes on microstructure, mechanical and corrosion properties of 409 M ferritic stainless steel. Shielded metal arc welding (SMAW) process is used to weld two metal sheets of 409 M having 3 mm thickness as bead-on-plate with single, double and triple passes. Microstructures were observed at transverse section with the help of optical microscope and with increasing number of passes grain growth, and the width of heat-affected zone (HAZ) increases. The results of tensile tests revealed that as number of passes increases, there is reduction in tensile strength and ductility. Double loop electrochemical potentiokinetic reactivation (DL-EPR) test revealed that as number of passes increases, the degree of sensitization increases. This is due to the deposition of chromium carbides at the grain boundaries and the associated depletion of chromium.

Three welded plates of single, double and triple pass were welded by SMAW process. From three welded plates (single, double and triple passes), samples for microstructural examination were cut in transverse direction (perpendicular to welding direction) with the help of wire-cut electrical discharge machine (EDM). The welded plates were sliced using wire-cut EDM along transverse direction for preparing optical microscopy, tensile testing, microhardness and DL-EPR testing specimens.

From the microstructure, it was observed that the large grain growth, which is dendritic, and the structure become finer to increase in number of welding passes. As number of passes increases, the width of HAZ increases because of the higher temperature at the welded zone. The tensile strength decreases to increase the number of welding passes because of grain coarsening and chromium carbide precipitation in sensitized zone and wider HAZ. The maximum microhardness value was observed for single-pass weld as compared to double- and triple-pass welds because of the fast cooling rate. The degree of sensitization increases to increase the number of passes because of chromium carbide deposition at the grain boundaries.

The authors declare that the manuscript is original and not published elsewhere, and there is no conflict of interest to publish this manuscript.

The build characteristics of two liquid crystal (LC) reactive monomers were studied using a table‐top stereolithography apparatus (TTSLA). LC materials contain stiff, rod‐like mesogenic segments in their molecules, which can be aligned causing an anisotropy in properties. When cured in the aligned state the anisotropic structure is “locked in” resulting in materials with anisotropic physical and mechanical properties. By varying the alignment of layers, properties such as thermal expansion coefficient can be optimized. High heat distortion (or glass transition) temperatures are possible depending on the monomer chemical structure. Working curves for the LC resins were developed under various conditions. A permanent magnet placed outside the TTSLA vat was used to uniformly align the monomer in the nematic state. Photo‐initiator type and content; alignment of the nematic phase; and operating conditions affected the working curve parameters. Glass transition temperatures of post‐cured parts ranged from 75 to 1488C depending on the resin and processing conditions. Mechanical analysis data revealed a factor of two difference between glassy moduli measured in the molecular alignment versus the transverse alignment directions. Based on these initial studies, more advanced resins with higher glass transitions are being developed at the University of Dayton.