Search results

The contact and lubrication performances, which were previously estimated assuming a Gaussian surface, are insufficient due to the non-Gaussian surface characteristics of the honing liner. The purpose of this study is to analyze the liner honing surface and examine its effects on the contact and flow performance.

The fast Fourier transform (FFT) method was used to generate the liner honing texture. Subsequently, an elastoplastic contact model based on boundary element theory was constructed and simulated for the honing surface. The results were compared with those obtained using a Gaussian surface. In addition, flow factors of the honing surfaces were also compared.

The contact pressure and flow factors demonstrate significant disparities when dealing with non-Gaussian surfaces. In the deterministic model, the pressure exhibits considerably diminished magnitudes and a more evenly distribution. Moreover, when the gap between surfaces is narrow, the discrepancy in flow factor across different directions on the real honing surface becomes more prominent compared with the Gaussian surface.

The model incorporates the influence of the non-Gaussian honing surface, thereby enabling more accurate prediction.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0198/

This paper aims to study the impact of transient velocity changes on sealing performance during reciprocating sealing processes.

Establish a model of transient mixed lubrication, solve the transient Reynolds equation, consider the effect of temperature rise at the seal interfaces, and determine the behavior of the seal interfaces, such as film thickness and fluid pressure. Evaluation with friction and leakage rate, calculate the variation of sealing performance with reciprocating velocity under different working conditions, and verify it through bench experiments.

Within a reciprocating stroke, the frictional force decreases with increasing velocity, and the frictional force of the outstroke is greater than that of the instroke; at the time of the stroke transition, the fluid pressure is smallest and the rough peak contact pressure is greatest. At present, the dynamic pressure effect of fluids is the largest, and the friction force also increases, which increases the risk of material wear and failure. Friction and leakage increase with increasing pressure and root mean square roughness. As temperature increases, friction increases and leakage decreases. In studying the performance variations of seal components through a reciprocating sealing experiment, it was found that the friction force decreases with increasing velocity, which is consistent with the calculated results and more similar to the calculated results considering the temperature rise.

This study provides a reference for the study of transient sealing performance.

This paper aims to focus on the high-speed rotary lip seal in aircraft engines, combining its service parameters, its own structure and application conditions, to study the influence of different eccentric forms, eccentricity, rotational speed and other factors on the performance of the rotary lip seal.

A numerical simulation model for high-speed eccentric rotary lip seals has been developed based on the theory of elastic hydrodynamic lubrication. This model comprehensively considers the coupling of multiple physical fields, including interface hydrodynamics, macroscopic solid mechanics and surface microscopic contact mechanics, under the operating conditions of rotary lip seals. The model takes into account eccentricity and uses the hazardous cross-sectional method to quantitatively predict sealing performance parameters, such as leakage rate and friction force.

Eccentricity has a large impact on lip seal performance; lips are more susceptible to wear failure under static eccentricity and to leakage failure under dynamic eccentricity.

This study provides a new idea for the design of rotary lip seal considering eccentricity, which is of guiding significance for the engineering application of rotary lip seal.

This paper aims to investigate the effect of frictional heat on the wear of high-speed rotary lip seals in engines.

In this research paper, the authors focus on the high-speed rotating lip seal of aircraft engines. Using the hybrid lubrication theory, a thermal-fluid-solid coupled numerical simulation model is established to investigate the influence of parameters such as contact pressure distribution, temperature rise and leakage rate on the sealing performance under different operating conditions. By incorporating the Rhee wear theory and combining simulation results with experimental data, a method for predicting the wear of the rotating seal lip profile is proposed. Experimental validation is conducted using a high-speed rotating test rig.

The results indicate that as the speed increases, the rise in frictional heat leads to a decrease in the sealing performance of the lip seal contact region. The experimental results show a similar trend to the numerical simulation results, and considering the effect of frictional heat, the predicted wear of the lip seal profile aligns more closely with the actual wear curve. This highlights the importance of considering the influence of frictional heat in the analysis of rotating seal mechanisms.

This study provides a reference for the prediction of wear profiles of engine high-speed rotary lip seals.

The purpose of this study is to develop a transient wheel–rail rolling contact model to primarily investigate the rail damage under wet condition when the train passes through the welded joints.

The impact force induced by welded joints is obtained through vehicle–track coupling dynamics. The normal and tangential wheel–rail contact pressures were solved by elastohydrodynamic lubrication (EHL) theory and simplified third-body layer theory, respectively. Then, the obtained tangential pressure and normal pressure were applied to the finite element model as moving loads, simulating cyclic loading. Finally, the shakedown map and critical plane method were used to predict rolling contact fatigue (RCF) and the initiation of fatigue cracks.

The results indicate that RCF will occur and fatigue cracks are more prone to appear on the subsurface of the rail, specifically around 2.7 mm below the rail surface in the vicinity of the welded joint and its heat-affected zone.

The cosimulation of numerical model and finite element model was implemented. The influence of surface roughness and fluids was considered. In this model, the normal and tangential wheel–rail contact pressure, the stress and strain and the rail fatigue cracks were obtained under a rail-welded joint excitation.

Due to high speeds, heavy loads, large slide-to-roll ratios (SRR) and other variable operating conditions, some rolling bearings that have been working in harsh conditions may experience flash temperatures in the contact area, which may result in early damage like smearing and then affect service life. This study aims to investigate the flash temperature phenomenon of rolling bearings through theoretical and experimental analysis.

A technology for measuring temperature distribution in rolling ball on disk contact under lubrication was developed. The test-rig can simulate the ball bearing contact. The effects of working conditions such as entrainment speed, load, SRR and lubricating oil viscosity on the flash temperature were investigated.

The results of the theoretical calculation and experiments indicate that the parameters promoting the reduction of film thickness in elastohydrodynamic lubrication are always related with the number of flash points, even film thickness reduced to mixed lubrication. The flash temperature is easier to happen in conditions of high SRR, heavy load, slow entrainment speed and low viscosity oil.

This work conducts an experimental study on the flash temperature phenomenon, providing a test technology for bearing lubrication and failure investigation.

This author has opted into Transparent Peer Review available at: https://publons.com/publon/10.1108/ILT-04-2023-0104

This paper aims to concentrate on recent innovations in flexible wearable sensor technology tailored for monitoring vital signals within the contexts of wearable sensors and systems developed specifically for monitoring health and fitness metrics.

In recent decades, wearable sensors for monitoring vital signals in sports and health have advanced greatly. Vital signals include electrocardiogram, electroencephalogram, electromyography, inertial data, body motions, cardiac rate and bodily fluids like blood and sweating, making them a good choice for sensing devices.

This report reviewed reputable journal articles on wearable sensors for vital signal monitoring, focusing on multimode and integrated multi-dimensional capabilities like structure, accuracy and nature of the devices, which may offer a more versatile and comprehensive solution.

The paper provides essential information on the present obstacles and challenges in this domain and provide a glimpse into the future directions of wearable sensors for the detection of these crucial signals. Importantly, it is evident that the integration of modern fabricating techniques, stretchable electronic devices, the Internet of Things and the application of artificial intelligence algorithms has significantly improved the capacity to efficiently monitor and leverage these signals for human health monitoring, including disease prediction.

As the crucial support component of the propeller power system, the reliability of the operation of submersible pumps is influenced by the lubrication performance of water-lubricated thrust bearings. When the water-lubricated thrust bearings are under start-stop or heavy load conditions, the effect of surface morphology is crucial as the mixed lubrication regime is encountered. This paper aims to develop one mixed lubrication model for the water-lubricated thrust bearings to predict the effects of surface skewness, kurtosis and roughness orientation on the loading carrying capacity and tribological behavior.

This paper developed one improved mixed lubrication model specifically for the water-lubricated thrust bearing system. In this model, the hydrodynamic model was improved by using the height of the rough surface and its probability density function, combined with the average flow model. The asperity contact model was improved by using the equation for the Pearson system of frequency curves to characterize the non-Gaussian aspect of surface roughness distribution.

According to the results, negative skewness, large kurtosis and lateral surface pattern can improve the tribological performance of water-lubricated thrust bearings. Optimizing the surface morphology is a reasonable design method that can improve the performance of water-lubricated thrust bearings.

In this paper, one mixed lubrication model specifically for the water-lubricated thrust bearing with the effect of surface roughness into consideration was developed. Based on the developed model, the effect of surface morphology on tribological behavior can be evaluated.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-08-2023-0247/

This study aims to use a machine learning (ML) model for the prediction of traction coefficient and asperity load ratio for different surface topographies of non-conformal rough contacts.

The input data set for the ML model is generated using a mixed-lubrication model. Surface topography parameters (skewness, kurtosis and pattern ratio), rolling speed and hardness are used as input features in the multi-layer perceptron (MLP) model. The hyperparameter tuning and fivefold cross-validation are also performed to minimize the overfitting.

From the results, it is shown that the MLP model shows excellent accuracy (R² > 90%) on the test data set for making the prediction of mixed lubrication parameters. It is also observed that engineered rough surfaces with high negative skewness, low kurtosis and isotropic surface patterns exhibit a significant low traction coefficient. It is also concluded that the MLP model gives better accuracy in comparison to the random forest regression model based on the training and testing data sets.

Mixed lubrication parameters are predicted by developing a regression-based MLP model. The machine learning model is trained using several topography parameters, which are vital in the mixed-EHL regime because of the lack of regression-fit expressions in previous works. The accuracy of MLP with random forest models is also compared.

The purpose of variable loading conditions (392 N-785N-392N-785N) with break-in period were used to study interactions between zinc dialkyl dithiophosphate (ZDDP) 0.1 P% (phosphorus) and fine-grade molybdenum disulfide (MoS₂) 3%, in different mixtures of NLGI 2 lithium stearate grease. Four-ball wear tests were used to evaluate the tribological properties of different grease mixtures such as coefficient of friction and wear. ASTM 2266 as reported by earlier studies is useful, but it is not representative of real-life applications where variable loads and speeds and different break-in periods play a role and could change the results and the nature of tribofilms.

In this study, chemical and mechanical properties of tribofilms were examined. Moreover, design of experiment was used to examine the data and shorten experimentation time. Research described here is investigating variable loading conditions for real-life applications by using a break-in period of 2 min at the start to minimize asperities and establish a clean surface. Design expert (DOE) analyzes responses to reveal those variables that are single factor and those that are multifactor whether synergistically or antagonistically.

The results indicated that spectrum loading with break-in period showed reduction in wear when tested in greases with ZDDP/MoS₂ combinations. Ramping up or down the load every 7.5 min for a rotational speed of 1,200 rpm and a total of 36,000 revolutions or 30-min time slowed the wear properties of lithium-based grease under different MoS₂ and ZDDP concentrations. Experiments indicated that wear was largely dependent on the loading condition and ZDDP additives during specific break-in period at 1,200 rotational speed. It is believed that MoS₂ greases perform better under spectrum loading and under constant loading when mixed with ZDDP phosphorus.

This research indicates that there is a synergistic interaction between ZDDP, MoS₂ and variable loading especially when a break-in period is applied. The results indicated that wear was largely dependent on the specific speed used with spectrum loading as presented in the energy dispersive spectroscopy and the Auger electron spectroscopy analysis, and thus a 3% MoS₂ grease with ZDDP (phosphorus: 0.1 Wt.%) are needed to improve the wear resistance and improve the friction characteristics.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0016/