Search results

The purpose of this paper is to develop a familiarity analysis of resistive-capacitive (RC) network active circuit operating with unfamiliar low-pass (LP) type negative group delay (NGD) behavior. The design method of NGD circuit is validated by simulation with commercial tool and experimental measurement.

The present research work methodology is structured in three main parts. The familiarity theory of RC-network LP-NGD circuit is developed. The LP-NGD circuit parameters are expressed in function of the targeted time-advance. Then, the feasibility study is based on the theory, simulation and measurement result comparisons.

The RC-network based LP-NGD proof of concept is validated with −1 and −0.5 ms targeted time-advances after design, simulation, test and characterized. The LP-NGD circuit unity gain prototype presents NGD cut-off frequencies of about 269 and 569 Hz for the targeted time-advances, −1 and −0.5 ms, respectively. Bi-exponential and arbitrary waveform signals were tested to verify the targeted time-advance.

The performance of the unfamiliar LP-NGD topology developed in the present study is limited by the parasitic elements of constituting lumped components.

The NGD circuit enables to naturally reduce the undesired delay effect from the electronic and communication systems. The NGD circuit can be exploited to reduce the delay induced by electronic devices and system.

As social impacts of the NGD circuit application, the NGD function is one of prominent solutions to improve the technology performances of future electronic device in term of communication aspect and the transportation system.

The originality of the paper concerns the theoretical approach of the RC-network parameters in function of the targeted time-advance and the input signal bandwidth. In addition, the experimental results are also particularly original.

To address the issues of the insufficient output torque associated with the application of intensifying-flux permanent magnet (PM) machines in electric vehicles, this paper aims to propose an intensifying-flux hybrid excitation PM machine. It is possible to adjust the air gap magnetic field by adjusting the field current in the excitation winding, thereby increasing the torque output capability and speed range of the machine.

First, a novel intensifying-flux hybrid excited permanent magnet synchronous machine (IF-HEPMSM) is proposed on the basis of intensifying-flux permanent magnet synchronous machine (IF-PMSM) and an equivalent magnetic circuit model is established. Second, the tooth width and yoke thickness of the machine stator are optimized to ensure the overload capacity of the machine while effectively improving the wide flux regulation range. Furthermore, the electromagnetic characteristics of the IF-HEPMSM are investigated and compared with the IF-PMSM and conventional permanent magnet synchronous machine (PMSM) by using finite element simulations.

The i_d of IF-HEPMSM and IF-PMSM is greater than zero low-speed magnetizing current. And the flux-weakening current of the IF-HEPMSM is 18% and 3% smaller than of the conventional PMSM and IF-PMSM.

Aiming at the problems of IF-PMSM applied to electric vehicles, this paper proposes an IF-HEPMSM. The air gap magnetic field is adjusted by controlling the current of the excitation winding to improve the reliability of the machine. Therefore, the IF-HEPMSM combines the advantages of high-power density and high efficiency of the PMSM and the controllable magnetic field of the electro-excitation machine, which is of great engineering value when applied in the field of electric vehicles.

The proposed IF-HEPMSM offers better flux regulation capability with electromagnetic characteristics analysis and maps of dq-axis current as compared to IF-PMSM and conventional PMSM. Moreover, the improvement of the torque can make up for the shortcomings of the insufficient torque output capability of the IF-PMSM.

Metro stations have become a crucial aspect of urban rail transportation, integrating facilities, equipment and pedestrians. Impractical physical layout designs and pedestrian psychology impact the effectiveness of an evacuation during a metro fire. Prior research on emergency evacuation has overlooked the complexity of metro stations and failed to adequately consider the physical heterogeneity of stations and pedestrian psychology. Therefore, this study aims to develop a comprehensive evacuation optimization strategy for metro stations by applying the concept of design for safety (DFS) to an emergency evacuation. This approach offers novel insights into the management of complex systems in metro stations during emergencies.

Physical and social factors affecting evacuations are identified. Moreover, the social force model (SFM) is modified by combining the fire dynamics model (FDM) and considering pedestrians' impatience and panic psychology. Based on the Nanjing South Metro Station, a multiagent-based simulation (MABS) model is developed. Finally, based on DFS, optimization strategies for metro stations are suggested.

The most effective evacuation occurs when the width of the stairs is 3 meters and the transfer corridor is 14 meters. Additionally, a luggage disposal area should be set up. The exit strategy of the fewest evacuees is better than the nearest-exit strategy, and the staff in the metro station should guide pedestrians correctly.

Previous studies rarely consider metro stations as sociotechnical systems or apply DFS to proactively reduce evacuation risks. This study provides a new perspective on the evacuation framework of metro stations, which can guide the designers and managers of metro stations.

Ciliated microelectromechanical system (MEMS) vector hydrophones pick up sound signals through Wheatstone bridge in cross beam-ciliated microstructures to achieve information transmission. This paper aims to overcome the complexity and variability of the marine environment and achieve accurate location of targets. In this paper, a new method for ocean noise denoising based on improved complete ensemble empirical mode decomposition with adaptive noise combined with wavelet threshold processing method (CEEMDAN-WT) is proposed.

Based on the CEEMDAN-WT method, the signal is decomposed into different intrinsic mode functions (IMFs), and relevant parameters are selected to obtain IMF denoised signals through WT method for the noisy mode components with low sample entropy. The final pure signal is obtained by reconstructing the unprocessed mode components and the denoising component, effectively separating the signal from the wave interference.

The three methods of empirical mode decomposition (EMD), ensemble empirical mode decomposition (EEMD) and CEEMDAN are compared and analyzed by simulation. The simulation results show that the CEEMDAN method has higher signal-to-noise ratio and smaller reconstruction error than EMD and EEMD. The feasibility and practicability of the combined denoising method are verified by indoor and outdoor experiments, and the underwater acoustic experiment data after processing are combined beams. The problem of blurry left and right sides is solved, and the high precision orientation of the target is realized.

This algorithm provides a theoretical basis for MEMS hydrophones to achieve accurate target positioning in the ocean, and can be applied to the hardware design of sonobuoys, which is widely used in various underwater acoustic work.

This study aims to introduce a predictive homogenization model incorporating electrical percolation considerations to forecast the electrical characteristics of unidirectional carbon-epoxy laminate composites.

This study presents a method for calculating the electrical conductivity tensor for various ply arrangement patterns to elucidate phenomena occurring around the interfaces between plies. These interface models are then integrated into a three-dimensional (3D) magneto-thermal model using the finite element method. A comparative study is conducted between different approaches, emphasizing the advantages of the new model through experimental measurements.

This research facilitates the innovative integration of electrical percolation considerations, resulting in substantial improvement in the prediction of electrical properties of composites. The validity of this improvement is established through comprehensive validation against existing approaches and experimentation.

The study primarily focuses on unidirectional carbon-epoxy laminate composites. Further research is needed to extend the model's applicability to other composite materials and configurations.

The proposed model offers a significant improvement in predicting the electrical properties of composite materials by incorporating electrical percolation considerations at inter-ply interfaces, which have not been addressed in previous studies. This research provides valuable information to improve the accuracy of predictions of the electrical properties of composites and offers a methodology for accounting for these properties in 3D magneto-thermal simulations.

An experimental investigation of hemispherical forebody interaction effects on the drag coefficient of a D-shaped model is carried out for three-dimensional flow in the subcritical range of Reynolds number 1 × 10⁵ ≤ Re ≤ 1.8 × 10⁵. To study the interaction effect, hemispherical shapes of various sizes are attached to the upriver of the D-shaped bluff body model. The diameter of the hemisphere (b₁) varied from 0.25 to 0.75 times the diameter of the D-shaped model (b₂) and its gap from the D-shaped model (g/b₂) ranged from 0.25 to 1.75 b₂.

The experiments were carried out in a low-speed open-circuit closed jet wind tunnel with test section dimensions of 1.2 × 0.9 × 1.8 m (W × H × L) capable of generating maximum velocity up to 45 m/s. The wind tunnel is equipped with a driving unit which has a 175-hp motor with three propellers controlled by a 160-kW inverter drive. Drag force is measured with an internal six-component balance with the help of the Spider 3013 E-pro data acquisition system.

The wind tunnel results show that the hemispherical forebody has a diameter ratio of 0.75 with a gap ratio of 0.25, resulting in a maximum drag reduction of 67%.

The turbulence intensity of the wind tunnel is about 5.6% at a velocity of 18 m/s. The uncertainty in the velocity and the drag coefficient measurement are about ±1.5 and ±2.83 %, respectively. The maximum error in the geometric model is about ±1.33 %.

The results from the research work are helpful in choosing the optimum spacing of road vehicles, especially truck–trailer and launch vehicle applications.

Drag reduction of road vehicle resulting less fuel consumption as well as less pollution to the environment. For instance, tractor trailer experiencing approximately 45% of aerodynamics drag is due to front part of the vehicle. The other contributors are 30% due to trailer base and 25% is due to under body flow. Nearly 65% of energy was spent to overcome the aerodynamic drag, when the vehicle is traveling at the average of 70 kmph (Seifert 2008 and Doyle 2008).

The benefits of placing the forebody in front of the main body will have a strong influence on reducing fuel consumption.

This paper aims to apply the novel numerical model to analyze the effect of pillar material on the response of compound quartz crystal resonator (QCR) with an array of pillars. The performance of the proposed device compared to conventional QCR method was also investigated.

A finite element method model was developed to analyze the behavior of QCR coupled with an array of pillars. The model was composed of an elastic pillar, a solution and a perfectly matched layer. The validation of the model was performed through a comparison between its predictions and previous experimental measurements. Notably, a good agreement was observed between the predicted results and the experimental data.

The effect of pillar Young’s modulus on the coupled QCR and pillars with a diameter of 20 µm, a center-to-center spacing of 40 µm and a density of 2,500 kg/m³ was investigated. The results indicate that multiple vibration modes can be obtained based on Young’s modulus. Notably, in the case of the QCR–pillar in air, the second vibration mode occurred at a critical Young’s modulus of 0.2 MPa, whereas the first mode was observed at 3.75 Mpa. The vibration phase analysis revealed phase-veering behavior at the critical Young’s modulus, which resulted in a sudden jump-and-drop frequency shift. In addition, the results show that the critical Young’s modulus is dependent on the surrounding environment of the pillar. For instance, the critical Young’s modulus for the first mode of the pillar is approximately 3.75 Mpa in air, whereas it increases to 6.5 Mpa in water.

It was concluded that the performance of coupled QCR–pillar devices significantly depends on the pillar material. Therefore, choosing pillar material at critical Young’s modulus can lead to the maximum frequency shift of coupled QCR–pillar devices. The model developed in this work helps the researchers design pillars to achieve maximum frequency shift in their measurements using coupled QCR–pillar.

When solving the cogging torque of complex electromagnetic structures, such as consequent pole hybrid excitation synchronous (CPHES) machine, traditional methods have a huge computational complexity. The notable feature of CPHES machine is the symmetric range of field-strengthening and field-weakening, but this type of machine is destined to be equipped with a complex electromagnetic structure. The purpose of this paper is to propose a hybrid analysis method to quickly and accurately solve the cogging torque of complex 3D electromagnetic structure, which is applicable to CPHES machine with different magnetic pole shapings.

In this paper, a hybrid method for calculating the cogging torque of CPHES machine is proposed, which considers three commonly used pole shapings. Firstly, through magnetic field analysis, the complex 3D finite element analysis (FEA) is simplified to 2D field computing. Secondly, the discretization method is used to obtain the distribution of permeance and permeance differential along the circumference of the air-gap, taking into account the effect of slots. Finally, the cogging torque of the whole motor is obtained by using the idea of modular calculation and the symmetry of the rotor structure.

This method is applicable to different pole shapings. The experimental results show that the proposed method is consistent with 3D FEA and experimental measured results, and the average calculation time is reduced from 8 h to 4 min.

This paper proposes a new concept for calculating cogging torque, which is a hybrid calculation of dimension reduction and discretization modules. Based on magnetic field analysis, the 3D problem is simplified into a 2D issue, reducing computational complexity. Based on the symmetry of the machine structure, a modeling method for discretized analytical models is proposed to calculate the cogging torque of the machine.

Steam explosions are a major safety concern in many modern furnaces. The explosions are sometimes caused by water ingress into the furnace from leaks in its high-pressure (HP) cooling water system, coming into contact with molten matte. To address such safety issues related to steam explosions, risk based inspection (RBI) is suggested in this paper. RBI is presently one of the best-practice methodologies to provide an inspection schedule and ensure the mechanical integrity of pressure vessels. The application of RBIs on furnace HP cooling systems in this work is performed by incorporating the proportional hazards model (PHM) with the RBI approach; the PHM uses real-time condition data to allow dynamic decision-making on inspection and maintenance planning.

To accomplish this, a case study is presented that applies an HP cooling system data with moisture and cumulated feed rate as covariates or condition indicators to compute the probability of failure and the consequence of failure (CoF), which is modelled based on the boiling liquid-expanding vapour explosion (BLEVE) theory.

The benefit of this approach is that the risk assessment introduces real-time condition data in addition to time-based failure information to allow improved dynamic decision-making for inspection and maintenance planning of the HP cooling system. The work presented here comprises the application of the newly proposed methodology in the context of pressure vessels, considering the important challenge of possible explosion accidents due to BLEVE as the CoF calculations.

This paper however aims to optimise the inspection schedule on the HP cooling system, by incorporating PHM into the RBI methodology, as was recently proposed in the literature by Lelo et al. (2022). Moisture and cumulated feed rate are used as covariate. At the end, risk mitigation policy is suggested.

In this paper, the proposed methodology yields a dynamically calculated quantified risk, which emphasised the imperative for mitigating the risk, as well as presents a number of mitigation options, to quantifiably affect such mitigation.

The purpose of this paper is to introduce and analyze a dual-side-permanent-magnet Halbach array vernier (DSPMHV) machine and to propose methods for achieving high torque density.

Flux harmonics and torque characteristics are analyzed by using finite element analysis. First, a suitable pole-slot combination is selected by comparison. Second, field modulation processes of DSPMHV machine are analyzed to identify the reason for high torque density. And it is compared with dual-side-PM (DSPM) machine to analyze flux harmonic and verify the flux concentrating effect of the Halbach array.

The permanent magnet (PM) field of the DSPM machine is approximately equal to the superposition of stator-PM field and rotor-PM field, which is the reason for high torque density. And the Halbach array can reduce flux leakage and increase the amplitude of main flux harmonics, then further improves torque. Improvement of torque can be achieved by choosing right pole-slot combination, adopting DSPM machine structure, reducing flux leakage and adopting field modulation principle.

The DSPMHV machine with split-tooth is proposed in this paper by combining the Halbach array with DSPM structure. This paper analyzes the bidirectional field modulation process, the reason for high torque density of the DSPM machine is obtained. Comparison with the DSPM machine verifies the flux concentrating effect of Halbach array. To alleviate the magnetic saturation in part of stator teeth, this paper proposes an improved DSPMHV machine with shaped auxiliary magnet.