Search results

In the field of research on the application of digital printing to textile materials, there are still many research issues that arise from the very demanding interaction of digital printing technology and the complex, heterogeneous surface system of textile materials. This is precisely why the area of pre-treatment of textile materials is in need of research, and the purpose of this research was to establish the level of influence of physical and chemical activation of the textile surface with plasma and the possibility of improving the quality of the print and colour reproduction.

The paper deals with the possibility of applying argon and oxygen cold low-pressure plasma in the processing of cellulose knitted fabrics, with the aim of improving the quality of the print and colour reproduction in digital pigment inkjet printing. The selected raw material samples were 100% raw cotton and lyocell. After plasma treatment, the samples were printed by digital ink jet printing with water-based pigment printing ink. An analysis of the micromorphological structure of untreated and plasma-treated samples before and after printing was carried out, and a comparative analysis of the colour of the printed elements was carried out depending on the pre-treatment.

The conducted research showed a positive influence of plasma pre-treatment on the coverage of the fibre surface with pigments, the uniformity of pigment distribution along the fibre surface and the uniformity of the distribution of the polymeric binder layer. This has a positive effect on colour reproduction. Also, certain improvements in colourfastness to washing were obtained.

Considering the complexity of the topic, although exhaustive, this research is not sufficient in itself, but opens up new questions and gives ideas for further research that must be carried out in this area.

Also, this kind of research contributes to the possibility of adopting the idea of industrial plasma transformation, as an ecologically sustainable functionalisation of textiles, which has not yet been established.

This research is certainly a contribution to the establishment of acceptable textile pre-treatment methods in the field of digital printing, as one of the key quality factors in digital textile printing (DTP). Considering the still large number of obstacles and unanswered questions encountered in the field of digital printing on textiles, this kind of research is a strong contribution to the understanding of the fundamental mechanisms of the complex interaction between printing ink and textile.

Utilizing electrical discharge machining (EDM) to process micro-holes in superalloys may lead to the formation of remelting layers and micro-cracks on the machined surface. This work proposes a method of composite processing of EDM and ultrasonic vibration drilling for machining precision micro-holes in complex positions of superalloys.

A six-axis computer numerical control (CNC) machine tool was developed, whose software control system adopted a real-time control architecture that integrates electrical discharge and ultrasonic vibration drilling. Among them, the CNC system software was developed based on Windows + RTX architecture, which could process the real-time processing state received by the hardware terminal and adjust the processing state. Based on the SoC (System on Chip) technology, an architecture for a pulse generator was developed. The circuit of the pulse generator was designed and implemented. Additionally, a composite mechanical system was engineered for both drilling and EDM. Two sets of control boards were designed for the hardware terminal. One set was the EDM discharge control board, which detected the discharge state and provided the pulse waveform for turning on the transistor. The other was a relay control card based on STM32, which could meet the switch between EDM and ultrasonic vibration, and used the Modbus protocol to communicate with the machining control software.

The mechanical structure of the designed composite machine tool can effectively avoid interference between the EDM spindle and the drilling spindle. The removal rate of the remelting layer on 1.5 mm single crystal superalloys after composite processing can reach over 90%. The average processing time per millimeter was 55 s, and the measured inner surface roughness of the hole was less than 1.6 µm, which realized the  micro-hole machining without remelting layer, heat affected zone and micro-cracks in the single crystal superalloy.

The test results proved that the key techniques developed in this paper were suite for micro-hole machining of special materials.

Menstruation is a part of the female reproductive cycle that begins with adolescence. Menstruation is a natural change; it relates to several malpractices and misconceptions that may contribute to adverse health outcomes.

The authors have searched relevant papers using Google Scholar and PubMed to write this mini review.

During menstruation, poor hygiene maintenance can cause serious illness, which includes the urinary tract and reproductive tract infection. Menstruation management is a hygienic system, and it is essential for females because poor hygiene maintenance during menstruation can cause some infections and numerous sexually transmitted diseases. There are a few nanotechnology-based products that have come into the market to offer some relief to females during their periods.

This mini review will help researchers to design innovative female hygiene products that can relieve the discomfort caused to women during their reproductive age.

The purpose of this paper is to investigate and review the impact of the use of statistical quality control (SQC) development and analytical and numerical methods on average run length for econometric applications.

This study used several academic databases to survey and analyze the literature on SQC tools, their characteristics and applications. The surveys covered both parametric and nonparametric SQC.

This survey paper reviews the literature both control charts and methodology to evaluate an average run length (ARL) which the SQC charts can be applied to any data. Because of the nonparametric control chart is an alternative effective to standard control charts. The mixed nonparametric control chart can overcome the assumption of normality and independence. In addition, there are several analytical and numerical methods for determining the ARL, those of methods; Markov Chain, Martingales, Numerical Integral Equation and Explicit formulas which use less time consuming but accuracy. New ideas of mixed parametric and nonparametric control charts are effective alternatives for econometric applications.

In terms of mixed nonparametric control charts, this can be applied to all data which no limitation in using of the proposed control chart. In particular, the data consist of volatility and fluctuation usually occurred in econometric solutions. Furthermore, to find the ARL as a performance measure, an explicit formula for the ARL of time series data can be derived using the integral equation and its accuracy can be verified using the numerical integral equation.