Search results

The purpose of this paper is to determine the effect of clothing fabrics, sizes and air ventilation rate on the volume and thickness of the air gap under the air ventilation garments (AVGs).

The geometric models of the human body and clothing were obtained by using a 3D body scanner. Then the distribution of the volume and thickness of the air gap for four clothing fabrics and three air ventilation rates (0L/S, 12L/S and 20L/S) were calculated by Geomagic software. Finally, a more suitable fabric was selected from the analysis to compare the distribution of the air gap entrapped for four clothing sizes (S, M, L and XL) and the three air ventilation rates.

The results show that the influence of air ventilation rate on the air gap volume and thickness is more obvious than that of the clothing fabrics and sizes. The higher is the air ventilation rate, the thicker is the air gap entrapped, and more evenly distributed is the air gap. It can be seen that the thickness of the air gap in the chest does not change significantly with the changes of the air ventilation rates, clothing fabrics and sizes, while the air gap in the waist is affected significantly.

This research provides a better understanding of the distribution of the air gap entrapped in ventilated garments, which can help in designing the optimal air gap dimensions and thus provide a basis and a reference for the design of the AVGs.

Determining the suitable material and accurate thickness of the thermal insulation layer used in exterior walls during the design phase of a building can be challenging. This study aims to determine suitable material and optimum thickness for the insulation layer considering both operational and embodied factors by a comprehensive assessment of the energy, economic and environmental (3E) parameters.

First, the energy model of an existing building was created by using Autodesk Revit software according to the as-built floor layout to evaluate the impact of five alternative insulating materials in varying thickness values. Second, using the results derived from the model, a thorough evaluation was conducted to ascertain the optimal insulation material and thickness through individual analysis of 3E factors, followed by a comprehensive analysis considering the three aforementioned factors simultaneously.

The findings indicated that polyurethane with 13 cm thickness, rockwool with 10 cm thickness and EPS with 20 cm thickness were the best states based on energy consumption, cost and environmental footprint, respectively. After completing the 3E investigation, the 15-cm-thick mineral wool insulation was presented as the ideal state.

This study explores how suitable material and thickness of insulating material can be determined in advance during the design phase of a building, which is a lot more accurate and cost-effective than applying insulating materials by assumed thickness in the construction phase.

To the best of the authors’ knowledge, this paper is unique in investigating the advantages of using thermally insulating materials in the context of a mosque structure, taking into account its distinctive attributes that deviate from those of typical buildings. Furthermore, there has been no prior analysis of the cost and sustainability implications of these materials concerning the characteristics of subtropical monsoon climate.

In this study a numerical analysis of the elastohydrodynamic lubrication point contact problem in the unsteady state of reciprocating motion is presented. The effects of frequency, stroke length and load on film thickness and pressure variation during one operating cycle are discussed. The general tribological behavior of elastohydrodynamic lubrication during reciprocating motion is explained.

The system of equations of Reynolds, film thickness considering surface deformation and load balance equations are solved using the Newton-Raphson technique with the Gauss-Seidel iteration method. Numerical solutions were performed with a sinusoidal contact surface velocity to simulate reciprocating elastohydrodynamics. The methodology is validated using historical experimental measurements/observations and numerical predictions from other researchers.

The numerical results showed that the change in oil film during a stroke is controlled by both wedge and squeeze effects. When the surface velocity is zero at the stroke end, the squeeze effect is most noticeable. As the frequency increases, the general trend of central and minimum film thickness increases. With the same entraining speed but different stroke lengths, the properties of the oil film differ from one another, with an increase in stroke length leading to a reduction in film thickness. Finally, the numerical results showed that the overall film thickness decreases with increasing load.

General tribological behaviors of elastohydrodynamic lubricating point contact, represented by pressure and film thickness variations over time and profiles, are analyzed under reciprocating motion during one working cycle to show the effects of frequency, stroke length and applied load.

Inspired by the high-friction performance of the soft toe pads of tree frogs, this study aims to investigate the effect of elastic deformation on the lubrication properties of squeezing films inside soft tribocontacts with microstructured surface under wet conditions.

A one-dimensional hydrodynamic extrusion model was used to study the film lubrication characteristics of conformal contact. The lubrication characteristics of the extruded film, including load-carrying capacity, liquid flow and surface elastic deformation, were obtained through the simultaneously iterative solution of the fluid-governing and deformation equations.

The results show that the hydrodynamic pressure is approximating parabolically and symmetrically distributed in the contact area, and the peak value appears in the center of the extrusion surface. Elastic deformation increases the thickness of the liquid film, weakens the bearing capacity and homogenizes the liquid flow rate of inside soft friction contact. The magnitude of this effect greatly increases as the initial liquid film thickness decreases. Moreover, the elastic deformation directly affects the average film thickness of the extrusion contact. Narrow and shallow microchannels are found to result in a more prominent elastic deformation on the microstructured soft surface.

These results present a design for soft tribocontacts suitable for submerged or wet environments involving high friction, such as wiper blades, in situ flexible electrons and underwater robots.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-02-2024-0049/

This study aims to understand how the facesheet size, orientation and core size influence the analytical failure mechanism mode of glass fibre reinforced polymer (GFRP)/polyvinyl chloride (PVC) sandwich structures subjected to three-point bending. The purpose of this study was to develop failure-mode map of GFRP/PVC sandwich structures. Sandwich structures with different facesheet and core thicknesses were used to develop the failure map.

The sandwich structure and facesheet were fabricated using a vacuum-assisted resin infusion method with core sizes of 10, 15 and 20 mm and facesheet thicknesses of 1.5 and 3 mm and were arranged in three different orientations: angle-ply, cross-ply and quasi-isotropic. The key failure modes that occur in sandwich structures were used to predict possible failures in the developed material. Analytical equations were used in MATLAB for each observed failure mode. The probable failure modes, namely, face yielding, core shear and indentation equations, were used to construct the failure maps and were compared with the experimental data.

The boundary of the two failure modes shifts with changes in the facesheet and core thicknesses. The theoretical stiffness of sandwich panels was higher than the experimental stiffness. Based on strength-to-weight ratio, specimens E10-4, A15-8 and E20-8 exhibited the best optimum values owing to their shorter distance to the boundary lines.

In this study, a failure map was used to predict the possible failure modes for different GFRP facesheet orientations and thicknesses and PVC core thickness sandwich structures. Little is known about the prediction of the failure modes of unidirectional GFRP arranged in different orientations and thicknesses and PVC core thicknesses for sandwich structures. Few studies have used failure mode maps with unidirectional GFRP oriented in angle-ply, cross-ply and quasi-isotropic directions as a facesheet for sandwich structures compared to bidirectional mats. This study can serve as a guide for the correct selection of materials during the design process of sandwich structures.

Despite the reputation of the metal-based porous media for their ability to augment heat transfer as widely witnessed in the literature and practically operating heat exchanging applications, the coexisting penalty of the increased pressure drop demanding increased pumping power poses a major concern that invites the need for an alternate solution to handle this unsought outcome. Therefore, this study aims at providing a better solution to the existing cost and benefit scenarios to benefit a plethora of engineering applications including energy transfer, energy storage and energy conversion.

This work highlights on the property of stacked woven wire mesh porous media such as their stacking types, porous conditions and thickness scenarios that can potentially result in distinct trade-off scenarios. A vertical channel is numerical modelled by using REV scaled modelling technique using Darcy-Forchheimer and local thermal non-equilibrium models to illustrate the possibilities of this variety of trade off scenarios between the desirable heat transfer and the unsought flow resistance.

This work illustrates the advantages of wire mesh-based porous medium and its distinct potential in controlling the existing trade-offs between the cost and benefit aspects. It is found that by varying the features of wire mesh porous media, the interplay between the conflictingly existing characteristics can be much easily handled specific to distinct requirements associated with variety of engineering applications.

The study emphasizes on a new solution or methodology to handle the penalty of pressure drop associated with metal-based porous media. Through this study, a novel approach to control the ultimately costing pumping power at the benefit of increased heat transfer is provided considering various requirements that could be associated with any thermal management systems. Various possibilities and potentials of wire mesh porous media are illustrated highlighting on their benefit of ease with which the mentioned goals can be achieved.

The impact of the application of hollow structures through variations of infill patterns and their density on the tensile properties was considered. The mechanical properties of the parts have a significant influence on the behavior and reliability of the parts in exploitation.

In this paper, the mechanical properties of the additively manufactured ABS material were investigated depending on the FDM printing parameters, which relate both to process parameters such as printing velocity and layer thickness, but also to coupled influence with the change of specimen orientation, that is raster angle. A standard tensile test was applied so that the specimens were prepared according to the ASTM D638 standard.

The results of the conducted experimental research enable the identification of the optimal choice of printing parameters for additively produced ABS materials with the highest values of strain at break and tensile strength. The significance of the obtained results is reflected in the recommendations for the selection of appropriate combination of process parameters for additive manufacturing of ABS parts using FDM technology.

This paper evaluates influence of FDM printing parameters on the tensile strength of parts and therefore on the reliability of the parts.

This paper aims to investigate the moisture diffusion behavior in a system-in-package module systematically by moisture-thermalmechanical-coupled finite element modeling with different structure parameters under increasingly harsh environment.

A finite element model for a system-in-package module was built with moisture-thermal-mechanical-coupled effects to study the subsequences of hygrothermal conditions.

It was found in this paper that the moisture diffusion path was mainly dominated by hygrothermal conditions, though structure parameters can affect the moisture distribution. At lower temperatures (30°C~85°C), the direction of moisture diffusion was from the periphery to the center of the module, which was commonly found in simulations and literatures. However, at relatively higher temperatures (125°C~220°C), the diffusion was from printed circuit board (PCB) to EMC due to the concentration gradient from PCB to EMC across the EMC/PCB interface. It was also found that there exists a critical thickness for EMC and PCB during the moisture diffusion. When the thickness of EMC or PCB increased to a certain value, the diffusion of moisture reached a stable state, and the concentration on the die surface in the packaging module hardly changed. A quantified correlation between the moisture diffusion coefficient and the critical thickness was then proposed for structure parameter optimization in the design of system-in-package module.

The different moisture diffusion behaviors at low and high temperatures have seldom been reported before. This work can facilitate the understanding of moisture diffusion within a package and offer some methods about minimizing its effect by design optimization.

The rapid growth of 3D printing has transformed the cost-effective production of prototypes and functional items, primarily using extrusion technology with thermoplastics. This study aims to focus on optimizing mechanical properties, precisely highlighting the crucial role of mechanical compressive strength in ensuring the functionality and durability of 3D-printed components, especially in industrial and engineering applications.

Using the Box−Behnken experimental design, the research investigated the influence of layer thickness, wall perimeter and infill level on mechanical resistance through compression. Parameters such as maximum force, printing time and mass utilization are considered for assessing and enhancing mechanical properties.

The layer thickness was identified as the most influential parameter over the compression time, followed by the degree of infill. The number of surface layers significantly influences both maximum strength and total mass. Optimization strategies suggest reducing infill percentage while maintaining moderate to high values for surface layers and layer thickness, enabling the production of lightweight components with adequate mechanical strength and reduced printing time. Experimental validation confirms the effectiveness of these strategies, with generated regression equations serving as a valuable predictive tool for similar parameters.

This research offers valuable insights for industries using 3D printing in creating prototypes and functional parts. By identifying optimal parameters such as layer thickness, surface layers and infill levels, the study helps manufacturers achieve stronger, lighter and more cost-efficient components. For industrial and engineering applications, adopting the outlined optimization strategies can result in components with enhanced mechanical strength and durability, while also reducing material costs and printing times. Practitioners can use the developed regression equations as predictive tools to fine-tune their production processes and achieve desired mechanical properties more effectively.

This research contributes to the ongoing evolution of additive manufacturing, providing insights into optimizing structural rigidity through polylactic acid (PLA) selection, Box−Behnken design and overall process optimization. These findings advance the understanding of fused deposition modeling (FDM) technology and offer practical implications for more efficient and economical 3D printing processes in industrial and engineering applications.

This study aims to investigate the influence mechanism of thermal-mechanical deformations on the CO₂ mixture gases dry gas seal (DGS) flow field and compare the deformation characteristics and sealing performance between two-way and one-way thermal-fluid-solid coupling models.

The authors established a two-way thermal-fluid-solid coupling model by using gas film thickness as the transfer parameter between the fluid and solid domain, and the model was solved using the finite difference method and finite element method. The thermal-mechanical deformations of the sealing rings, the influence of face deformation on the flow field and sealing performance were obtained.

Thermal-mechanical deformations cause a convergent gap between the two sealing end faces, resulting in an increase in the gas film thickness, but a decrease in the gas film temperature and sealing ring temperature. The axial relative deformations of rotating and stationary ring end faces caused by mechanical and thermal loads in the two-way coupling model are less than those in the one-way coupling (OWC) model, and the gas film thickness and leakage rate are larger than those in the OWC model, whereas the gas film stiffness is the opposite.

This paper provides a theoretical support and reference for the operational stability and structural optimization design of CO₂ mixture gases DGS under high-pressure and high-speed operation conditions.