Search results

This paper focusses on the aftermath of disruptions and the importance of the two largest canals (Suez and Panama), commenting on how during the pandemic the canal fees were lowered. Considering the ongoing efforts to decarbonize shipping, some of the ongoing disruptions will help reach these objectives faster.

Following a literature review of route choice in shipping, and a presentation of significant disruptions in recent years, the author deploys a simplified fuel consumption model and conduct case study analyses to compare different routes environmentally and economically.

The results explain why at times of low fuel prices as in 2020, canals provided discounts to entice ship operators to keep transiting these, instead of opting for longer routes. Considering the ongoing repercussions of the pandemic in supply chains, as well as the potential introduction of market-based measures in shipping, the value of transiting canals will be much higher in the coming years.

The main limitation in this work is that the author used the publicly available information on canal tolls, for the different ship types examined.

The envisioned model is simple, and it can be readily used for any ship and route (port to port) combination available, if ship data are available to researchers.

It is possible that canal tolls will increase, to account for the additional environmental benefits brought to ship operators.

The methodology is simple and transferable, and the author proposes several interesting research questions for follow-up work.

Gas insulated systems, such as gas insulated lines (GIL), use insulating gas, mostly sulfur hexalfluoride (SF₆), to enable a higher dielectric strength compared to e.g. air. However, under high voltage direct current conditions, charge accumulation and electric field stress may occur, which may lead to partial discharge or system failure. Therefore, numerical simulations are used to design the system and determine the electric field and charge distribution. Although the gas conduction shows a more complex current–voltage characteristic compared to solid insulation, the electric conductivity of the SF₆ gas is set as constant in most works. The purpose of this study is to investigate different approaches to address the conduction in the gas properly for numerical simulations.

In this work, two approaches are investigated to address the conduction in the insulating gas and are compared to each other. One method is an ion-drift-diffusion model, where the conduction in the gas is described by the ion motion in the SF₆ gas. However, this method is computationally expensive. Alternatively, a less complex approach is an electro-thermal model with the application of an electric conductivity model for the SF₆ gas. Measurements show that the electric conductivity in the SF₆ gas has a nonlinear dependency on temperature, electric field and gas pressure. From these measurements, an electric conductivity model was developed. Both methods are compared by simulation results, where different parameters and conditions are considered, to investigate the potential of the electric conductivity model as a computationally less expensive alternative.

The simulation results of both simulation approaches show similar results, proving the electric conductivity for the SF₆ gas as a valid alternative. Using the electro-thermal model approach with the application of the electric conductivity model enables a solution time up to six times faster compared to the ion-drift-diffusion model. The application of the model allows to examine the influence of different parameters such as temperature and gas pressure on the electric field distribution in the GIL, whereas the ion-drift-diffusion model enables to investigate the distribution of homo- and heteropolar charges in the insulation gas.

This work presents numerical simulation models for high voltage direct current GIL, where the conduction in the SF₆ gas is described more precisely compared to a definition of a constant electric conductivity value for the insulation gas. The electric conductivity model for the SF₆ gas allows for consideration of the current–voltage characteristics of the gas, is computationally less expensive compared to an ion-drift diffusion model and needs considerably less solution time.

This study aimed to characterize the concentrations of indoor pollutants (such as carbon dioxide (CO₂), ozone (O₃), nitrogen dioxide (NO₂) and sulfur dioxide (SO₂), as well as particulate matter (PM) (PM₁, PM_2.5 and PM₁₀) in Akure, Nigeria, as well as the relationship between the parameters’ concentrations.

The evaluation, which lasted four months, used a low-cost air sensor that was positioned two meters above the ground. All sensor procedures were correctly carried out.

CO₂ (430.34 ppm), NO₂ (93.31 ppb), O₃ (19.94 ppb), SO₂ (40.87 ppb), PM₁ (29.31 µg/m3), PM_2.5 (43.56 µg/m³), PM₁₀ (50.70 µg/m³), temperature (32.4°C) and relative humidity (50.53%) were the average values obtained. The Pearson correlation depicted the relationships between the pollutants and weather factors. With the exception of April, which had significant SO₂ (18%) and low PM₁₀ (49%) contributions, NO₂ and PM₁₀ were the most common pollutants in all of the months. The mean air quality index (AQI) for NO₂ indicated that the AQI was “moderate” (51–100). In contrast to SO₂, whose AQI ranged from “moderate” to “very unhealthy,” O₃'s AQI ranged from “good” (50) to “unhealthy” (151–200). Since PM₁, PM_2.5 and PM₁₀ made up the majority of PC1’s contribution, both PM_2.5 and PM₁₀ were deemed “hazardous.”

The practical implication of indoor air pollution is long-term health effects, including heart disease, lung cancer and respiratory diseases such as emphysema. Indoor air pollution can also cause long-term damage to people’s nerves, brain, kidneys, liver and other organs.

Lack of literature in terms of indoor air quality (IAQ) in Akure, Ondo State. With this work, the information obtained will assist all stakeholders in policy formulation and implementation. Again, the low-cost sensor used is new to this part of the world.

The purpose of this study is to investigate the accumulation process of transfer film formation and dissipation and its effect on friction coefficients in non asbestos organic friction materials with various lubricant FeS₂ contents.

In total, 2.5%, 5% and 10% FeS₂ were added as lubricating components to the friction materials. Friction tests composed of two stages were conducted for these friction materials, and the friction surfaces of the counterpart discs were examined using scanning electron microscopy.

The transfer film formation reduced the friction coefficients, and the transfer film dissipation influenced the recovery of the friction coefficients. The effect of a high content of FeS₂ was to promote the transfer film formation at high temperatures and to hinder the transfer film dissipation at low temperatures, thus resulting in a decrease in the friction coefficients at high temperatures together with recovery retardation at low temperatures.

FeS₂ contributed to the transfer film formation at high temperatures in the fade test but hindered the transfer film removal in the recovery test, resulting in the retardation of friction coefficient recovery. The mechanism by which the FeS₂ lubricant component affected the transfer film formation and dissipation was analyzed and attributed to the different levels of FeS₂ pyrolysis at different temperature levels.

In pursuit of affordable and nutrient-rich food alternatives, the symbiotic culture of bacteria and yeast (SCOBY) emerged as a selected food ink for 3D printing. The purpose of this paper is to harness SCOBY’s potential to create cost-effective and nourishing food options using the innovative technique of 3D printing.

This work presents a comparative analysis of the printability of SCOBY with blends of wheat flour, with a focus on the optimization of process variables such as printing composition, nozzle height, nozzle diameter, printing speed, extrusion motor speed and extrusion rate. Extensive research was carried out to explore the diverse physical, mechanical and rheological properties of food ink.

Among the ratios tested, SCOBY, with SCOBY:wheat flour ratio at 1:0.33 exhibited the highest precision and layer definition when 3D printed at 50 and 60 mm/s printing speeds, 180 rpm motor speed and 0.8 mm nozzle with a 0.005 cm³/s extrusion rate, with minimum alteration in colour.

Food layered manufacturing (FLM) is a novel concept that uses a specialized printer to fabricate edible objects by layering edible materials, such as chocolate, confectionaries and pureed fruits and vegetables. FLM is a disruptive technology that enables the creation of personalized and texture-tailored foods, incorporating desired nutritional values and food quality, using a variety of ingredients and additions. This research highlights the potential of SCOBY as a viable material for 3D food printing applications.

This study aims to comparatively reveal the physical, thermal and mechanical properties of horse tail and mane hairs, which have the potential to be used in many areas.

Physical properties of horsehairs such as diameter, density, moisture and water absorption were measured. Fourier transform infrared, field emission scanning electron microscopy and amino acid analyzes were applied to the hairs. Thermal stability of horsehair was investigated by thermogravimetric analysis and differential scanning calorimetry analysis. In addition, breaking strength and elongation values of mane and tail hairs were measured.

As a result of morphological analysis of horsehair, it was observed that there are usually gaps in the internal structure of horsehair, but the size and continuity of these gaps vary. It has been determined that there is a significant difference between the tenacity values of tail and mane hairs as well as geometric characteristics. In addition, amino acid analysis has shown that the amino acid contents of horse tail and mane hairs are similar and not much different from sheep’s wool.

Horsehair has been used for various purposes such as clothing, accessories, brushes, upholstery and reinforcement material. To use horsehair in accordance with its application area and performance characteristics, it is necessary to know its physical, thermal and mechanical properties. It is considerable to reveal the similar and different aspects of tail and mane hairs to determine whether they are alternatives to each other. Therefore, revealing the characteristics of tail and mane hairs comparatively constitutes the originality of this study.

This study aims to identify the bioactive compounds in the Onion (Allium burdickii [A.B]) bulb using Raman and Fourier transform infrared spectroscopy (FTIR) spectroscopy. It assessed the extraction conditions of bioactive compounds from A.B. while evaluating the best extraction conditions.

The research opted for an experimental qualitative approach. It examined the extraction conditions of A.B., namely, temperature (°C), time (min) and mass-to-liquor ratio (M:R) using ultraviolet-visible spectrophotometry. Identification of bioactive compounds present in the dye was performed using Raman spectroscopy and the validation of the results was done by FTIR spectroscopy.

The study determined the best extraction conditions (time, temperature, M:R) for A.B bulb. The study confirmed the presence of bioactive compounds.

The limitation was quantification of bioactive compounds in A.B bulb.

The findings prove that the A.B. bulb can provide a sustainable source of bioactive compounds (functionalized compounds). The study provides suitable extraction conditions for A.B. and further elaborates on the techniques for identifying bioactive compounds in A.B. bulb extracts.

The study provides A.B. as a source of bioactive compounds and a clean dye for textile coloration.

To the best of the authors’ knowledge, there is no documented study on the qualitative analysis of bioactive compounds in A.B using Raman and FTIR. Therefore, the study fulfils the identified need to ascertain alternative procedures for the analysis of bioactive compounds.

This study explores a hegemonic alliance and the role of relational forms of accounting and accountablity in the making of contemporary capitalism.

We use the WikiLeaks “Cablegate” documents to provide an account of the detailed machinations between interest groups (corporations and the state) that are constitutive of hegemonic activity.

Our analysis of the “Cablegate” documents shows that the US and Chevron were crafting a central role for Turkmenistan and its president on the global political stage as early as 2007, despite offical reporting beginning only in 2009. The documents exemplify how “accountability gaps” occlude the understanding of interdependence between capital and the state.

The study contributes to a growing idea that official accounts offer a fictionalized narrative of corporations as existing independently, and thus expands the boundaries associated with studying multinational corporate activities to include their interdependencies with the modern state.

The study traces how global capitalism extends into new territories through diplomatic channels, as a strategic initiative between powerful state and capital interests, arguing that the outcome is the empowerment of authoritarian states at the cost of democracy.

The study argues that previous accounting and accountability research has overlooked the larger picture of how capital and the state work together to secure a mutual hegemonic interest. We advocate for a more complete account of these activities that circumvents official, often restricted, views of global capitalism.

The purpose of variable loading conditions (392 N-785N-392N-785N) with break-in period were used to study interactions between zinc dialkyl dithiophosphate (ZDDP) 0.1 P% (phosphorus) and fine-grade molybdenum disulfide (MoS₂) 3%, in different mixtures of NLGI 2 lithium stearate grease. Four-ball wear tests were used to evaluate the tribological properties of different grease mixtures such as coefficient of friction and wear. ASTM 2266 as reported by earlier studies is useful, but it is not representative of real-life applications where variable loads and speeds and different break-in periods play a role and could change the results and the nature of tribofilms.

In this study, chemical and mechanical properties of tribofilms were examined. Moreover, design of experiment was used to examine the data and shorten experimentation time. Research described here is investigating variable loading conditions for real-life applications by using a break-in period of 2 min at the start to minimize asperities and establish a clean surface. Design expert (DOE) analyzes responses to reveal those variables that are single factor and those that are multifactor whether synergistically or antagonistically.

The results indicated that spectrum loading with break-in period showed reduction in wear when tested in greases with ZDDP/MoS₂ combinations. Ramping up or down the load every 7.5 min for a rotational speed of 1,200 rpm and a total of 36,000 revolutions or 30-min time slowed the wear properties of lithium-based grease under different MoS₂ and ZDDP concentrations. Experiments indicated that wear was largely dependent on the loading condition and ZDDP additives during specific break-in period at 1,200 rotational speed. It is believed that MoS₂ greases perform better under spectrum loading and under constant loading when mixed with ZDDP phosphorus.

This research indicates that there is a synergistic interaction between ZDDP, MoS₂ and variable loading especially when a break-in period is applied. The results indicated that wear was largely dependent on the specific speed used with spectrum loading as presented in the energy dispersive spectroscopy and the Auger electron spectroscopy analysis, and thus a 3% MoS₂ grease with ZDDP (phosphorus: 0.1 Wt.%) are needed to improve the wear resistance and improve the friction characteristics.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-01-2024-0016/

Disruptions at ports may destroy the planned ship schedules profoundly, which is an imperative operation problem that shipping companies need to overcome. This paper attempts to help shipping companies cope with port disruptions through recovery scheduling.

This paper studies the ship coping strategies for the port disruptions caused by severe weather. A novel mixed-integer nonlinear programming model is proposed to solve the ship schedule recovery problem (SSRP). A distributionally robust mean conditional value-at-risk (CVaR) optimization model was constructed to handle the SSRP with port disruption uncertainties, for which we derive tractable counterparts under the polyhedral ambiguity sets.

The results show that the size of ambiguity set, confidence level and risk-aversion parameter can significantly affect the optimal values, decision-makers should choose a reasonable parameter combination. Besides, sailing speed adjustment and handling rate adjustment are effective strategies in SSRP but may not be sufficient to recover the schedule; therefore, port skipping and swapping are necessary when multiple or longer disruptions occur at ports.

Since the port disruption is difficult to forecast, we attempt to take the uncertainties into account to achieve more meaningful results. To the best of our knowledge, there is barely a research study focusing on the uncertain port disruptions in the SSRP. Moreover, this is the first paper that applies distributionally robust optimization (DRO) to deal with uncertain port disruptions through the equivalent counterpart of DRO with polyhedral ambiguity set, in which a robust mean-CVaR optimization formulation is adopted as the objective function for a trade-off between the expected total costs and the risk.