Search results

IN many of the industrial and other aggressive environmental conditions encountered today a synthetic, plastics‐type of paint system must be used, since traditional paints give poor and limited service. However, for these synthetic paints to be fully effective, they must be applied to more scrupulously prepared surfaces. The finer tolerances and more exacting application requirements of synthetic plastics‐type coatings, such as the epoxies, must be appreciated. Once these are understood it is not difficult to put the materials into use, where they give outstanding long‐term protection. Some of the physical, chemical and solvent‐resistance characteristics of the epoxy resin coatings can, of course, be attained with other synthetic paints, and all these materials have their place in the paint manufacturer's armoury. There are resins showing better flexibility and chemical or heat resistance than the epoxies, but the latter are outstanding in combining these and other characteristics to a marked degree—hence their fairly rapid user acceptance. There is inevitably over‐lapping in characteristics with other coatings, particularly the polyurethanes, and it is not claimed here that epoxy coatings can confer protection against all corrosive environments.

The dispersity of graphene oxide (GO) has an important effect on the properties of epoxy resin (EP) composites. Many modification and dispersion methods require the use of inert solvents which do not participate in the modification reaction, although GO can be uniformly dispersed in water and alcohol solvents. Based on this requirement, several inert solvents were selected as dispersion solvents to find out the suitable inert solvent for GO dispersion into EP matrix.

Several inert solvents with different solubility parameters were selected as dispersion solvents to prepare GO/EP composite. The microstructure, mechanical properties, insulation properties, dielectric properties and thermal property of the composite were characterized, which was due to find suitable inert solvent for GO dispersion into EP matrix.

The dispersity of N, N-dimethylformamide (DMF) was the best stable suspension state when it was used as solvent instead of occurring sedimentation and agglomeration. Moreover, DMF was further confirmed as a suitable inert solvent for the dispersion of GO into EP according to the mechanical properties, insulation properties and thermal conductivity characterization.

The dispersion of GO in solvents has already been researched, but the traditional solvents, such as alcohols and water, has shown their limitations with the increase of modification methods, which were not suitable for the modification environment such as cyanate graft modification. Therefore, it was very important to choose a kind of inert solvent for dissolving EP matrix and dispersing GO better.

Several inert solvents were used to disperse GO into EP, and the influence of different dispersing solvents on the adhesive was discussed through the analysis of the mechanical properties, insulation properties and thermal conductivity, which was due to explore the inert solvent suitable for GO dispersion.

Introduction Most corrosion protection systems used for maintenance, as well as binders for the building and civil engineering industries, are cold‐curing formulations. Elevated temperature cure is usually excluded by the size and shape of the substrate to be coated. Consequently, the selection of binders that are suitable for these surface protection systems is limited to those that combine the following properties:

The ink maker and printer are vitally concerned with the behaviour to be expected from a pigment in terms of its contribution to printing properties (such as rheology, bleeding, damping water incompatibility), print appearance (colour, lustre), and useful service life (fading, resistance to chemical attack). Although practical printing tests can properly demonstrate the ultimate utility of a pigment for an intended use, sufficient preliminary data can normally be assembled to suggest candidate pigments suitable for evaluation.

The new raw materials which have appeared in the two years have been heavily weighted towards water‐based coatings. Thus, these will be emphasised in the discussion that follows. Also of considerable interest are a variety of new solvent‐based acrylic raw materials. Beyond this, there has been only modest variations of existing products useful in the formulation of coatings.

The formulation of industrial finishes to protect and improve the appearance of mass‐produced articles has become an increasingly complicated technique with the growing range of materials flow available. In this article Mr. Macrae, after discussing surface preparation and application methods, describes the formulation and performances of stoving enamels, cold‐curing finishes and air‐drying finishes. He concludes that even with the number of resins available today there is still much room for improvement.

If the paint chemist is to meet the challenges of ecology, toxicity, and government regulations generally, he must rely on two things. One of these is formulating skill, the other, new raw materials. In fact, however, there have been very few truly new raw materials in the past decade. Most of the advances have involved variations of known products and these variations have related to the needs of the paint chemist. For example there has been a strong desire to convert materials which are normally solvent‐based to forms useful in water‐borne compositions.

The paper aims to discuss the evaluation of anti-corrosive efficiency of conducting polymer, polypyrrole in water borne epoxy-polyamine coatings.

Polypyrrole (PPy) is synthesised by chemical oxidative polymerisation. The synthesised PPy is characterised by employing FT-IR, XRD, SEM and EDX analysis. The coatings are formulated using water borne epoxy cross-linked with aliphatic polyamine adduct and the effect of PPy on corrosion prevention is studied. PPy was used as anti-corrosive pigment in concentration varying from 1 to 5 wt.%. In addition to anti-corrosive property; mechanical properties, chemical resistance and weathering properties of the coatings containing PPy are studied, thereby obtaining a wholesome data about the quality and performance of these coatings.

The result obtained through various tests showed that the coating with 1 and 2% PPy exhibited excellent weathering resistance, mechanical properties and improved chemical resistance. Higher percentage loading of PPy (beyond 3 per cent) proves to be disastrous, as extended percolation networks are formed which results in rapid intense corrosion leading to fast coating breakdown.

The anti-corrosion property of the coating can be tested by means of atmospheric exposure such as Florida test which produces a real time evaluation of the anti-corrosive nature of the coating at natural condition rather than accelerated weathering, thereby providing more reliable performance data for intended application purpose.

The results find application in anti-corrosive/performance paints for industrial application.

This research paper presents the results of anti-corrosion behaviour of PPy in water borne epoxy-polyamide coating. Based on this result, a highly effective anti-corrosive coating can be formulated by the addition of small percentage of PPy in combination with other conventional pigments, thereby enhancing corrosion protection. But care must be taken so as to avoid formation of extended percolation network of PPy which leads to rapid coating breakdown.

For conservation of petochemical solvents and reduction of air pollution, the water soluble polymers will play an important role in surface coating industry. The coatings based on water soluble polymers are thinned with water instead of petroleum solvent. Basically, the water based coatings may be made from oils, alkyds, polyesters, aminoes, phenolics, epoxies and acrylics. In spite of a large number of other synthetic resins being available for use in coating formulations, the alkyd resins surpass all of them in versatility, and low cost; combining a broad spectrum of performance properties with economy. Water soluble alkyd resins are similar to their solvent borne counterparts. The major difference is that their formulation is modified to introduce pendant carboxylic acid groups along the polymer backbone. These pendant acid groups can be neutralised with basic compounds to produce water solubility. Several workers studied preparation and evaluation of film characteristics of water soluble alkyd resins using various types of polybasic acids, polyhydric alcohols and fatty acids. The curing of these resins has been satisfactorily accomplished by stoving in presence of water soluble amino resins.

It has been estimated that corrosion costs British industry some £1400 million a year, and it is considered that up to 25% of these costs could be eliminated by better application of existing knowledge of methods of corrosion prevention, much of it by the correct application of suitable anti‐corrosion coatings. Many of the most suitable anti‐corrosion coatings that can be used in chemical plant construction and maintenance are based on epoxy resins.