Search results

The purpose of this study is to investigate the sealing performance of different deep groove mechanical seals by considering the changing law of dynamic pressure effect and temperature gradient caused by high speed and high pressure.

A thermohydrodynamic lubrication model (THD) of the mechanical seal was constructed and solved using the commercial software FLUENT. The pressure and temperature distributions of the fluid under different groove types, as well as the sealing performance under different pressures, rotational speeds and sealing gaps, are obtained.

The annular groove (AG) can effectively reduce the temperature, and the T-type spiral groove (STG) can effectively inhibit the leakage. The increase of pressure and rotational speed leads to the enhancement of dynamic pressure effect and the increase of leakage, while the sealing gap increases and the leakage increases while taking away more heat. The choice of groove type is very important to the impact of sealing performance.

In consideration of the beneficial effect of deep grooves on cooling performance, the viscous temperature equation and the impact of the thermodynamic lubrication model are evaluated in conjunction with the sealing performance of four distinct groove types. This approach provides a theoretical basis for the optimal design of mechanical seals.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-05-2024-0184/

Two friction models of Fe-Fe and Diamond-like carbon (DLC)-Fe were established by molecular dynamics (MD) method to simulate the friction behavior of traditional fracturing pump plunger and new DLC plunger from atomic scale. This paper aims to investigate the effects of temperature and load on the friction behavior between sealed nitrile butadiene rubber (NBR) and DLC films.

In this study, MD method is used to investigate the friction behavior and mechanism of DLC film on plungers and sealing NBR based on Fe-Fe system and DLC-Fe system.

The results show that the friction coefficient of DLC-Fe system exhibits a downward trend with increasing load and temperature. And even achieve a superlubricity state of 0.005 when the load is 1 GPa. Further research revealed that the low interaction energy between DLC and NBR promoted the proportion of atoms with larger shear strain in NBR matrix and the lower Fe layer in DLC-Fe system to be much lower than that in Fe-Fe system. In addition, the application of DLC film can effectively inhibit the temperature rise of friction interface, but will occur relatively large peak velocity.

In this paper, two MD models were established to simulate the friction behavior between fracturing pump plunger and sealing rubber. Through the analysis of mean square displacement, atomic temperature, velocity and Interaction energy, it can be seen that the application of DLC film has a positive effect on reducing the friction of NBR.

This study aims to investigate the influence mechanism of thermal-mechanical deformations on the CO₂ mixture gases dry gas seal (DGS) flow field and compare the deformation characteristics and sealing performance between two-way and one-way thermal-fluid-solid coupling models.

The authors established a two-way thermal-fluid-solid coupling model by using gas film thickness as the transfer parameter between the fluid and solid domain, and the model was solved using the finite difference method and finite element method. The thermal-mechanical deformations of the sealing rings, the influence of face deformation on the flow field and sealing performance were obtained.

Thermal-mechanical deformations cause a convergent gap between the two sealing end faces, resulting in an increase in the gas film thickness, but a decrease in the gas film temperature and sealing ring temperature. The axial relative deformations of rotating and stationary ring end faces caused by mechanical and thermal loads in the two-way coupling model are less than those in the one-way coupling (OWC) model, and the gas film thickness and leakage rate are larger than those in the OWC model, whereas the gas film stiffness is the opposite.

This paper provides a theoretical support and reference for the operational stability and structural optimization design of CO₂ mixture gases DGS under high-pressure and high-speed operation conditions.

The purpose of this paper is to improve the seal performance by proper design of the cavity shape of the damping holes, especially the rotordynamics characteristics of the hole-pattern damped seal (HPDS).

A new damping seal structure that comprises a circle-shaped cavity and two directional leaf-shaped cavities with a dovetail-shaped diversion groove is proposed. The comparative study on the sealing characteristics of dovetail-shape, leaf-shape and classical circular HPDSs was carried out using ANSYS CFX.

The dovetail-shaped HPDS significantly outperformed two other damping seal designs in leakage and rotordynamic performance. At a rotating speed of 7,500 rpm, it showed a 25% reduction in leakage, a 23% increase in average effective damping and a 119% increase in average effective stiffness. The cross-coupled stiffness K_xy shifted from positive to negative, reducing circumferential flow. The dovetail's inclined leaf-shaped grooves create a double vortex that slows jet velocity in the seal clearance and alters spiral flow direction, resulting in a uniform pressure distribution and enhanced rotor stability at low frequencies.

This study proposes a novel HPDS with dovetail-shaped diversion grooves. The seal can realize the simultaneous improvement of rotordynamics and leakage characteristics compared to the current seal structure.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-04-2024-0127/

This paper aims to prepare an oil-impregnated porous polytetrafluoroethylene (PTFE) composite with advanced tribological properties using citric acid as a novel pore-forming agent.

Citric acid (CA) was used to form pores in PTFE, and then oil-impregnated PTFE composites were prepared. The pore-forming efficiency of CA was evaluated. The possible mechanism of lubrication was proposed according to the tribological properties.

The results show CA is an efficient pore-forming agent and completely removed, and the porosity of the PTFE increases with the increase of the CA content. The oil-impregnated porous PTFE exhibits an excellent tribological performance, an increased wear resistance of 77.29% was realized in comparison with neat PTFE.

This study enhances understanding of the lubrication mechanism of oil-impregnated porous polymers and guides for their tribological applications.

The effects of dust exposure in buildings and its health and comfort consequences continue to concern occupants, particularly those who spend most of their time indoors. This study examines the influence of building opening characteristics on surface dust loading in indoor environments to determine the dust particles' impact on different opening configurations.

Indoor Harmattan dust surface loading data were collected from Maiduguri, Northeastern Nigeria, using model rooms with six different window configurations. A simple mathematical relationship was employed to assess surface dust loading characteristics in the model rooms. The study measured dust thrice between December and February for three days (72 h). The results were analyzed using descriptive statistics.

The results determined the highest average surface dust loading of 12.03 g/m2 in the room with awning windows at an indoor-to-outdoor (I/O) ratio of 0.7. In contrast, the experiment in the room with a closed window recorded the lowest average surface dust loading of 5.24 g/m2 at an I/O ratio of 0.30, which is infiltration. The outcomes further indicate that the average surface dust loading varies with the building opening type and position, as higher surface dust loadings were recorded in locations closer to the openings (doors and windows), reaffirming that the dominant source of the dust particles is outdoors. According to the study, dust incursion due to infiltration accounts for 30% of the outdoor surface loading.

Thus, Harmattan dust is a serious challenge to the health, productivity and hygiene of building occupants in the study area. The built-environment professionals must use the study's outcome to optimize building openings' designs (shape, size and form) for effective indoor dust control.

This paper aims to find the best method to predict the friction coefficient of textured 45# steel by comparing different machine learning algorithms and analytical calculations.

Five machine learning algorithms, including K-nearest neighbor, random forest, support vector machine (SVM), gradient boosting decision tree (GBDT) and artificial neural network (ANN), are applied to predict friction coefficient of textured 45# steel surface under oil lubrication. The superiority of machine learning is verified by comparing it with analytical calculations and experimental results.

The results show that machine learning methods can accurately predict friction coefficient between interfaces compared to analytical calculations, in which SVM, GBDT and ANN methods show close prediction performance. When texture and working parameters both change, sliding speed plays the most important role, indicating that working parameters have more significant influence on friction coefficient than texture parameters.

This study can reduce the experimental cost and time of textured 45# steel, and provide a reference for the widespread application of machine learning in the friction field in the future.

This paper aims to reveal the influence of the grooved texture parameters on the lubrication performance of circular pocket-roller pairs in cylindrical roller bearings.

In this paper, the thermal elastohydrodynamic lubrication mathematical model of the grooved texture circular pocket-roller pair was established, the finite difference method and successive over-relaxation method were used to solve the model, the influence of texture quantity, texture depth and texture area ratio on circumferential bearing capacity, friction coefficient, maximum temperature rise, stiffness and damping of the circular pocket-roller pairs were analyzed.

The results show that texture quantity, texture depth and texture area ratio significantly influence the static and dynamic characteristics of circular pocket-roller pairs. The suitable surface groove texture parameters can dramatically improve the circumferential bearing capacity, reduce the friction coefficient, inhibit the maximum temperature rise and increase the stiffness and damping of the circular pocket-roller pairs.

The research in this paper can provide a theoretical basis for the optimization design of pockets in cylindrical roller bearings to reduce friction and vibration.

This study aims to develop a novel design method to make personalized masks for the effective prevention of pandemic respiratory infectious disease.

The changes in facial shape during speaking were analyzed using a three-dimensional (3D) scanning technique. In total, 13 anthropometric items were measured, and mask patterns were generated using a parametric pattern design method. Three sizing methods were proposed to reflect not only static but also dynamic body dimensions on the mask patterns.

A significant increase or decrease was observed in 10 out of 13 measurement items. Based on this, four items were selected to be used in the mask pattern design. The nose and cheek areas of a mask were fixed to protect the respiratory tract against viruses. The lower jaw area was deformed to improve the fit.

This study is expected to provide fundamental data to understand the changes in facial shape during movement. In addition, it is expected that the development of individualized personal protective equipment with movement adaptability will facilitate an effective response to various pandemic respiratory diseases.

In order to develop a personal protective equipment (PPE) that has a good fit and can protect against pandemic respiratory infectious diseases, morphological analysis was attempted using 3D facial data. It would be possible to design various products and equipment to be worn on the face by using the method proposed in this study.

This paper aims to control the deformation of a thin wall CrZrCu cylinder components (wall thickness 5 mm, diameter 400 mm) during thermal spray alumina-titania (AT13) coating by adjusting the spray parameters without deteriorating its quality evidently.

The deformation was controlled by lowering the temperature of the component in the way of adjusting the spray parameters. The main parameters adjust included extending the spraying distance, from normally 120 mm to 140 mm, decreasing plasma power from 50to 42 kW. An alumina-titanium (AT13) ceramic coating was chosen for protecting the substrate from corrosion. Microscopic morphology and phase analysis, insulation resistance testing, neutral salt test and electrochemical method were used to analyze the anti-corrosion and insulation performances of the coating.

The results indicate that, after adjusting the spraying parameters, the coating has a relatively high porosity, with an average value of 8.96 ± 0.77%. The bonding strength of the coating is relatively low, with an average value of 17.69 ± 0.85 MPa. However, after sealing, the polarization resistance of the coating in seawater can be maintained above 6.25 × 10⁶ Ω.cm² for an extended period. The coating has a high resistance (=1.1 M Ω), and there is no apparent galvanic corrosion when contacted with TC4 alloy. Additionally, analysis of corrosion products on the sample surface reveals that the samples with sprayed alumina-titanium ceramic show no copper corrosion products on the surface, and the coating remains intact, effectively isolating the corrosive medium.

By adjusting the spraying parameters, the deformation of the cylinder thin-walled component can be effectively controlled, making the φ 400 × 392 mm (thickness 5 mm) CrZrCu cylinder com-ponent with a maximum diameter deformation of only 0.14 mm. The satisfactory corrosion performances can be achieved under adjusting spraying parameters, which can guarantee the application of ceramic coating for weapon launching system of naval ships.