Search results
1 – 10 of 195Wei Jiang, Ray C. Chang, Ning Yang and Ying Xu
The purpose of this paper is to present a comparative study of flight circumstances, dynamic stability characteristics and controllability for two transport aircraft in severe…
Abstract
Purpose
The purpose of this paper is to present a comparative study of flight circumstances, dynamic stability characteristics and controllability for two transport aircraft in severe atmospheric turbulence at transonic cruise flight for the purpose to obtain the prevention concepts of injuries to passengers and crew members for pilot training in International Air Transport Association (IATA) – Loss of Control In-flight (LOC-I) program.
Design/methodology/approach
A twin-jet and a four-jet transport aircraft encountering severe atmospheric turbulence are the study cases for this paper. The nonlinear unsteady aerodynamic models are established through flight data mining and the fuzzy-logic modeling technique based on the flight data of flight data recorder. This method can be adopted to examine the influence of horizontal wind shear and crosswind on loss of control, dynamic stability characteristics and controllability for transport aircraft in different weights and different sizes in tracking aviation safety of existing different types of aircraft.
Findings
The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiate the sudden plunging motion during the turbulence encounter. The roll rate will increase the oscillatory rolling motion during plunging motion, if the rolling damping is insufficient. The drop-off altitude will be enlarged by the oscillatory rolling motion during the sudden plunging motion.
Research limitations/implications
A lack of the measurement data of vertical wind speed sensor on board to verify the estimated values of damping term is one of the research limitations for this study. The fact or condition of being severe in sudden plunging motion can be judged through the analysis of oscillatory derivatives with both dynamic stability and damping terms.
Practical implications
The roll rate will increase the oscillatory rolling motion during plunging motion, if the rolling damping is insufficient. The drop-off altitude will be enlarged by the oscillatory rolling motion during the sudden plunging motion. The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiated the sudden plunging motion during the turbulence encounter. If the drift angle is large, to turn off the autopilot of yaw control first and stabilize the rudder by the pedal. When passing through the atmosphere turbulence area, the pilots do not need to amend the heading angle urgently.
Social implications
The flight safety prevention in avoidance of injuries for passengers and cabin crews is essential for the airlines. The horizontal wind shear or crosswind before the turbulence encounter will easily induce rolling motion and then initiated the sudden plunging motion during the turbulence encounter.
Originality/value
The flight safety prevention in avoidance of injuries for passengers and cabin crews is essential. The present assessment method is an innovation to examine the loss of control problems of aviation safety and promote the understanding of aerodynamic responses of the jet transport aircraft. It is expected to provide a valuable lecture for the international training courses for IATA – LOC-I program after this paper is being published.
Details
Keywords
Huang Taiming, JingMao Ma, Li Zhang, Pan Hao, MingChen Feng, Wei Zeng and Changjie Ou
The purpose of this study is investigate the transient aerodynamic characteristics of high-speed vehicle with body roll motion under crosswind condition to improve aerodynamic…
Abstract
Purpose
The purpose of this study is investigate the transient aerodynamic characteristics of high-speed vehicle with body roll motion under crosswind condition to improve aerodynamic stability.
Design/methodology/approach
An overset mesh was used to simulate the rolling motion of the vehicle body. A wind tunnel experiment was conducted to validate the numerical method.
Findings
The results revealed that the vehicle’s aerodynamic characteristics changed periodically with the body’s periodic motion. In the absence of crosswind, the pressure distribution on the left and right sides of the vehicle body was symmetrical, and the speed streamline flowed to the rear of the vehicle in an orderly manner. The maximum aerodynamic lift observed in the transient simulation was −0.089, which is approximately 0.70 times that of the quasi-static simulation experiment. In addition, the maximum aerodynamic side force observed in the transient simulation was 0.654, which is approximately 1.25 times that of the quasi-static simulation experiment.
Originality/value
The aerodynamic load varies periodically with the vehicle body’s cyclic motion. However, the extreme values of the aerodynamic load do not occur when the vehicle body is at its highest or lowest position. This phenomenon is primarily attributed to the mutual interference of airflow viscosity and the hysteresis effect in the flow field, leading to the formation of a substantial vortex near the wheel. Consequently, the aerodynamic coefficient at each horizontal position becomes inconsistent during the periodic rolling of the vehicle body.
Details
Keywords
Heji Zhang, Dezhao Lu, Wei Pan, Xing Rong and Yongtao Zhang
The purpose of this study is to design a closed hydrostatic guideway has the ability to resist large-side load, pitch moments and yaw moments, has good stiffness and damping…
Abstract
Purpose
The purpose of this study is to design a closed hydrostatic guideway has the ability to resist large-side load, pitch moments and yaw moments, has good stiffness and damping characteristics, and provides certain beneficial guidance for the design of large-span closed hydrostatic guideway on the basis of providing a large vertical load bearing capacity.
Design/methodology/approach
The Reynolds’ equation and flow continuity equation are solved simultaneously by the finite difference method, and the perturbation method and the finite disturbance method is used for calculating the dynamic characteristics. The static and dynamic characteristics, including recess pressure, flow of lubricating oil, carrying capacity, pitch moment, yaw moment, dynamic stiffness and damping, are comprehensively analyzed.
Findings
The designed closed hydrostatic guideway has the ability to resist large lateral load, pitch moment and yaw moment and has good stiffness and damping characteristics, on the basis of being able to provide large vertical carrying capacity, which can meet the application requirements of heavy two-plate injection molding machine (TPIMM).
Originality/value
This paper researches static and dynamic characteristics of a large-span six-slider closed hydrostatic guideway used in heavy TPIMM, emphatically considering pitch moment and yaw moment. Some useful guidance is given for the design of large-span closed hydrostatic guideway.
Details
Keywords
Javad Masrour, Seyed Hossein Sadati and Morteza Shahravi
This study aims to simulate gust effects on the aeroelastic behavior of a flexible aircraft. The dynamic response of the system for different discreet gust excitations is obtained…
Abstract
Purpose
This study aims to simulate gust effects on the aeroelastic behavior of a flexible aircraft. The dynamic response of the system for different discreet gust excitations is obtained using numerical simulations.
Design/methodology/approach
Coupled dynamics, including rigid and flexible body coordinates, are considered for modeling the dynamic behavior of the aircraft. Wing is considered flexible and other parts are considered rigid. Wing is modeled with nonlinear Euler Bernoulli beam. Moreover, unsteady aerodynamics based on the Wagner function are used for aerodynamic loading, and the results are compared with those of quasi-steady aerodynamics.
Findings
Von Kármán continuous gust is applied to this aircraft. In addition, the discrete “1- cosine” gust with different gust lengths is applied to the aircraft, and the maximum and minimum accelerations are computed. It is shown that the nonlinear modeling of the system represents the actual behavior and causes limit cycle oscillation phenomena.
Originality/value
This methodology can yield a relatively simple dynamic model for high aspect ratio aircrafts to provide insights into the vehicles’ dynamics, which can be available early in the design cycle.
Details
Keywords
Yue Qiao, Wang Wei, Yunxiang Li, Shengzui Xu, Lang Wei, Xu Hao and Re Xia
The purpose of this paper is to introduce a motion control method for WFF-AmphiRobot, which can effectively realize the flexible motion of the robot on land, underwater and in the…
Abstract
Purpose
The purpose of this paper is to introduce a motion control method for WFF-AmphiRobot, which can effectively realize the flexible motion of the robot on land, underwater and in the transition zone between land and water.
Design/methodology/approach
Based on the dynamics model, the authors selected the appropriate state variables to construct the state space model of the robot and estimated the feedback state of the robot through the maximum a posteriori probability estimation. The nonlinear predictive model controller of the robot is constructed by local linearization of the model to perform closed-loop control on the overall motion of the robot. For the control problem of the terminal trajectory, using the neural rhythmic movement theory in bionics to construct a robot central pattern generator (CPG) for real-time generation of terminal trajectory.
Findings
In this paper, the motion state of WFF-AmphiRobot is estimated, and a model-based overall motion controller for the robot and an end-effector controller based on neural rhythm control are constructed. The effectiveness of the controller and motion control algorithm is verified by simulation and physical prototype motion experiments on land and underwater, and the robot can ideally complete the desired behavior.
Originality/value
The paper designed a controller for WFF-AmphiRobot. First, when constructing the robot state estimator in this paper, the robot dynamics model is introduced as the a priori estimation model, and the error compensation of the a priori model is performed by the method of maximum a posteriori probability estimation, which improves the accuracy of the state estimator. Second, for the underwater oscillation motion characteristics of the flipper, the Hopf oscillator is used as the basis, and the flipper fluctuation equation is modified and improved by the CPG signal is adapted to the flipper oscillation demand. The controller effectively controls the position error and heading angle error within the desired range during the movement of the WFF-AmphiRobot.
Details
Keywords
Shima Yazdani, Erfan Salimipour, Ayoob Salimipour, Mikhail A. Sheremet and Mohammad Ghalambaz
Active flow control on the NACA 0024 airfoil defined as suction-injection jet at the chord-based Reynolds number of 1.5 × 1e + 5 is studied.
Abstract
Purpose
Active flow control on the NACA 0024 airfoil defined as suction-injection jet at the chord-based Reynolds number of 1.5 × 1e + 5 is studied.
Design/methodology/approach
The three-dimensional incompressible unsteady Reynolds-averaged Navier–Stokes equations with the SST k-ω turbulence model are used to study the effects of coflow-jet (CFJ) on the dynamic and static stall phenomena. CFJ implementation is conducted with several momentum coefficients to investigate their turnover. Furthermore, the current work intends to analyze the CFJ performance by varying the Reynolds number and jet momentum coefficient and comparing all states to the baseline airfoil, which has not been studied in prior research investigations.
Findings
It is observed that at the momentum coefficient (Cµ) of 0.06, the lift coefficients at low attack angles (up to a = 15) dramatically increase. Furthermore, the dynamic stall at the given Reynolds number and with the lowered frequency of 0.15 is explored. In the instance of Cµ = 0.07, the lift coefficient curve does not show a noticeable stall feature compared to Cµ = 0.05, suggesting that a more powerful stronger jet can entirely control the dynamic stall.
Originality/value
Furthermore, the current work intends to analyze the CFJ performance by varying the jet momentum coefficient and comparing all states to the baseline airfoil, which has not been studied in prior research investigations.
Details
Keywords
Xinyang Fan, Xin Shu, Baoxu Tu, Changyuan Liu, Fenglei Ni and Zainan Jiang
In the current teleoperation system of humanoid robots, the control between arms and the control between the waist and arms are individual and lack coordinated motion. This paper…
Abstract
Purpose
In the current teleoperation system of humanoid robots, the control between arms and the control between the waist and arms are individual and lack coordinated motion. This paper aims to solve the above problem and proposes a teleoperation control approach for a humanoid robot based on waist–arm coordination (WAC).
Design/methodology/approach
The teleoperation approach based on WAC comprises dual-arm coordination (DAC) and WAC. The DAC method realizes the coordinated motion of both arms through one hand by establishing a mapping relationship between a single hand controller and the manipulated object; the WAC method realizes the coordinated motion of both arms and waist by calculating the inverse kinematic input of robotic arms based on the desired velocity of the waist and the end of both arms. An integrated teleoperation control framework provides interfaces for the above methods, and users can switch control modes online to adapt to different tasks.
Findings
After conducting experiments on the dual-arm humanoid robot through the teleoperation control framework, it was found that the DAC method can save 27.2% of the operation time and reduce 99.9% of the posture change of the manipulated object compared with the commonly used individual control. The WAC method can accomplish a task that cannot be done by individual control. The experiments proved the improvement of both methods in terms of operation efficiency, operation stability and operation capability compared with individual control.
Originality/value
The DAC method better maintains the constraints of both arms and the manipulated object. The WAC method better maintains the constraints of the manipulated object itself. Meanwhile, the teleoperation framework integrates the proposed methods and enriches the teleoperation modes and control means.
Details
Keywords
Guodong Qin, Qi Wang, Changyang Li, Aihong Ji, Huapeng Wu, Zhikang Yang and Shikun Wen
In large equipment and highly complex confined workspaces, the maintenance is usually carried out by snake-arm robots with equal cross-sections. However, the equal cross-sectional…
Abstract
Purpose
In large equipment and highly complex confined workspaces, the maintenance is usually carried out by snake-arm robots with equal cross-sections. However, the equal cross-sectional design results in the snake arm suffering from stress concentration and restricted working space. The purpose of this paper is to design a variable cross-section elephant trunk robot (ETR) that can address these shortcomings through bionic principles.
Design/methodology/approach
This paper proposes a cable-driven ETR to explore the advantages and inspiration of variable cross-section features for hyper-redundant robot design. For the kinematic characteristics, the influence of the variable cross-section design on the maximum joint angle of the ETR is analysed using the control variables method and the structural parameters are selected. Based on the biological inspiration of the whole elephant trunk following the movement of the trunk tip, a trajectory-tracking algorithm is designed to solve the inverse kinematics of the ETR.
Findings
Simulation and test results show the unique advantages of the proposed variable cross-section ETR in kinematics and forces, which can reduce stress concentrations and increase the flexibility of movement.
Originality/value
This paper presents a design method for a variable cross-section ETR for confined working spaces, analyses the kinematic characteristics and develops a targeted trajectory control algorithm.
Details
Keywords
Xiaoxue Liu, Yuchen Liu, Youwei Zhang and Hanfei Guo
According to relevant research, non-uniform speed has a significant impact on the vehicle-track systems. Up to now, research work on it is still very limited. In this paper, the…
Abstract
Purpose
According to relevant research, non-uniform speed has a significant impact on the vehicle-track systems. Up to now, research work on it is still very limited. In this paper, the PEM is adopted to further transform it into a deterministic process to solve the vehicle’s problem of running at a non-uniform speed.
Design/methodology/approach
The multi-body vehicle model has 10 degrees of freedom and the track is regarded as a finite long beam supported by lumped sleepers and ballast blocks. They are connected via linear Hertz springs. The vertical track irregularity is a Gaussian stationary process in the space domain. It is transformed into a uniformly modulated nonstationary random process in the time domain with respect to the non-uniform vehicle speed. By solving the equation of motion of the coupled vehicle-track system with the pseudo-excitation method, the pseudo-response and consequently the power spectral density and the standard deviation of the structural response can be obtained.
Findings
Two kinds of vehicle braking programs are taken in the numerical example and some beneficial conclusions are drawn.
Originality/value
The pseudo-excitation method (PEM) was used to perform the random vibration analysis of a coupled non-uniform speed vehicle-track system. Transforming the track irregularity into a uniformly modulated nonstationary random process in time domain with respect to the non-uniform vehicle speed was undertaken. The pseudo-response of the coupled system is solved by applying the Newmark algorithm with constant space integral steps. The random vibration transfer mechanism of the coupled system is fully discussed.
Details
Keywords
Massicilia Dahmani, Abdelghani Seghir, Nabil Issaadi and Ouali Amiri
This study aims to propose a numerical modeling procedure for response analysis of elastic body floating in water and submitted to regular waves. An equivalent simplified…
Abstract
Purpose
This study aims to propose a numerical modeling procedure for response analysis of elastic body floating in water and submitted to regular waves. An equivalent simplified mechanical single-degree-of-freedom system allowing to reproduce the heave movements is first developed, then the obtained lumped characteristics are used for elastic analysis of the floating body in heave motion.
Design/methodology/approach
First, a two-dimensional numerical model of a rigid floating body in a wave tank is implemented under DualSPHysics, an open source computational fluid dynamics (CFD) code based on smoothed particle hydrodynamics method. Then, the obtained results are exploited to derive an equivalent mechanical mass-spring-damper model. Finally, estimated equivalent characteristics are used in a structural finite element modeling of the considered body assuming elastic behavior.
Findings
Obtained results concerning the floating body displacements are represented and validated using existing experimental data in the literature. Wave forces acting on the body are also evaluated. It was found that for regular waves, it is possible to replace the complex CFD refined model by an equivalent simplified mechanical system which makes easy the use of structural finite element analysis.
Originality/value
The originality of this work lies in the proposed procedure to evaluate the mechanical properties of the equivalent elastic system. This allows to couple two different software tools and to take advantages of their features.
Details