Search results

1 – 2 of 2
Article
Publication date: 17 April 2019

Erfan Khodabandeh, Davood Toghraie, A. Chamkha, Ramin Mashayekhi, Omidali Akbari and Seyed Alireza Rozati

Increasing heat transfer rate in spiral heat exchangers is possible by using conventional methods such as increasing number of fluid passes and counter flowing. In addition, newer…

Abstract

Purpose

Increasing heat transfer rate in spiral heat exchangers is possible by using conventional methods such as increasing number of fluid passes and counter flowing. In addition, newer ideas such as using pillows as baffles in the path of cold and hot fluids and using nanofluids can increase heat transfer rate. The purpose of this study is to simulate turbulent flow and heat transfer of two-phase water-silver nanofluid with 0-6 Vol.% nanoparticle concentration in a 180° path of spiral heat exchanger with elliptic pillows.

Design/methodology/approach

In this simulation, the finite volume method and two-phase mixture model are used. The walls are subjected to constant heat flux of q″ = 150,000 Wm−2. The inlet fluid enters curves path of spiral heat exchanger with uniform temperature Tin = 300 K. After flowing past the pillows and traversing the curved route, the working fluid exchanges heat with hot walls and then exits from the section. In this study, the effect of radiation is disregarded because of low temperature range. Also, temperature jump and velocity slipping are disregarded. The effects of thermophoresis and turbulent diffusion on nanofluid heat transfer are disregarded. By using finite volume method and two-phase mixture model, simulations are performed.

Findings

The results show that the flow and heat transfer characteristics are dependent on the height of pillows, nanoparticle concentration and Reynolds number. Increasing Reynolds number, nanoparticle concentration and pillow height causes an increase in Nusselt number, pressure drop and pumping power.

Originality/value

Turbulent flow and heat transfer of two-phase water-silver nanofluid of 0-6 per cent volume fraction in a 180° path of spiral heat exchanger with elliptic pillows is simulated.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 30 no. 4
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 24 October 2018

Hesam Bakhshi, Erfan Khodabandeh, Omidali Akbari, Davood Toghraie, Mohammad Joshaghani and Alireza Rahbari

In the present study, laminar steady flow of nanofluid through a trapezoidal channel is studied by using of finite volume method. The main aim of this paper is to study the effect…

Abstract

Purpose

In the present study, laminar steady flow of nanofluid through a trapezoidal channel is studied by using of finite volume method. The main aim of this paper is to study the effect of changes in geometric parameters, including internal and external dimensions on the behavior of heat transfer and fluid flow. For each parameter, an optimum ratio will be presented.

Design/methodology/approach

The results showed that in a channel cell, changing any geometric parameter may affect the temperature and flow field, even though the volume of the channel is kept constant. For a relatively small hydraulic diameter, microchannels with different angles have a similar dimensionless heat flux, while channels with bigger dimensions show various values of dimensionless heat flux. By increasing the angles of trapezoidal microchannels, dimensionless heat flux per unit of volume increases. As a result, the maximum and minimum heat transfer rate occurs in a trapezoidal microchannel with 75° and 30 internal’s, respectively. In the study of dimensionless heat flux rate with hydraulic diameter variations, an optimum hydraulic diameter (Dh) was observed in which the heat transfer rate per unit volume attains maximum value.

Findings

This optimum state is predicted to happen at a side angle of 75° and hydraulic diameter of 290 µm. In addition, in trapezoidal microchannel with higher aspect ratio, dimensionless heat flux rate is lower. Changing side angles of the channels and pressure drop have the same effect on pressure drop. For a constant pressure drop, if changing the side angles causes an increase in the rectangular area of the channel cross-section and the effect of the sides are not felt by the fluid, then the dimensionless heat flux will increase. By increasing the internal aspect ratio (t_2/t_3), the amount of t_3 decreases, and consequently, the conduction resistance of the hot surface decreases.

Originality/value

The effects of geometry of the microchannel, including internal and external dimensions on the behavior of heat transfer and fluid flow for pressure ranges between 2 and 8 kPa.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 29 no. 5
Type: Research Article
ISSN: 0961-5539

Keywords

1 – 2 of 2