Search results

To prevent the coil from burning or getting damaged, it is necessary to estimate the duration of its operation as long as its temperature does not exceed the permissible limit. This paper aims to investigate the effect of switching on the thermal behavior of impregnated and nonimpregnated windings. Also, the safe operating time for each winding is determined.

The power loss of the winding is expressed as a function of the winding specifications. Using homogenization techniques, the equivalent thermal properties for the homogenized winding are calculated and used in a proposed thermal equivalent circuit for winding modeling and analysis. The validity and accuracy of the proposed model are determined by comparing its analysis results and simulation and measurement results.

The results show that copper windings have better thermal behavior and lower temperature compared to aluminum windings. On the other hand, by impregnating or increasing the packing factor of the winding, the thermal behavior is improved. Also, by choosing the right duty cycle for the winding current source, it is possible to prevent the burning or damage of the winding and increase its lifespan. Comparing the measurement results with the analysis results shows that the proposed equivalent circuit has an error of less than 4% in the calculation of the winding center temperature.

In this paper, the effect of temperature on the electrical resistance of the coil is ignored. Also, rectangular wires were not investigated. Research in these topics are considered as future work.

By calculating the thermal time constant of the winding, its safe operation time can be calculated so that its temperature does not exceed the tolerable value (150 °C). The proposed method analyzes both impregnated and nonimpregnated windings with various schemes. It investigates the effects of switching on their thermal behavior. Additionally, it determines the safe operating time for each type of winding.

The purpose of this study is to achieve lower and lower temperature as infrared sensors works faster and better used for space application. For getting good quality images from space, the infrared sensors are need to keep in cryogenic temperature. Cooling to cryogenic temperatures is necessary for space-borne sensors used for space applications. Infrared sensors work faster or better at lower temperatures. It is the need for time to achieve lower and lower temperatures.

This study presents the investigation of the critical Stirling cryocooler parameters that influence the cold end temperature. In the paper, the design approach, the dimensions gained through thermal analysis, experimental procedure and testing results are discussed.

The effect of parameters such as multilayer insulation, helium gas charging pressure, compressor input voltage and cooling load was investigated. The performance of gold-plated and aluminized multilayer insulation is checked. The tests were done with multilayer insulation covering inside and outside the Perspex cover.

By using aluminized multilayer insulation inside and outside the Perspex cover, the improvement of 16 K in cool-down temperature was achieved. The cryocooler is charged with helium gas. The pressure varies between 14 and 18 bar. The optimum cooling is obtained for 17 bar gas pressure. The piston stroke increased as the compressor voltage increased, resulting in total helium gas compression. The optimum cool-down temperature was attained at 85 V.

The cryocooler is designed to achieve the cool-down temperature of 2 W cooling load at 100 K. The lowest cool-down temperature recorded was 105 K at a 2 W cooling load. Multilayer insulation is the major item that keeps the thermal radiation from the sun from reaching the copper tip.

This study aims to investigate the influences of polyester fabric layers on the mechanical properties of SBR and devulcanized waste rubber composite materials, as well as the effect of gamma irradiation dose.

The devulcanized waste rubbers (DWR) were carried out by different methods. First, chemically, by two different reclaiming agents such as tetramethylthiuram disulfide (TMTD) and 2-mercapto benzothiazole disulfide (MBTS). Secondary by a physical method like microwave (MW). The devulcanized rubbers were mixed with virgin styrene butadiene rubber (SBR) in different ratios, as follows: SBR-DWR (TMTD) 50 / 50, SBR-DWR (MBTS) 80 / 20 and SBR-DWR (MW) 80 / 20. A series of sandwich polyester tire cord fabrics were used as reinforcement for making SBR and devulcanized waste rubber composite materials and molded on a hot press into rubber sheet films, then subjected to gamma radiation at different doses ranging from 100 up to 200 kGy.

The experimental results indicate that increasing the layer number improves the mechanical properties of composites. The tensile strength, tearing, hardness and elastic modulus of the rubber composites increased with the rise of the fiber layers and by increasing the irradiation dose up to 200 kGy. The reclaiming agent TMTD gave the best results for mechanical properties, followed by MW and then MBTS.

This phenomenon can be detailed based on the fact that when the fiber-reinforced composites are subjected to loading, the fibers act as load carriers, depending on the population and orientation of the fibers. Also, scanning electron microscopy (SEM) reveals that adhesion was caused by tire cord fabrics and rubber blend matrix.

This paper aims to apply the non-linear impedance boundary condition (IBC) for a linear piecewise B–H curve in frequency domain simulations to find the equivalent impedance of a simple induction heating system model.

An electromagnetic description of the inductor system is performed to substitute the effects of the induction load, for a mathematical condition, the so-called IBC. This is suitable to be used in electromagnetic systems involving high conductive materials at medium frequencies, as it occurs in an induction heating system.

A reduction of the computational cost of electromagnetic simulation through the application of the IBC. The model based on linear piecewise B–H curve simplifies the electromagnetic description, and it can facilitate the identification of the induction load characteristics from experimental measurements.

This work is performed to assess the feasibility of using the non-linear boundary impedance condition of materials with linear piecewise B–H curve to simulate in the frequency domain with a reduced computational cost compared to time domain simulations.

In this paper, the use of the non-linear boundary impedance condition to describe materials with B–H curve by segments, which can approximate any dependence without hysteresis, has been studied. The results are compared with computationally more expensive time domain simulations.

The purpose of this study is to prepare a state-of-the-art review on advanced ceramic materials including their fabrication techniques, characteristics, applications and wettability.

This review paper presents the various types of advanced ceramic materials according to their compounding elements, fabrication techniques of advanced ceramic powders as well as their consolidation, their characteristics, applications and wetting properties. Hydrophobic/hydrophilic properties of advanced ceramic materials are described in the paper with their state-of-the-art application areas. Optical properties of fine ceramics with their intrinsic characteristics are also presented within. Special focus is given to the brief description of application-based manipulation of wetting properties of advanced ceramics in the paper.

The study of wetting/hydrophobicity/hydrophilicity of ceramic materials is important by which it can be further modified to achieve the required applications. It also makes some sense that the material should be tested for its wetting properties when it is going to be used in some important applications like biomedical and dental. Also, these advanced ceramics are now often used in the fabrication of filters and membranes to purify liquid/water so the study of wetting characteristics of these materials becomes essential. The optical properties of advanced ceramics are equally making them suitable for many state-of-the-art applications. Dental, medical, imaging and electronics are the few sectors that use advanced ceramics for their optical properties.

This review paper includes various advanced ceramic materials according to their compounding elements, different fabrication techniques of powders and their consolidation, their characteristics, various application area and hydrophobic/hydrophilic properties.