Search results

The purpose of this study is to investigate the influence of hemispherical structures fabricated by hot micro-coining on the resulting wear performance. Hemispherical structures with different area densities (20 and 30 per cent), depths (50 and 100 µm) and diameters (100 and 200 µm) were fabricated by hot micro-coining on stainless steel samples.

The wear performance of these samples was studied using a ball-on-disk tribometer in rotational sliding mode using a normal load of 30 N and a fixed sliding velocity of 2 cm/s. Two different poly-(alpha)-olefin (PAO) oils without any additive having a kinematic viscosity of 4 and 40 cSt, were used to study the influence of the oil viscosity on the wear behavior.

Concerning the polished reference, an enlarged wear volume with an increase in the cycle number and the oil viscosity was observed. In the case of the micro-coined surfaces, all samples demonstrate a pronounced reduction in the wear volume (up to a factor of 100 for PAO 40) compared to the polished reference irrespective of the oil viscosity used.

This study details new research work studying the wear behavior of hot micro-coined surfaces.

The paper aims to investigate the possibilities to control friction in lubricated systems by surface patterning, making use of a multi-scale approach. Surface patterns inside the tribological contact zone tend to directly reduce friction, whereas surface patterns located in the close proximity of the contact area can improve the tribological performance by avoiding lubricant starvation and migration. Finally, optimized surface patterns were identified by preliminary laboratory tests and transferred to a journal bearing, thus testing them under more realistic conditions.

Surface patterns on a large scale (depth > 10 µm) were fabricated by micro- and roller-coining, whereas surface patterns on a small scale (depth < 2 µm) were produced by direct laser interference patterning. The combination of both techniques resulted in multi-scale surface patterns. Tribologically beneficial surface patterns (verified in ball-on-disk laboratory tests) were transferred onto a journal bearing’s shaft and tested on a special test-rig. To characterize the lubricant spreading behavior, a new test-rig was designed, which allowed for the study of the lubricant’s motion on patterned surfaces under the influence of a precisely controlled temperature gradient.

All tested patterns accounted for a pronounced friction reduction and/or an increase in oil film lifetime. The results from the preliminary laboratory tests matched well, with results from the journal bearing test-rig, both tests showing a maximum friction reduction by a factor of 3-4. Numerical investigations, as well as experiments, have shown the possibility to actively guide lubricant over patterned surfaces. Smaller periodicities, as well as greater structural depths and widths, led to a more pronounced anisotropic spreading and/or greater spreading velocities. Multi-scale surfaces demonstrated the strongest effects regarding the lubricant’s spreading behavior.

Friction, as well as lubricant migration, can be successfully controlled by using micro-coined, laser-patterned and/or multi-scale surfaces. To the best of the authors’ knowledge, the study demonstrates for the first time the unique possibility to transfer results obtained in laboratory tests to a real machine component.

This paper aims to derive tailor-made microtextures for elastohydrodynamically lubricated (EHL) contacts under consideration of manufacturing possibilities.

Component tests were used for the evaluation of the influence of surface texturing on the friction behavior in the cam/tappet contact. Furthermore, the manufacturing possibilities and limitations of a combined μEDM and micro-coining process and the feasibility of integration into a forming process were studied. Finally, a methodology based on transient EHL simulations and a meta-model of optimal prognosis was exemplarily used for microtexture optimization.

It was found that surface texturing in EHL contacts with high amount of sliding is promising. Moreover, the combination of μEDM and micro coining and the integration into established production processes allow the manufacturing of microtextures with desirable structural parameters and sufficient accuracy.

This paper gives a holistic view on surface microtexturing over several phases of the product life cycle, from the design, over efficient manufacturing to application-related testing.

Public libraries across the country are adding a new component to their collections and services: the home computer. Below are several mini “case studies” describing the experiences of seven libraries with their computer collections.

The purpose of this paper is to use a combination of numerical simulation and experiment to evaluate the performance of laser surface texturing (LST) in the field of gear lubrication, and to more accurately predict the lubrication characteristics of different surfaces.

The method used in this paper is developed on the basis of the deterministic solution of the three-dimensional (3D) mixed elasto-hydrodynamic lubrication (EHL) model and the model parameters are corrected by friction test. The film pressure, film thickness and friction coefficient of different micro-textured tooth surfaces are predicted on the basis of accurate 3D mixed EHL models.

The results demonstrate that the micro-texture structure of the tooth surface can increase the local film thickness and enhance the lubricating performance of the tooth surface without drastically reducing the contact fatigue life. The stress distribution and friction characteristics of the tooth surface can be optimized by adjusting the micro-texture arrangement and the size of the micro-textures.

A new evaluation method using a 3D hybrid EHL model and friction test to predict the lubrication characteristics of LST is proposed, which can effectively improve the processing economy and save time.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2020-0423

This study aims to develop a new method to treat the numerical singularity at the critical nodes of two skew coordinates, and optimize the leakage of micro herringbone grooved journal bearings (MHGJBs) with this method.

A side leakage numerical algorithm is proposed by using the skew meshes with a virtual node (SMVN) method to evaluate the effects of groove angle, bank/groove ratio, groove depth and groove number on load capacity, friction and side leakage of MHGJB.

The SMVN method is effective in treating the numerical singularity at the critical nodes of two skew coordinates. Besides, a group of optimized parameters of micro herringbone groove is obtained which can not only minimize the side leakage but also improve the load capacity and friction force.

A virtual node method was proposed, which can significantly improve the calculation accuracy in the side leakage model.

The paper aims to explore the economic, political and social premises according to which some governmental agencies have decided to promote IC reporting in their country. Firstly, it will examine the contextual premises and conditions that have encouraged (or inhibited) IC reporting. Secondly, it will investigate the way these premises and conditions interact in different ways, thus establishing (loosely) coupled relationships.

The relationship between IC recommendation for corporate reporting and contextual linkages will be analysed from a political economy perspective, as proposed by Cooper and Sherer, and others, and as modified by the type of discursive analysis inspired by Burchell et al.

In light of the relationship that the paper will establish between different discourses, IC will be understood not as a merely corporate neutral technique but as an economic and socially constructed phenomenon aimed at re‐launching the growth of a country. In this way, it will be explored from both within – in terms of methods and their usefulness for its “supporters” – and also externally – in relation to how it is perceived and in turn communicated by politicians who are “delegates of different cognitive and social institutions”, as Manninen said in 1996.

A political economy analysis of IC reporting enables the opening up of the black box of IC reporting in relation to public policy, outlining a useful approach for practitioners and policy makers.

The purpose of this paper is to introduce the concept of stationary inlet zone bump (IZB) for film thickness enhancement in unidirectional pure sliding elastohydrodynamic lubrication (EHL) line contacts and to investigate the effects of maximum Hertzian pressure (load) and piezo-viscous response on the effectiveness of IZB.

The numerical analysis involves the solution of Reynolds and elasticity equations. The well-established Doolittle–Tait equations are used herein to determine the lubricant viscosity and density as functions of local pressure, while the Carreau model is used to describe the lubricant rheology. The IZB is assumed to have a sinusoidal profile and it is present on the stationary surface. The governing equations are discretized using finite difference scheme and solved using the Newton–Raphson technique.

Two test oils, L7808 and SR600, with linear and exponential piezo-viscous responses in the inlet zone are considered here for comparison. The effectiveness of IZB in terms of film thickness enhancement is found to be more for SR600. Besides, IZB is found to be more effective at lower values of maximum Hertzian pressure. The bump needs to shift downstream at higher load to be as effective as at lower load.

This is the first paper to simulate EHL characteristics in the presence of a stationary IZB and to study the effect of various parameters on EHL effectiveness. The film thickness enhancement obtained here is remarkable and hence it is a novel and valuable contribution.