Search results

This paper aims to develop a comprehensive model of a magnetic sensor array that will be operational for a multitude of electric components in continuous and nonintrusive condition monitoring (CM) or in readiness assessment (RA) applications.

A universal nonintrusive model of a flexible antenna array is introduced to monitor and identify failures in electric machine drives. An adjustable sensor is designed to serve as a RA for a vast range of electrical elements in a typical power system by capturing the low-frequency radiated magnetic fields.

The optimal placement of the most sensitive radiated fields from several components has been discovered in this case study, enabling the detection of healthy current flow throughout. Thereafter, the short-circuit investigation, representing faulty situations, is implemented and compared with healthy cases.

This sensing technique can be used for nonintrusive CM of components that are out of reach and cannot have the sensor to be held around it such as components in offshore winds, wind energy generation and power and chemical plants.

The results are provided for three commonly used machines with a single sensor array with numerous settings. The three dimensional (3 D) finite element analysis is applied in the structuring of the sensor, detection of the optimum location and recognition of faults in the machines. Finally, based on the setup design, 3 D printing is used for the construction of the sensor array. Thus, the sensor array with fault detection avoids major component failures and increases system reliability/resiliency.

The paper presents the Finite Element (FE) evaluation of the magnetic field emitted by a Wireless Power Transfer Systems used to charge the battery of electrical vehicles. An original approach for reducing the mesh size of the 3D FE model is used.

A minicar equipped with a circular coil is considered, while the transmitting coil is coherent with the Society of Automotive Engineers (SAE) standard. The different shape of the coils and a possible misalignment are considered as possible sources of emitted magnetic field, which a person could be exposed to. To this end, a FE model is implemented. Because of the complexity of the mesh, a suitable 3D model is used. This model is previously validated and then used for evaluating the magnetic field around the Wireless Power Transfer Systems (WPTS).

The magnetic flux density around the WPTS is calculated and compared with the International Commission on Non-Ionizing Radiation Protection (ICNIRP) limits.

The proposed 3D model, whose validation is shown in the paper, is able to compute the magnetic field with high accuracy despite the presence of a conductive and ferromagnetic thin structure, the steel layer related to the car frame, which would need a very fine mesh with a large number of elements to solve Maxwell equations.

Deals with aspects of analysis of 2D electromagnetic fields due to a power frequency through a pair of bars placed parallel to a conducting half‐space, above which there are two longitudinal magnetic shunts.

The areal (surface area density of bits) storage density of magnetic hard disks is continually increasing, with typical available commercial storage densities being around 10Gbits/in². It is predicted that densities in excess of 40Gbits/in² will be possible before the year 2003. A number of key issues arise from this development, such as the need to determine and control accurately the dynamic flying height (z‐axis) of the read‐write head, which is affected by the apparent distortion of the disk surface due to rotation‐induced disk resonance. As a result of the increasing storage density the positional control of the head in the plane of the disk (x‐y plane) also becomes more critical. This paper deals generally, but with a particular emphasis on optical and piezoelectric sensors used in our laboratory for characterisation of storage media and systems.

Roger Main gives a four‐part report on the optical technologies which are playing an increasingly important role in sensor development.

DURING THE DEVELOPMENT of Concorde from prototype aeroplanes through pre‐production to the full production standard, many design changes have been introduced to the 16 flight deck transparencies, which can be divided into three groups:

The aim of this work is to investigate the self-healing performance of epoxy coatings containing microcapsules. The microcapsule-based coatings were applied on AA6061 Al alloy and immersed in 3.5 per cent NaCl solution.

Microcapsules with urea–formaldehyde as the shell and linseed oil as the healing agent were prepared by in situ polymerization in an oil-in-water emulsion. For the sake of an optimum self-healing system, some coating samples were prepared by using different microcapsule concentrations: 0, 5, 10 and 20 Wt.%. The scratch-filling efficiency as the theoretical estimate of the self-healing performance was calculated for the coating samples with different microcapsule concentrations. The scratch-sealing efficiency (SSE) as a particularly crucial parameter in the self-healing evaluation of coatings was measured by both electrochemical impedance spectroscopy (EIS) and electrochemical noise (EN) techniques.

According to EIS and EN results, the coating samples containing 5 and 10 per cent microcapsules provided the insignificant self-healing performance, while the coating sample containing 20 per cent microcapsules exhibited the acceptable self-healing performance to AA6061 alloy in the NaCl solution. The measured SSE values confirmed the good agreement of EN data with electrochemical parameters obtained from the EIS technique.

This work is an attempt to evaluate the self-healing performance of microcapsule-based epoxy coatings applied on AA6061 Al alloy in sea water.

This paper aims to propose and establish a set of new benchmark models to investigate and confidently validate the modeling and prediction of total stray-field loss inside magnetic and non-magnetic components under harmonics-direct current (HDC) hybrid excitations. As a new member-set (P21^e) of the testing electromagnetic analysis methods Problem 21 Family, the focus is on efficient analysis methods and accurate material property modeling under complex excitations.

This P21^e-based benchmarking covers the design of new benchmark models with magnetic flux compensation, the establishment of a new benchmark measurement system with HDC hybrid excitation, the formulation of the testing program (such as defined Cases I–V) and the measurement and prediction of material properties under HDC hybrid excitations, to test electromagnetic analysis methods and finite element (FE) computation models and investigate the electromagnetic behavior of typical magnetic and electromagnetic shields in electrical equipment.

The updated Problem 21 Family (V.2021) can now be used to investigate and validate the total power loss and the different shielding performance of magnetic and electromagnetic shields under various HDC hybrid excitations, including the different spatial distributions of the same excitation parameters. The new member-set (P21^e) with magnetic flux compensation can experimentally determine the total power loss inside the load-component, which helps to validate the numerical modeling and simulation with confidence. The additional iron loss inside the laminated sheets caused by the magnetic flux normal to the laminations must be correctly modeled and predicted during the design and analysis. It is also observed that the magnetic properties (B27R090) measured in the rolling and transverse directions with different direct current (DC) biasing magnetic field are quite different from each other.

The future benchmarking target is to study the effects of stronger HDC hybrid excitations on the internal loss behavior and the microstructure of magnetic load components.

This paper proposes a new extension of Problem 21 Family (1993–2021) with the upgraded excitation, involving multi-harmonics and DC bias. The alternating current (AC) and DC excitation can be applied at the two sides of the model’s load-component to avoid the adverse impact on the AC and DC power supply and investigate the effect of different AC and DC hybrid patterns on the total loss inside the load-component. The overall effectiveness of numerical modeling and simulation is highlighted and achieved via combining the efficient electromagnetic analysis methods and solvers, the reliable material property modeling and prediction under complex excitations and the precise FE computation model using partition processing. The outcome of this project will be beneficial to large-scale and high-performance numerical modeling.

The purpose of this paper is to introduce a theoretical investigation of the pulse‐cathodic protection (PCP) systems to show how they behave under different operating conditions. The effectiveness of the PCP system also is highlighted for a typical large‐scale configuration. The principal technical objectives of this paper are to answer three questions: Are the PCP systems effective in the desert fields? Although they have been approved, what is the reason for their lack of effectiveness in some coastal areas? What are the operation recommendations for the currently installed PCP systems and their future application?

The factors affecting the cathodic protection of well casings have been investigated theoretically by using a 3D field approach software package current distribution, electromagnetic fields, grounding and soil structure analysis. Cathodic interference with nearby well casings has been investigated thoroughly because corrosion of this kind is more serious than the anodic type. The performance of PCP systems has been analyzed with respect to obtaining better protection‐current distribution along the protected well casing at reduced anode current, together with reduced stray current (corrosion) at any nearby unprotected structure(s).

For uncoated well casings, protection current pulses are attenuated significantly and are smoothed out to be pure direct current after about 10 percent of the well‐casing buried length. High‐magnitude stray current can be found affecting any switched‐off well casings and hence they can be corroded faster from the top part than unprotected/remote wells, as are deeper well casings that may sustain considerable localized corrosion attack on the upper portions of the casing. Without the formation of a natural protective coating with high resistivity, the PCP system becomes malfunctioning, i.e. its performance becomes very similar to that of the conventional cathodic protection (CP) systems. This effect has been confirmed by field measurements in Oman, where magnesium hydroxide is minimally formed (in desert areas).

In reality, some of the PCP modules at the same station can have a slight deviation in the operating frequency and/or voltage. It is planned, therefore, that the investigation will be extended to simulate such cases and take into account the effect of multi‐layer soils.

Knowing the performance of PCP systems for protecting deep well casings is a critical issue for the oil industry.

The paper provides a sound basis on which oil producers can take decisions about the future application of the PCP systems, optimize their performance, and introduce application restrictions by studying all factors that affect PCP performance. The effectiveness of PCP in desert (sandy/rocky) soil, where calcium‐carbonate deposition predominates over magnesium‐hydroxide formation, has proven to be very similar to that of a conventional CP system. The reliability of artificial oil‐lifting systems will be increased by reducing oil production losses (“oil deferment”) and the rig mobilization, which has very high rent cost.

This paper aims to investigate an efficient approach to model the electromagnetic behaviors and predict stray-field loss inside the magnetic steel plate under 3D harmonic magnetization conditions so as to effectively prevent the structural components from local overheating and insulation damage in electromagnetic devices.

An experimental setup is applied to measure all the magnetic properties of magnetic steel plate under harmonic excitations with different frequencies and phase angles. The measurement and numerical simulation are carried out based on the updated TEAM Problem 21 Model B+ (P210-B+), under the 3D harmonic magnetization conditions. An improved method to evaluate the stray-field loss is proposed, and harmonic flux distribution in the structural components is analyzed.

The influence of the harmonic order and phase angle on the stray-field loss in magnetic steel components are noteworthy. Based on the engineering-oriented benchmark models, the variations of stray-field losses and magnetic field distribution inside the magnetic components under harmonic magnetization conditions are presented and analyzed in detail.

The capacity of the multi-function harmonic source, used in this work, was not large enough, which limits the magnetization level. Up to now, further improvements to increase the harmonic source capacity and investigations of the electromagnetic behaviors of magnetic steel components under multi-harmonic and DC-AC hybrid excitations are in progress.

To accurately predict the stray-field loss in magnetic steel plate, the improved method based on the combination of magnetic measurement and numerical simulation is proposed. The effects of the frequency and phase angle on the stray-field loss are analyzed.