Search results

This paper aims to estimate contact location from sparse and high-dimensional soft tactile array sensor data using the tactile image. The authors used three feature extraction methods: handcrafted features, convolutional features and autoencoder features. Subsequently, these features were mapped to contact locations through a contact location regression network. Finally, the network performance was evaluated using spherical fittings of three different radii to further determine the optimal feature extraction method.

This paper aims to estimate contact location from sparse and high-dimensional soft tactile array sensor data using the tactile image.

This research indicates that data collected by probes can be used for contact localization. Introducing a batch normalization layer after the feature extraction stage significantly enhances the model’s generalization performance. Through qualitative and quantitative analyses, the authors conclude that convolutional methods can more accurately estimate contact locations.

The paper provides both qualitative and quantitative analyses of the performance of three contact localization methods across different datasets. To address the challenge of obtaining accurate contact locations in quantitative analysis, an indirect measurement metric is proposed.

Human-induced marine environmental noise, such as commercial shipping and seismic exploration, is concentrated in the low-frequency range. Meanwhile, low-frequency sound signals can achieve long-distance propagation in water. To meet the requirements of long-distance underwater detection and communication, this paper aims to propose an micro-electro-mechanical system (MEMS) flexible conformal hydrophone for low-frequency underwater acoustic signals. The substrate of the proposed hydrophone is polyimide, with silicon as the piezoresistive unit.

This paper proposes a MEMS heterojunction integration process for preparing flexible conformal hydrophones. In addition, sensors prepared based on this process are non-contact flexible sensors that can detect weak signals or small deformations.

The experimental results indicate that making devices with this process cannot only achieve heterogeneous integration of silicon film, metal wire and polyimide, but also allow for customized positions of the silicon film as needed. The success rate of silicon film transfer printing is over 95%. When a stress of 1 Pa is applied on the x-axis or y-axis, the maximum stress on Si as a pie-zoresistive material is above, and the average stress on the Si film is around.

The flexible conformal vector hydrophone prepared by heterogeneous integration technology provides ideas for underwater acoustic communication and signal acquisition of biomimetic flexible robotic fish.

The growing awareness of climate risks associated with food safety issues has drawn the attention of stakeholders urging the food industry to carry out a sustainable food safety management system (FSMS). This study aims to investigate whether the critical success factors (CSFs) of sustainable FSMS can contribute to achieving climate neutrality, and how the adoption of FSMS 4.0 supported by the Industry Revolution 4.0 (IR 4.0) technologies moderates the impact of the CSFs on achieving climate neutrality.

Survey data from 255 food production firms in China and Vietnam were utilised for the empirical analysis. The research hypotheses were examined using structural equations modelling (SEM) with route analysis and bootstrapping techniques.

The results show that top management support, human resource management, infrastructure and integration appear as the significant CSFs that directly impact food production firms in achieving climate neutrality. Moreover, the results demonstrate that the adoption of FSMS 4.0 integrated with the three components (ecosystems, quality standards and robustness) significantly moderates the impact of the CSFs on achieving climate neutrality with lower inputs in human resources, infrastructure investment, integration and external assistance, and higher inputs in strengthening food safety administration.

This study provides empirical findings that fill the research gap in understanding the relationship between climate neutrality and the CSFs of sustainable FSMS while considering the moderating effects of the FSMS 4.0 components. The results provide theoretical and practical insights into how the food production sector can utilise IR 4.0 to attain sustainable FSMS for achieving climate neutrality.

This study aims to investigate the noise-inducing characteristics during the start-up process of a mixed-flow pump and the impact of different start-up schemes on pump noise.

This study conducted numerical simulations on the mixed-flow pump under different start-up schemes and investigated the flow characteristics and noise distribution under these schemes.

The results reveal that the dipole noise is mainly caused by pressure fluctuations, while the quadrupole noise is mainly generated by the generation, development and breakdown of vortices. Additionally, the noise evolution characteristics during the start-up process of the mixed-flow pump can be divided into the initial stage, stable growth stage, impulse stage and stable operation stage.

The findings of this study can provide a theoretical basis for the selection of start-up schemes for mixed-flow pumps, reducing flow noise and improving the operational stability of mixed-flow pumps.

The development of new advanced materials, such as photopolymerizable resins for use in stereolithography (SLA) and Ti6Al4V manufacture via selective laser melting (SLM) processes, have gained significant attention in recent years. Their accuracy, multi-material capability and application in novel fields, such as implantology, biomedical, aviation and energy industries, underscore the growing importance of these materials. The purpose of this study is oriented toward the application of new advanced materials in stent manufacturing realized by 3D printing technologies.

The methodology for designing personalized medical devices, implies computed tomography (CT) or magnetic resonance (MR) techniques. By realizing segmentation, reverse engineering and deriving a 3D model of a blood vessel, a subsequent stent design is achieved. The tessellation process and 3D printing methods can then be used to produce these parts. In this context, the SLA technology, in close correlation with the new types of developed resins, has brought significant evolution, as demonstrated through the analyses that are realized in the research presented in this study. This study undertakes a comprehensive approach, establishing experimentally the characteristics of two new types of photopolymerizable resins (both undoped and doped with micro-ceramic powders), remarking their great accuracy for 3D modeling in die-casting techniques, especially in the production process of customized stents.

A series of analyses were conducted, including scanning electron microscopy, energy-dispersive X-ray spectroscopy, mapping and roughness tests. Additionally, the structural integrity and molecular bonding of these resins were assessed by Fourier-transform infrared spectroscopy–attenuated total reflectance analysis. The research also explored the possibilities of using metallic alloys for producing the stents, comparing the direct manufacturing methods of stents’ struts by SLM technology using Ti6Al4V with stent models made from photopolymerizable resins using SLA. Furthermore, computer-aided engineering (CAE) simulations for two different stent struts were carried out, providing insights into the potential of using these materials and methods for realizing the production of stents.

This study covers advancements in materials and additive manufacturing methods but also approaches the use of CAE analysis, introducing in this way novel elements to the domain of customized stent manufacturing. The emerging applications of these resins, along with metallic alloys and 3D printing technologies, have brought significant contributions to the biomedical domain, as emphasized in this study. This study concludes by highlighting the current challenges and future research directions in the use of photopolymerizable resins and biocompatible metallic alloys, while also emphasizing the integration of artificial intelligence in the design process of customized stents by taking into consideration the 3D printing technologies that are used for producing these stents.

One of the challenges encountered in the design of guided projectiles is their prohibitive cost. To diminish it, an appropriate avenue many researchers have explored is the use of the non-actuator method for guiding the projectile to the target. In this method, biologically inspired by the flying concept of the single-winged seed, for instance, that of maple and ash trees, the projectile undergoes a helical motion to scan the region and meet the target in the descent phase. Indeed, the projectile is a decelerator device based on the autorotation flight while it attempts to resemble the seed’s motion using two wings of different spans. There exists a wealth of studies on the stability of the decelerators (e.g. the mono-wing, samara and pararotor), but all of them have assumed the body (exclusive of the wing) to be symmetric and paid no particular attention to the scanning quality of the region. In practice, however, the non-actuator-guided projectiles are asymmetric owing to the presence of detection sensors. This paper aims to present an analytical solution for stability analysis of asymmetric decelerators and apprise the effects of design parameters to improve the scanning quality.

The approach of this study is to develop a theoretical model consisting of Euler equations and apply a set of non-dimensionalized equations to reduce the number of involved parameters. The obtained governing equations are readily applicable to other decelerator devices, such as the mono-wing, samara and pararotor.

The results show that the stability of the body can be preserved under certain conditions. Moreover, pertinent conclusions are outlined on the sensitivity of flight behavior to the variation of design parameters.

The analytical solution and sensitivity analysis presented here can efficiently reduce the design cost of the asymmetric decelerator.

In response to the issue of traditional algorithms often falling into local minima or failing to find feasible solutions in manipulator path planning. The purpose of this paper is to propose a 3D artificial moment method (3D-AMM) for obstacle avoidance for the robotic arm's end-effector.

A new method for constructing temporary attractive points in 3D has been introduced using the vector triple product approach, which generates the attractive moments that attract the end-effector to move toward it. Second, distance weight factorization and spatial projection methods are introduced to improve the solution of repulsive moments in multiobstacle scenarios. Third, a novel motion vector-solving mechanism is proposed to provide nonzero velocity for the end-effector to solve the problem of limiting the solution of the motion vector to a fixed coordinate plane due to dimensionality constraints.

A comparative analysis was conducted between the proposed algorithm and the existing methods, the improved artificial potential field method and the rapidly-random tree method under identical simulation conditions. The results indicate that the 3D-AMM method successfully plans paths with smoother trajectories and reduces the path length by 20.03% to 36.9%. Additionally, the experimental comparison outcomes affirm the feasibility and effectiveness of this method for obstacle avoidance in industrial scenarios.

This paper proposes a 3D-AMM algorithm for manipulator path planning in Cartesian space with multiple obstacles. This method effectively solves the problem of the artificial potential field method easily falling into local minimum points and the low path planning success rate of the rapidly-exploring random tree method.