Search results

Because of the anisotropy of the process and the variability in the quality of printed parts, finite element analysis is not directly applicable to recycled materials manufactured using fused filament fabrication. The purpose of this study is to investigate the numerical-experimental mechanical behavior modeling of the recycled polymer, that is, recyclable polyethylene terephthalate (rPET), manufactured by a deposition FFF process under compressive stresses for new sustainable designs.

In all, 42 test specimens were manufactured and analyzed according to the ASTM D695-15 standards. Eight numerical analyzes were performed on a real design manufactured with rPET using Young's compression modulus from the experimental tests. Finally, eight additional experimental tests under uniaxial compression loads were performed on the real sustainable design for validating its mechanical behavior versus computational numerical tests.

As a result of the experimental tests, rPET behaves linearly until it reaches the elastic limit, along each manufacturing axis. The results of this study confirmed the design's structural safety by the load scenario and operating boundary conditions. Experimental and numerical results show a difference of 0.001–0.024 mm, allowing for the rPET to be configured as isotropic in numerical simulation software without having to modify its material modeling equations.

The results obtained are of great help to industry, designers and researchers because they validate the use of recycled rPET for the ecological production of real-sustainable products using MEX technology under compressive stress and its configuration for numerical simulations. Major design companies are now using recycled plastic materials in their high-end designs.

Validation results have been presented on test specimens and real items, comparing experimental material configuration values with numerical results. Specifically, to the best of the authors’ knowledge, no industrial or scientific work has been conducted with rPET subjected to uniaxial compression loads for characterizing experimentally and numerically the material using these results for validating a real case of a sustainable industrial product.

Fiber reinforced additive manufacturing (FRAM) is an emerging technology that combines additive manufacturing and composite materials. As a result, design freedom offered by the manufacturing process can be leveraged in design optimization. The purpose of the study is to propose a novel method that improves structural performance by optimizing 3D print orientation of FRAM components.

This work proposes a two-part design optimization method that optimizes 3D global print orientation and topology of a component to improve a structural objective function. The method considers two classes of design variables: (1) print orientation design variables and (2) density-based topology design variables. Print orientation design variables determine a unique 3D print orientation to influence anisotropic material properties. Topology optimization determines an optimal distribution of material within the optimized print orientation.

Two academic examples are used to demonstrate basic behavior of the method in tension and shear. Print orientation and sequential topology optimization improve structural compliance by 90% and 58%, respectively. An industry-level example, an aerospace component, is optimized. The proposed method is used to achieve an 11% and 15% reduction of structural compliance compared to alternative FRAM designs. In addition, compliance is reduced by 43% compared to an equal-mass aluminum design.

Current research surrounding FRAM focuses on the manufacturing process and neglects opportunities to leverage design freedom provided by FRAM. Previous FRAM optimization methods only optimize fiber orientation within a 2D plane and do not establish an optimized 3D print orientation, neglecting exploration of the entire orientation design space.

The primary objective of this study is characterizing the anisotropic mechanical properties of corrugated cardboard and simultaneously simulating its drop cushioning dynamic effects under various drop conditions.

Static and dynamic tests were conducted on corrugated cardboard to obtain adequate experimental data in different directions. An effective anisotropic constitutive model is introduced by developing the honeycomb materials model in ANSYS LS-Dyna, and an effective approach is established toward effectively determining the material parameters from the test data obtained. The model is validated by comparing simulation results with experimental data from five drop conditions, including bottom drop, front drop, side drop, 30° side drop and edge drop. Additionally, simulations are conducted to study the cushioning performance of the packaging by dropping the corrugated cardboard at different heights.

The study establishes a fast and effective approach to simulating the drop cushioning performance of corrugated cardboard under various drop conditions, which demonstrates good agreement with experimental data.

This approach is of value for packaging protection and provides guidance for stacking of packaging during transportation.

The purpose of this paper is to apply the concept of equivalent initial flaw size (EIFS) to the anisotropic nickel-based single crystal (SX) material, and to predict the fatigue life on this basis. The crack propagation law of SX material at different temperatures and the weak correlation of EIFS values verification under different loading conditions are also investigated.

A three-parameter time to crack initial (TTCI) method with multiple reference crack lengths under different loading conditions is established, which include the TTCI backstepping method and EIFS fitting method. Subsequently, the optimized EIFS distribution is obtained based on the random crack propagation rate and maximum likelihood estimation of median fatigue life. Then, an effective driving force based on anisotropic and mixed crack propagation mode is proposed to describe the crack propagation rate in the small crack stage. Finally, the fatigue life of three different temperature ESE(T) standard specimens is predicted based on the EIFS values under different survival rates.

The optimized EIFS distribution based on EIFS fitting - maximum likelihood estimation (MLE) method has the highest accuracy in predicting the total fatigue life, with the range of EIFS values being about [0.0028, 0.0875] (mm), and the mean value of EIFS being 0.0506 mm. The error between the predicted fatigue life based on the crack propagation rate and EIFS distribution for survival rates ranges from 5% to 95% and the experimental life is within two times dispersion band.

This paper systematically proposes a new anisotropic material EIFS prediction method, establishing a framework for predicting the fatigue life of SX material at different temperatures using fracture mechanics to avoid inaccurate anisotropic constitutive models and fatigue damage accumulation theory.

The purpose of this research is present an experimental and numerical study of the mechanical properties of the acrylonitrile butadiene styrene (ABS) in the additive manufacturing (AM) by fused filament fabrication (FFF). The characterization and mechanical models obtained are used to predict the elastic behavior of a prosthetic foot and the failure of a prosthetic knee manufactured with FFF.

Tension tests were carried out and the elastic modulus, yield stress and tensile strength were evaluated for different material directions. The material elastic constants were determined and the influence of infill density in the mechanical strength was evaluated. Yield surfaces and failure criteria were generated from the tests. Failures over prosthetic elements in tridimensional stresses were analyzed; the cases were evaluated via finite element method.

The experimental results show that the material is transversely isotropic. The elasticity modulus, yield stress and ultimate tensile strength vary linearly with the infill density. The stresses and the failure criteria were computed and compared with the experimental tests with good agreement.

This research can be applied to predict failures and improve reliability in FFF or fused deposition modeling (FDM) products for applications in high-performance industries such as aerospace, automotive and medical.

This research aims to promote its widespread adoption in the industrial and medical sectors by increasing reliability in products manufactured with AM based on the failure criterion.

Most of the models studied apply to plane stress situations and standardized specimens of printed material. However, the models applied in this study can be used for functional parts and three-dimensional stress, with accuracy in the range of that obtained by other researchers. The researchers also proposed a method for the mechanical study of fragile materials fabricated by processes of FFF and FDM.

This paper aims to provide SIF calculation method for engineering application.

In this paper, the stress intensity factors (SIFs) calculation method is applied to the anisotropic Ni-based single crystal film cooling holes (FCHs) structure.

Based on contour integral, the anisotropic SIFs analysis finite element method (FEM) in Ni-based single crystal is proposed. The applicability and mesh independence of the method is assessed by comparing the calculated SIFs using mode of plate with an edge crack. Anisotropic SIFs can be calculated with excellent accuracy using the finite element contour integral approach. Then, the effect of crystal orientation and FCHs interference on the anisotropic SIFs is clarified. The SIFs of FCH edge crack in the [011] orientated Ni-based single crystal increases faster than the other two orientations. And the SIF of horizontal interference FCHs edge crack is also larger than that of the inclined interference one.

The SIFs of the FCH edge crack in the turbine air-cooled blade are innovatively computed using the sub-model method. Both the Mode I and II SIFs of FCHs edge crack in blade increase with crack growing.

This study aims to comprehensively investigate the mixed-mode fracture behavior and mechanical properties of selective laser sintering (SLS) polyamide 12 (PA12) components, considering different build orientations and layer thicknesses. The primary objectives include the following. Conducting mixed-mode fracture and mechanical analyses on SLS PA12 parts. Investigating the influence of build orientation and layer thickness on the mechanical properties of SLS-printed components. Examining the fracture mechanisms of SLS-produced Arcan fracture and tensile specimens through experimental methods and finite element analyses.

The research used a combination of experimental techniques and numerical analyses. Tensile and Arcan fracture specimens were fabricated using the SLS process with varying build orientations (X, X–Y, Z) and layer thicknesses (0.1 mm, 0.2 mm). Mechanical properties, including tensile strength, modulus of elasticity and critical stress intensity factor, were quantified through experimental testing. Mixed-mode fracture tests were conducted using a specialized fixture, and finite element analyses using the J-integral method were performed to calculate fracture toughness. Scanning electron microscopy (SEM) was used for detailed morphological analysis of fractured surfaces.

The investigation revealed that the highest tensile properties were achieved in samples fabricated horizontally in the X orientation with a layer thickness of 0.1 mm. Additionally, parts manufactured with a layer thickness of 0.2 mm exhibited favorable mixed-mode fracture behavior. The results emphasize the significance of build orientation and layer thickness in influencing mechanical properties and fracture behavior. SEM analysis provided valuable insights into the failure mechanisms of SLS-produced PA12 components.

This study contributes to the field of additive manufacturing by providing a comprehensive analysis of the mixed-mode fracture behavior and mechanical properties of SLS-produced PA12 components. The investigation offers novel insights into the influence of build orientation and layer thickness on the performance of such components. The combination of experimental testing, numerical analyses and SEM morphological observations enhances the understanding of fracture behavior in additive manufacturing processes. The findings contribute to optimizing the design and manufacturing of high-quality PA12 components using SLS technology.

The purpose of this work is to optimize the monitoring of vibrations on dynamometric test rigs for railway brakes. This is a quite demanding application considering the continuous increase of performances of high-speed trains that involve higher testing specifications for brake pads and disks.

In this work, authors propose a mixed approach in which relatively simple finite element models are used to support the optimization of a diagnostic system that is used to monitor vibration levels and rotor-dynamical behavior of the machine. The model is calibrated with experimental data recorded on the same rig that must be identified and monitored. The whole process is optimized to not interfere with normal operations of the rig, using common inertial sensor and tools and are available as standard instrumentation for this kind of applications. So at the end all the calibration activities can be performed normally without interrupting the activities of the rig introducing additional costs due to system unavailability.

Proposed approach was able to identify in a very simple and fast way the vibrational behavior of the investigated rig, also giving precious information concerning the anisotropic behavior of supports and their damping. All these data are quite difficult to be found in technical literature because they are quite sensitive to assembly tolerances and to many other factors. Dynamometric test rigs are an important application widely diffused for both road and rail vehicles. Also proposed procedure can be easily extended and generalized to a wide value of machine with horizontal rotors.

Most of the studies in literature are referred to electrical motors or turbomachines operating with relatively slow transients and constant inertial properties. For investigated machines both these conditions are not verified, making the proposed application quite unusual and original with respect to current application. At the same time, there is a wide variety of special machines that are usually marginally covered by standard testing methodologies to which the proposed approach can be successfully extended.

The purpose of this study is to investigate how the amount of material used and printing parameters affect the mechanical and water sorption properties of acrylonitrile butadiene styrene printed parts.

The specimens were printed using different printing parameters such as shell number, infill pattern and printing orientation, while accounting for the amount of material used. The mechanical properties of the printed parts were then evaluated using tensile, compression and flexural tests, along with sorption tests.

The results revealed that the maximum tensile stress of 31.41 MPa was obtained when using 100% infill and a horizontal printing orientation. Similarly, the maximum flexural strength and compression of 40.5 MPa and 100.7 MPa, respectively, were obtained with 100% infill. The printing orientation was found to have a greater impact on mechanical behavior compared to the number of shells or infill patterns. Specifically, the horizontal printing orientation resulted in specimens with at least 25% greater strength compared to the vertical printing orientation. Furthermore, the relationship between the amount of material used and strength was evident in the tensile and flexural tests, which showed a close correlation between the two.

This study’s originality lies in its focus on optimizing the amount of material used to achieve the best strength-to-mass ratio and negligible water infiltration. The findings showed that specimens with two shells and a 60% infill density exhibited the best strength-to-mass ratio.

This paper aims to investigate the impact of combining grain-oriented electrical steel (GOES) grades on specific iron losses and the flux density distribution within a single-phase magnetic core.

This paper presents the results of finite-element method (FEM) simulations investigating the impact of mixing two different GOES grades on losses of a single-phase magnetic core. The authors used different models: a 3D model with a highly detailed geometry including both saturation and anisotropy, as well as a simplified 2D model to save computation time. The behavior of the flux distribution in the mixed magnetic core is analyzed. Finally, the results from the numerical simulations are compared with experimental results.

The specific iron losses of a mixed magnetic core exhibit a nonlinear decrease with respect to the GOES grade with the lowest losses. Analyzing the magnetic core behavior using 2D and 3D FEM shows that the rolling direction of the GOES grades plays a critical role on the nonlinearity variation of the specific losses.

The novelty of this research lies in achieving an optimum trade-off between the manufacturing cost and the core efficiency by combining conventional and high-performance GOES grade in a single-phase magnetic core.