Search results

There are a number of different approaches for calculating creep-fatigue (CF) damage for design, such as the French nuclear code RCC-MRx, the American ASME III NH and the British R5 assessment code. To acquire estimates for the CF damage, that are not overly conservative, both the cyclic material softening/hardening and the potential changes in relaxation behavior have to be considered. The data presented here and models are an initial glimpse of the ongoing European FP7 project MATISSE effort to model the softening and relaxation behavior of Grade 91 steel under CF loading. The resulting models are used for calculating the relaxed stress at arbitrary location in the material cyclic softening curve. The initial test results show that softening of the material is not always detrimental. The initial model development and the pre-assessment of the MATISSE data show that the relaxed stress can be robustly predicted with hold time, strain range and the cyclic life fraction as the main input parameters. The paper aims to discuss these issues.

Engineering models have been developed for predicting cyclic softening and relaxation for Gr. 91 steel at 550 and 600°C.

A simple engineering model can adequately predict the low cycle fatigue (LCF) and CF softening rates of Gr. 91 steel. Also a simple relaxation model was successfully defined for predicting relaxed stress of both virgin and cyclically softened material.

The data are not yet complete and the models will be updated when the complete set of data in the MATISSE project is available.

The models described can be used for predicting P91 material softening in an arbitrary location (n/N_f0) of the LCF and CF cyclic life. Also the relaxed stress in the softened material can be estimated.

The models are simple in nature but are able to estimate both material softening and relaxation in arbitrary location of the softening curve. This is the first time the Wilshire methodology has been applied on cyclic relaxation data.

The purpose of this paper is to develop a method suitable for the design of reinforced concrete columns subjected to a standard fire.

The Zone Method – a ’simplified calculation method” included in Eurocode 2 – has been developed by Hertz as a manual calculation scheme for the check of fire resistance of concrete sections. The basic idea is to disregard the thermal strains and to calculate the resistance of a cross-section by reducing the concrete cross-section by a “damaged zone”. It is assumed that all fibers can reach their ultimate, temperature dependent strength. Therefore, it is a plastic concept; the information on the state of strain is lost. The calculation of curvatures and deflections is thus only possible by making further assumptions. Extensions of the zone method toward a general calculation method, suitable for the implementation in commercial design software and using the temperature dependent stress–strain curves of the Advanced Calculation Method, have been developed in Germany. The extension by Cyllok and Achenbach is presented in detail. The necessary assumptions of the Zone Method are reviewed, and an improved proposal for the consideration of the reinforcement in this extended Zone Method is presented.

The principles and assumptions of the Zone Method proposed by Hertz can be validated.

An extension of the Zone Method suitable for the implementation in design software is proposed.

Large displacement misalignment under the action of active faults can cause complex three-dimensional deformation in subway tunnels, resulting in severe damage, distortion and misalignment. There is no developed system of fortification and related codes to follow. There are scientific problems and technical challenges in this field that have never been encountered in past research and practices.

This paper adopted a self-designed large-scale active fault dislocation simulation loading system to conduct a similar model test of the tunnel under active fault dislocation based on the open-cut tunnel project of the Urumqi Rail Transit Line 2, which passes through the Jiujiawan normal fault. The test simulated the subway tunnel passing through the normal fault, which is inclined at 60°. This research compared and analyzed the differences in mechanical behavior between two types of lining section: the open-cut double-line box tunnel and the modified double-line box arch tunnel. The structural response and failure characteristics of the open-cut segmented lining of the tunnel under the stick-slip part of the normal fault were studied.

The results indicated that the double-line box arch tunnel improved the shear and longitudinal bending performance. Longitudinal cracks were mainly distributed in the baseplate, wall foot and arch foot, and the crack position was basically consistent with the longitudinal distribution of surrounding rock pressure. This indicated that the longitudinal cracks were due to the large local load of the cross-section of the structure, leading to an excessive local bending moment of the structure, which resulted in large eccentric failure of the lining and formation of longitudinal cracks. Compared with the ordinary box section tunnel, the improved double-line box arch tunnel significantly reduced the destroyed and damage areas of the hanging wall and footwall. The damage area and crack length were reduced by 39 and 59.3%, respectively. This indicates that the improved double-line box arch tunnel had good anti-sliding performance.

This paper adopted a self-designed large-scale active fault dislocation simulation loading system to conduct a similar model test of the tunnel under active fault dislocation. This system increased the similarity ratio of the test model, improved the dislocation loading rate and optimized the simulation scheme of the segmented flexible lining and other key factors affecting the test. It is of great scientific significance and engineering value to investigate the structure of subway tunnels under active fault misalignment, to study its force characteristics and damage modes, and to provide a technical reserve for the design and construction of subway tunnels through active faults.

Women leaders operate within multiple roles, managing both work and nonwork obligations. Exploring work-life balance constructs, this study examined role integration, social support sources, and work-family conflict to determine their influence on women leaders. Findings suggested that women leaders felt the benefit of a variety of social support services, but especially from sources external to the organization. Women leaders were diverse in role integration strategies, with respondents largely divided between blurring and segregating their work and nonwork roles. Time-based work-family conflict was slightly more apparent than strain-based conflict. Women leaders also indicated that their work interfered with their family more than their family interfered with their work. Findings provide valuable insights as to how women view work-life balance within their roles as leaders.

This method will become a new development trend in subgrade structure design for high speed railways.

This paper summarizes the structural types and design methods of subgrade bed for high speed railways in China, Japan, France, Germany, the United States and other countries based on the study and analysis of existing literature and combined with the research results and practices of high speed railway subgrade engineering at home and abroad.

It is found that in foreign countries, the layered reinforced structure is generally adopted for the subgrade bed of high speed railways, and the unified double-layer or multi-layer structure is adopted for the surface layer of subgrade bed, while the simple structure is adopted in China; in foreign countries, different inspection parameters are adopted to evaluate the compaction state of fillers according to their respective understanding and practice, while in China, compaction coefficient, subsoil coefficient and dynamic deformation modulus are adopted for such evaluation; in foreign countries, the subgrade top deformation control method, the subgrade bottom deformation control method, the subsurface fill strength control method are mainly adopted in subgrade bed structure design of high speed railways, while in China, dynamic deformation control of subgrade surface and dynamic strain control of subgrade bed bottom layer is adopted in the design. However, the cumulative deformation of subgrade caused by train cyclic vibration load is not considered in the existing design methods.

This paper introduces a new subgrade structure design method based on whole-process dynamics analysis that meets subgrade functional requirements and is established on the basis of the existing research at home and abroad on prediction methods for cumulative deformation of subgrade soil.