Search results

The purpose of this paper is to investigate the surface integrity features, including surface roughness (SR), recast layer (RL), material migration, topography and wire wear pattern in rough and trim-cut wire electric discharge machine (WEDM) of hybrid composite (Al6061-90%/SiC-2.5%/TiB₂-7.5%).

Effects of four important factors, namely, rough-cut history (RCH), pulse on time (T_on), peak current (IP) and wire offset (WO) have been assessed on the responses of interest for trim-cut WEDM. Box–Behnken design (RSM) was used to formulate the experimentation plan. Quantitative indices of surface integrity, namely, SR and RL, and selected samples have been investigated for qualitative analysis, namely, surface topography, material migration and wire wear pattern.

T_on and IP are found to be most significant, whereas RCH and WO are found insignificant for SR. T_on and WO were found to be the most significant factors affecting RL. After trim cut, an RL of thickness 8.26 µm is observed if the initial rough cut has been accomplished at high discharge energy setting. Whereas the best value of RL thickness, i.e. 5.36 µm, can be realized with low level of RCH. A significant decrease in the presence of foreign materials is recorded, indicating its strong correlation with the discharge energy used during machining.

Investigation on surface integrity features for machining of hybrid composite through rough and trim-cut WEDM has been reported by only a limited number of researchers in the past. This study is attempted at fulfilling few vital gaps by addressing the issues such as evaluation of the efficacy of trim cutting under different discharge energy conditions (using RCH), analysis of wire wear pattern in both rough and trim-cut modes and investigation of the wire breakage phenomenon during machining.

The purpose of this paper is to study the correlation between the thicknesses of the C–Ni films that have been prepared by RF-magnetron sputtering on quartz substrates and their three-dimensional (3D) micro morphology. In this work by AFM images, this paper studied stereo metric analysis of these films.

The C–Ni films have been prepared by RF-magnetron sputtering on quartz substrates using a mosaic target consisting of pure graphite and strips of pure nickel approximately 2 cm² attached to the graphite race track. The field emission scanning electronic microscopy (FESEM) images were used for the morphological characterization.

The histogram peaks are zero for all samples and the histograms are almost symmetric around zero. Temperature did not have much effect on the degree of isolation, so all four diagrams have similar results. The qualitative observations through statistical parameters of the 3D surface texture revealed that the smoothest surface has been obtained for C-Ni films annealed at 500 °C (Sa, Sq, Sz and Sv have the lower values), while the most irregular topography has been found for C-Ni films annealed at 300 °C (the fractal dimension D = 2.01 ± 0.131).

As shown in FESEM images, the size of the particles was increased for films deposited from 300 ºC to 800ºC; however, at 1000ºC, it decreased significantly. The histogram peaks are zero for all samples and the histograms were almost symmetric around zero. Also, the largest and lowest root mean heights (Sq) belong to films at 300 °C and 500 °C. Furthermore, the more irregular surface was found at 300 °C, and the more regular surface was found at 500 °C. As the temperature was increased to 800 °C, the values of the IAPSD function increased systematically, and then the values of the IAPSD function was decreased in the fourth sample. The surface skewness of samples annealed at 1000 °C was positive which confirms the lack of dominance of cavities on their surface with the highest amount of C-Ni films at 800 °C.

This paper aims to characterize the surface film formed on Alloys 800 and 690 in chloride and thiosulfate-containing solution at 300°C.

Alloy 800 and 690 were immersed in chloride and thiosulfate-containing solution at 300°C up to five days, and then the surface film was analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and energy dispersive X-ray spectrometers (EDX).

Through static immersion experiments in a high-temperature and high-pressure water environment, the alloy samples covered by surface film after five days of immersion were obtained. The morphology of the surface film was characterized at both horizontal and cross-sectional scales using SEM and focused ion beam-TEM techniques. It was observed that due to the influence of the quartz lining, the surface film primarily exhibited a bilayered structure. The first layer contained a significant amount of SiO₂, with a higher content of metal hydroxides compared to metal oxides. The second layer was predominantly composed of Fe, Ni and Cr, with a higher content of metal oxides compared to metal hydroxides.

The results showed that the materials of the lining of the autoclave could significantly influence the film composition of the tested material, which should be paid attention when analyzing the corrosion mechanism at high temperature.

This study critically examines the safety aspects of ablution spaces in United Arab Emirates (UAE) mosques, emphasising the evaluation of smooth ceramic tile floorings prone to water accumulation. As an integral practice in Islamic worship, ablution spaces cater to a diverse demographic, making their safety a paramount concern. This study aims to meticulously assess slip-resistance properties and surface characteristics to provide practical recommendations for enhanced safety measures.

The investigation involves in situ measurements of traction properties and an extensive analysis of surface features in thirty mosques across the UAE. This comprehensive approach allows for identifying the unique challenges posed by ceramic tile floorings in ablution spaces. The study uses a portable tribometer for dynamic friction coefficient measurements, ensuring accurate slip-resistance evaluations. Surface texture analysis uses a portable profilometer to quantify roughness parameters.

The study’s findings significantly advance the comprehension of safety considerations in ablution spaces. Through empirical evidence and evidence-based insights, the research identifies immediate safety concerns and provides practical recommendations to create secure and inclusive environments within mosques. The emphasis lies on safeguarding the well-being of worshippers and contributing to the broader goal of safety in religious spaces.

The original contribution of this study lies in its dual focus on immediate safety concerns and the deeper understanding of unique safety challenges within ablution spaces. By offering evidence-based insights and practical recommendations, the research strives to make meaningful contributions to creating secure and inclusive environments within mosques.

The importance of the agri-food supply chain in both food production and distribution has made the issue of its development a critical concern. Based on configuration theory and congruence theory, this research investigates the complex impact of supply chain concentration on financial growth in agri-food supply chains.

The cluster analysis and response surface methodology are employed to analyse the data collected from 207 Chinese agri-food companies from 2010 to 2022.

The results indicate that different combination patterns of supply chain concentration can lead to different levels of financial growth. We discover that congruent supplier and customer concentration is beneficial for companies’ financial growth. This impact is more pronounced when the company is in the agricultural production stage of agri-food supply chains. Post-hoc analysis indicates that there exists an inverted U-shaped relationship between the overall levels of supply chain concentration and financial growth.

Our research uncovers the complex interplay between supply chain base and financial outcomes, thereby revealing significant ramifications for agri-food supply chain managers to optimise their strategies for exceptional financial growth.

This study proposes a combined approach of cluster analysis and response surface analysis for analysing configuration issues in supply chain management.

This paper aims to study the tribological characteristics of the electrical contact system under different displacement amplitudes.

First, the risk frequency of real nuclear safety distributed control system (DCS) equipment is evaluated. Subsequently, a reciprocating friction test device which is characterized by a ball-on-flat configuration is established, and a series of current-carrying tribological tests are carried out at this risk frequency.

At risk frequency and larger displacement amplitude, the friction coefficient visibly rises. The reliability of the electrical contact system declines as amplitude increases. The wear morphology analysis shows that the wear rate increases significantly and the degree of interface wear intensifies at a larger amplitude. The wear area occupied by the third body layer increases sharply, and the appearance of plateaus on the surface leads to the increase of friction coefficient and contact resistance. EDS analysis suggests that oxygen elements progressively arise in the third layer as a result of increased air exposure brought on by larger displacement amplitude.

Results are significant for recognizing the tribological properties of electrical connectors in nuclear power control systems.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2024-0098/

Aluminum alloy is considered an ideal material in aerospace, automobile and other fields because of its lightweight, high specific strength and easy processing. However, low hardness and strength of the surface of aluminum alloys are the main factors that limit their applications. The purpose of this study is to obtain a composite coating with high hardness and lubricating properties by applying GO–PVA over MAO coating.

A pulsed bipolar power supply was used as power supply to prepare the micro-arc oxidation (MAO) coating on 6061 aluminum sample. Then a graphene oxide-polyvinyl alcohol (GO–PVA) composite coating was prepared on MAO coating for subsequent experiments. Samples were characterized by Fourier infrared spectroscopy, X-ray diffraction, Raman spectroscopy and thermogravimetric analysis. The friction test is carried out by the relative movement of the copper ball and the aluminum disk on the friction tester.

Results showed that the friction coefficient of MAO samples was reduced by 80% after treated with GO–PVA composite film.

This research has made a certain contribution to the surface hardness and tribological issues involved in the lightweight design of aluminum alloys.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-12-2023-0427/

The use of additive manufacturing in many branches of industry is increasing significantly because of its many advantages, such as being able to produce complex parts that cannot be produced by classical methods, using fewer materials, easing the supply chain with on-site production, being able to produce with all kinds of materials and producing lighter parts. The binder jetting technique, one of the additive manufacturing methods researched within the scope of this work, is predicted to be the additive manufacturing method that will grow the most in the next decade, according to many economic reports. Although additive manufacturing methods have many advantages, they can be slower than classical manufacturing methods regarding production speed. For this reason, this study aims to increase the manufacturing speed in the binder jetting method.

Adaptive slicing and variable binder amount algorithm (VBAA) were used to increase manufacturing speed in binder jetting. Taguchi method was used to optimize the layer thickness and saturation ratio in VBAA. According to the Taguchi experimental design, 27 samples were produced in nine different conditions, three replicates each. The width of the samples in their raw form was measured. Afterward, the samples were sintered at 1,500 °C for 2 h. After sintering, surface roughness and density tests were performed. Therefore, the methods used have been proven to be successful. In addition, measurement possibilities with image processing were investigated to make surface roughness measurements more accessible and more economical.

As a result of the tests, the optimum printing condition was decided to be 180–250 µm for layer thickness and 50% for saturation. A separate test sample was then designed to implement adaptive slicing. This test sample was produced in three pieces: adaptive (180–250 µm), thin layer (180 µm) and thick layer (250 µm) with the determined parameters. The roughness values of the adaptive sliced sample and the thin layer sample were similar and better than the thick layer sample. A similar result was obtained using 12.31% fewer layers in the adaptive sample than in the thin layer sample.

The use of adaptive slicing in binder jetting has become more efficient. In this way, it will increase the use of adaptive slicing in binder jetting. In addition, a cheap and straightforward image processing method has been developed to calculate the surface roughness of the parts.

Physics-informed neural networks (PINNs) have become a new tendency in flow simulation, because of their self-advantage of integrating both physical and monitored information of fields in solving the Navier–Stokes equation and its variants. In view of the strengths of PINN, this study aims to investigate the impact of spatially embedded data distribution on the flow field results around the train in the crosswind environment reconstructed by PINN.

PINN can integrate data residuals with physical residuals into the loss function to train its parameters, allowing it to approximate the solution of the governing equations. In addition, with the aid of labelled training data, PINN can also incorporate the real site information of the flow field in model training. In light of this, the PINN model is adopted to reconstruct a two-dimensional time-averaged flow field around a train under crosswinds in the spatial domain with the aid of sparse flow field data, and the prediction results are compared with the reference results obtained from numerical modelling.

The prediction results from PINN results demonstrated a low discrepancy with those obtained from numerical simulations. The results of this study indicate that a threshold of the spatial embedded data density exists, in both the near wall and far wall areas on the train’s leeward side, as well as the near train surface area. In other words, a negative effect on the PINN reconstruction accuracy will emerge if the spatial embedded data density exceeds or slips below the threshold. Also, the optimum arrangement of the spatial embedded data in reconstructing the flow field of the train in crosswinds is obtained in this work.

In this work, a strategy of reconstructing the time-averaged flow field of the train under crosswind conditions is proposed based on the physics-informed data-driven method, which enhances the scope of neural network applications. In addition, for the flow field reconstruction, the effect of spatial embedded data arrangement in PINN is compared to improve its accuracy.

Wire-arc-based additive manufacturing (WAAM) is a promising technology for the efficient and economical fabrication of medium-large components. However, the anisotropic behavior of the multilayered WAAM-fabricated components remains a challenging problem.

The purpose of this paper is to conduct a comprehensive study of the grain morphology, crystallographic orientation and texture in three regions of the WAAM printed component. Furthermore, the interdependence of the grain morphology in different regions of the fabricated component with their mechanical and tribological properties was established.

The electron back-scattered diffraction analysis of the top and bottom regions revealed fine recrystallized grains, whereas the middle regions acquired columnar grains with an average size of approximately 8.980 µm. The analysis revealed a higher misorientation angle and an intense crystallographic texture in the upper and lower regions. The investigations found a higher microhardness value of 168.93 ± 1.71 HV with superior wear resistance in the bottom region. The quantitative evaluation of the residual stress detected higher compressive stress in the upper regions. Evidence for comparable ultimate tensile strength and greater elongation (%) compared to its wrought counterpart has been observed.

The study found a good correlation between the grain morphology in different regions of the WAAM-fabricated component and their mechanical and wear properties. The Hall–Petch relationship also established good agreement between the grain morphology and tensile test results. Improved ductility compared to its wrought counterpart was observed. The anisotropy exists with improved mechanical properties along the longitudinal direction. Moreover, cylindrical components have superior tribological properties compared with cuboidal components.