Search results

The aim of this paper is to provide a simple yet accurate and efficient geometric method for thermal homogenization of impregnated and non-impregnated coil winding technologies based on the concept of thermal resistance.

For regular windings, the periodic microscopic cell in the winding space is identified. Also, for irregular windings, the average microscopic cell of the winding is determined. An approximation is used to calculate the thermal resistance of the winding cell. Based on this approximation, the winding insulation is considered as a circular ring around the wire. Mathematical equations are obtained to calculate the equivalent thermal resistance of the cell. The equivalent thermal conductivity of the winding is calculated using equivalent thermal resistance of the cell. Winding thermal homogenization is completed by determining the equivalent thermal properties of the cell.

The thermal pattern of different windings is simulated and compared with the results of different homogenization methods. The results show that the proposed method is applicable for a wide range of windings in terms of winding scheme, packing factor and winding insulation. Also, the results show that the proposed method is more accurate than other winding homogenization methods in calculating the equivalent thermal conductivity of the winding.

In this paper, the change of electrical resistance of the winding with temperature and thermal contact between the sub-components are ignored. Also, liquid insulators, such as oils, and rectangular wires were not investigated. Research in these topics is considered as future work.

Unlike other homogenization methods, the proposed method can be applied to non-impregnated and irregular windings. Also, compared to other homogenization methods, the proposed method has a simpler formulation that makes it easier to program and implement. All of these indicate the efficiency of the proposed method in the thermal analysis of the winding.

This paper aims to design a walking-clamp mechanism for the inspection robot of transmission line. The focus for this design is on climbing ability and obstacle-crossing ability with a goal to create a novel walking-clamp mechanism that can clamp not only the line but also the obstacle.

A novel clamping jaw used in the walking-clamp mechanism is proposed. The clamping wheel is mounted on the lower end of clamping jaw to reduce the friction between the clamping jaw and the line, and the top end of clamping jaw is designed as a hook structure to clamp the obstacle. The working principle and force states of the walking-clamp mechanism clamping the line and obstacle are analyzed, and the simulation and prototype experiments are carried out.

The experimental results show that this mechanism can clamp the obstacle steadily, and the clamping forces of the front and back pairs of clamping jaws are almost equal during robot walking along the catenary-shaped line. It is in agreement with the theoretical analysis, and it demonstrates that this mechanism can meet the working requirements of inspection robot.

This novel mechanism can be used for inspection robot of transmission line, and it is beneficial for robot to complete long-distance inspection works.

It stands to reduce costs related to inspection and improve the inspection efficiency.

Innovative features include its structure, working principle and force states.

This paper aims to propose a method to reduce the resistance of silicon-based V-shaped electrothermal microactuator (VEM) by applying a surface sputtering process.

Four VEM’s samples have been fabricated using traditional silicon on insulator (SOI)-Micro-electro-mechanical System (MEMS) technology, three of them are coated with a thin layer of platinum on the top surface by sputtering technique with different sputtered times and the other is original. The displacements of the VEM are calculated and simulated to evaluate the advantages of sputtering method.

The measured results show that the average resistance of the sputtered structures is approximately 1.16, 1.55 and 2.4 times lower than the non-sputtering sample corresponding to the sputtering time of 1.5, 3 and 6 min. Simulation results confirmed that the maximum displacement of the sputtered VEM is almost 1.45 times larger than non-sputtering one in the range of voltage from 8 to 20 V. The experimental displacements are also measured to validate the better performance of the sputtered samples.

The experimental results demonstrated the better displacement of the VEM structure after using the platinum sputtering process. The improvement can be considered and applied for enhancing displacement as well as decreasing the driving voltage of the other electrothermal microactuators like U- or Z-shaped structures while combining with the low-cost SOI-MEMS micromachining technology.

In the process of continuous casting and rolling of steel plate, due to the influence of rolling equipment and process, there are scratches, inclusions, patches, scabs and pitted surfaces on the surface of steel plate, which will not only affect the corrosion resistance, wear resistance and fatigue strength of steel plate but also may cause production accidents. Therefore, the detection of steel plate surface defect must be strengthened to ensure the production quality of steel plate and the smooth development of industrial construction.

(1) A steel plate surface defect detection technology based on small datasets is proposed, which can detect multiple surface defects and fill in the blank of scab defect detection. (2) A detection system based on intelligent recognition technology is built. The steel plate images are collected by the front-end monitoring device, then transmitted to the back-end monitoring center and processed by the embedded intelligent algorithms. (3) In order to reduce the impact of external light on the image, an improved Multi-Scale Retinex (MSR) enhancement algorithm based on adaptive weight calculation is proposed, which lays the foundation for subsequent object segmentation and feature extraction. (4) According to the different factors such as the cause and shape, the texture and shape features are combined to classify different defects on the steel plate surface. The defect classification model is constructed and the classification results are recorded and stored, which has certain application value in the field of steel plate surface defect detection. (5) The practicability and effectiveness of the proposed method are verified by comparison with other methods, and the field running tests are conducted based on the equipment commissioning field of China Heavy Machinery Institute.

When applied to small dataset, the precision of the proposed method is 94.5% and the time is 23.7 ms. In order to compare with deep learning technology, after expanding the image dataset, the precision and detection time of this paper are 0.948 and 24.2 ms, respectively. The proposed method is superior to other traditional image processing and deep learning methods. And the field recognition precision is 91.7%.

In brief, the steel plate surface defect detection technology based on computer vision is effective, but the previous attempts and methods are not comprehensive and the accuracy and detection speed need to be improved. Therefore, a more practical and comprehensive technology is developed in this paper. The main contributions are as follows: (1) A steel plate surface defect detection technology based on small datasets is proposed, which can detect multiple surface defects and fill in the blank of scab defect detection. (2) A detection system based on intelligent recognition technology is built. The steel plate images are collected by the front-end monitoring device, then transmitted to the back-end monitoring center and processed by the embedded intelligent algorithms. (3) In order to reduce the impact of external light on the image, an improved MSR enhancement algorithm based on adaptive weight calculation is proposed, which lays the foundation for subsequent object segmentation and feature extraction. (4) According to the different factors such as the cause and shape, the texture and shape features are combined to classify different defects on the steel plate surface. The defect classification model is constructed and the classification results are recorded and stored, which has certain application value in the field of steel plate surface defect detection. (5) The practicability and effectiveness of the proposed method are verified by comparison with other methods, and the field running tests are conducted based on the equipment commissioning field of China Heavy Machinery Institute.

This study aims to investigate the performance of filament-based material extrusion additive manufacturing (MEX), combined with debinding and sintering, as a novel approach to manufacturing ceramic components.

A commercial ZrO₂ filament was selected and analysed by infra-red (IR) spectroscopy, rheology and thermo-gravimetry. The influence of the print parameters (layer thickness, flow rate multiplier, printing speed) and sintering cycle were investigated to define a suitable printing and sintering strategy. Biaxial flexure tests were applied on sintered discs realised with optimised printing strategies, and the results were analysed via Weibull statistics to evaluate the mechanical properties of printed components. The hardness and thermal conductivity of sintered components were also tested.

Layer thickness and flow rate multiplier of the printing process were proved to have significant effect on the density of as-printed parts. Optimised samples display a sintered density >99% of the theoretical density, 20% linear sintering shrinkage, a characteristic flexural strength of 871 MPa with a Weibull modulus of 4.9, a Vickers hardness of 12.90 ± 0.3 GPa and a thermal conductivity of 3.62 W/mK. Gyroids were printed for demonstration purposes.

To the best of the authors’ knowledge, this work is the first to apply biaxial flexure tests and Weibull statistics to additively manufactured MEX zirconia components, hence providing comparable results to other additive technologies. Moreover, fractography analysis builds the connection between printing defects and the fracture mechanism of bending. This study also provides guidelines for fabricating high-density zirconia components with MEX.

The purpose of this paper is to optimize and improve a bipolar charge transport (BCT) model used to simulate charge dynamics in insulating polymer materials, specifically low-density polyethylene (LDPE).

An optimization algorithm is applied to optimize the BCT model by comparing the model outputs with experimental data obtained using two kinds of measurements: space charge distribution using the pulsed electroacoustic (PEA) method and current measurements in nonstationary conditions.

The study provides an optimal set of parameters that offers a good correlation between model outputs and several experiments conducted under varying applied fields. The study evaluates the quantity of charges remaining inside the dielectric even after 24 h of short circuit. Moreover, the effects of increasing the electric field on charge trapping and detrapping rates are addressed.

This study only examined experiments with different applied electric fields, and thus the obtained parameters may not suit the experimental outputs if the experimental temperature varies. Further improvement may be achieved by introducing additional experiments or another source of measurements.

This work provides a unique set of optimal parameters that best match both current and charge density measurements for a BCT model in LDPE and demonstrates the use of trust region reflective algorithm for parameter optimization. The study also attempts to evaluate the equations used to describe charge trapping and detrapping phenomena, providing a deeper understanding of the physics behind the model.

This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved.

In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS₂ and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2  and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel.

The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss.

The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

In the analysis of structures in a fire situation by simplified and analytical methods, one assumption is that the fire resistance time is greater than or equal to the required fire resistance time. Among the methodologies involving the fire resistance time, the most used is the tabular method, which associates fire resistance time values to structural elements based on minimum dimensions of the cross section. The tabular method is widely accepted by the technical-scientific community due to the fact that it is safe and practical. However, its main criticism is that it results in lower fire resistance times than advanced thermal and thermostructural analysis methods. The objective of this study was to evaluate the fire resistance time of reinforced concrete beams and compare it with the required fire resistance time recommended by the tabular method of NBR 15200 (ABNT, 2012).

The fire resistance time and required fire resistance time of reinforced concrete beams were evaluated using, respectively, numerical models developed based on the finite element method and the tabular method of NBR 15200 (ABNT, 2012). The influence of the following parameters was investigated: longitudinal reinforcement cover, characteristic compressive strength of concrete, beam height, longitudinal reinforcement area and arrangement of steel bars.

Among the evaluated parameters, the covering of the longitudinal reinforcement proved to be more relevant for the fire resistance time, justifying that the tabular method of NBR 15200 (ABNT, 2012) being strongly and directly influenced by this parameter. In turn, more resistant concretes, higher beams and higher steel grades have lower fire resistance time values. This is because beams in these conditions have greater resistance capacity at room temperature and, consequently, are subject to external stresses of greater magnitude. In some cases, the fire resistance time was even lower than the required fire resistance time prescribed by NBR 15200 (ABNT, 2012). Both the fire resistance time and the required fire resistance time were not influenced by the arrangement of the longitudinal reinforcements.

The present paper innovates by demonstrating the influence of other important design variables on the required fire resistance time of the NBR 15200 (ABNT, 2012). Among several conclusions, it was found that the load level to which the structural elements are subjected considerably affects their fire resistance time. For this reason, it was recommended that the methods for calculating the required fire resistance time consider the load level. In addition, the article quantifies the security degree of the tabular method and exposes some situations for which the tabular method proved to be unsafe. Moreover, in all the models analyzed, the relationship between the span and the vertical deflection associated with the failure of the beams in a fire situation was determined. With this, a span over average deflection relationship was presented in which beams in fire situations fail.

An excessive increase in temperature will reduce the lifespan and even burn the coil. The variety of materials in the structure of the electromagnet along with its multi-layer winding creates a complex and heterogeneous thermal structure. There are very few researches that are completely focused on the thermal analysis of electromagnets. The purpose of this paper is to provide an accurate, yet fast and simple method for the thermal analysis of cylindrical electromagnets in both transient and steady-state modes. For this purpose, a thermal equivalent circuit (TEC) is presented based on the nodding approach.

The results of TEC analysis of cylindrical electromagnet, for two orthogonal and orthocyclic winding coil technologies, were compared with the results of the thermal simulation in COMSOL. The authors also built a laboratory model of the cylindrical electromagnet, similar to those analyzed and simulated, and measured the temperature in different parts of it.

The comparison of the results obtained from different methods for the thermal analysis of the cylindrical electromagnet indicates that the proposed TEC has an error of less than 2%. The simplicity and high accuracy of the results are the most important advantages of the proposed TEC.

Comparing the information and results related to winding schemes, indicates that the orthogonal winding has less cost and weight due to the shorter length of the wire used. On the other hand, orthocyclic winding generates lower temperature and has more lifting force, and is simpler to implement. Therefore, in practice, orthocyclic winding technology is usually used.

Mycelium is an upcoming bio-based alternative material that has various applications in different industries. Mycelium materials used as composites, leather, construction materials and some are even available for commercial purposes. However, there was not much research found when it came to the application of mycelium as a textile alternative. The purpose of this paper is to examine the potential of mycelium in the textile industry and its possible applications.

This review consolidates literature that refers the two major methods used in fungal mycelium production namely; as a composite and as a pure self-grown mycelium sheet. The study compared the current research status in this respective field and reported the scope in the pure mycelium development.

The results of the review reported that several research works are performed in composite production with different feedstock. The production methods and product development steps were well established for several applications from home utilities to construction materials. Whereas, in the case of self-grown mycelium sheet production only limited research works were found. Though the possibilities of engineered composite sheets are developed with various properties, research on self-grown pure mycelium sheets are at infant stage. Sensitive production methods, lower tensile, tearing, poor handle properties with brittle structure and non-uniformity in thickness are noted as limitations. Sustainable nature, self-grown three-dimensional nano-fibril network with porous structure are found to be advantageous.

The solid culture method was identified as a potential method to develop a sheet-like self-grown mycelium with different dimensions. The review results clearly show the lack of research in the direct application of self-grown pure mycelium area concerning feedstock material, fungal species selection and characterization of the developed product. Addressing the existing limitations will yield a sustainable textile material for fashion and textile industry with great potential.