Search results

This paper aims to improve the device performance from the perspective of reducing ohmic contact resistance; the effects of different electrode structures and alloying parameters on the series resistance and power-current-voltage of laser diodes (LDs) have been investigated in this paper.

Four groups of p-GaAs side metal electrodes with different metal layer arrangements and thicknesses are fabricated for the investigated LDs. The investigated p-GaAs side electrodes are based on Ti/Pt/Au material and the n-GaAs side metal electrodes all have a same structure of Ni/Ge/Ni/Au/Ti/Pt/Au. The LDs with different electrodes were alloyed at 380°C for 60 s and 420°C for 80 s.

The experimental results show that the series resistance decreases by 14%–20%, the output power increases by 2%–2.2% and the conversion efficiency increases by 1.69%–2.16% for the LDs prepared with optimized alloying parameters (420°C for 80 s). The laser diode with p-GaAs side Ti/Pt/Au electrode of 30/70/100 nm has the best device characteristics under both annealing conditions.

The utilization of this improvement on ohmic contact property in electrode is not only very important for upgrading high-power LDs but also helpful for GaAs-based microelectronic devices such as HBT and monolithic microwave integrated circuit.

The purpose of this paper is to achieve the multi-objective optimization design of novel tubular switched reluctance motor (TSRM).

First, the structure and initial dimensions of TSRM are obtained based on design criteria and requirements. Second, the sensitivity analysis rules, process and results of TSRM are performed. Third, three optimization objectives are determined by the average electromagnetic force, smoothing coefficient and copper loss ratio. The analytic hierarchy process-entropy method-a technique for order preference by similarity to an ideal solution-grey relation analysis comprehensive evaluation algorithm is used to optimize TSRM. Finally, a prototype is manufactured, a hardware platform is built and static and dynamic experimental validations are carried out.

The sensitivity analysis reveals that parameters significantly impact the performance of TSRM. The results of multi-objective optimization show that the average electromagnetic force and smoothing coefficient after optimization are better than before, and the copper loss ratio reduces slightly. The experimental and simulated results of TSRM are consistent, which verifies the accuracy of TSRM.

In this paper, only three optimization objectives are selected in the multi-objective optimization process. To improve the performance of TSRM, the heating characteristics, such as iron loss, can be considered as the optimization objective for a more comprehensive analysis of TSRM performance.

A novel motor structure is designed, combining the advantages of the TSRM and the linear motor. The established sensitivity analysis rules are scientific and suitable for the effects of various parameters on motor performance. The proposed multi-objective optimization algorithm is a comprehensive evaluation algorithm. It considers subjective weight and objective weight and fully uses the original data and the relational degree between the optimization objectives.

Given the regional heterogeneity of economic development, electricity consumption in various regions exhibits a discrepant growth pattern. The purpose of this study is to construct a grey system forecasting model with intelligent parameters for predicting provincial electricity consumption in China.

First, parameter optimization and structural expansion are simultaneously integrated into a unified grey system prediction framework, enhancing its adaptive capabilities. Second, by setting the minimum simulation percentage error as the optimization goal, the authors apply the particle swarm optimization (PSO) algorithm to search for the optimal grey generation order and background value coefficient. Third, to assess the performance across diverse power consumption systems, the authors use two electricity consumption cases and select eight other benchmark models to analyze the simulation and prediction errors. Further, the authors conduct simulations and trend predictions using data from all 31 provinces in China, analyzing and predicting the development trends in electricity consumption for each province from 2021 to 2026.

The study identifies significant heterogeneity in the development trends of electricity consumption systems among diverse provinces in China. The grey prediction model, optimized with multiple intelligent parameters, demonstrates superior adaptability and dynamic adjustment capabilities compared to traditional fixed-parameter models. Outperforming benchmark models across various evaluation indicators such as root mean square error (RMSE), average percentage error and Theil’s index, the new model establishes its robustness in predicting electricity system behavior.

Acknowledging the limitations of traditional grey prediction models in capturing diverse growth patterns under fixed-generation orders, single structures and unadjustable background values, this study proposes a fractional grey intelligent prediction model with multiple parameter optimization. By incorporating multiple parameter optimizations and structure expansion, it substantiates the model’s superiority in forecasting provincial electricity consumption.

The heat transfer properties play significant roles in the thermal comfort of the clothing products. The purpose of this paper is to find the relationship between heat transfer properties and fabrics' structure, yarn properties and predict the effective thermal conductivity of single layer woven fabrics by a parametric mathematical model.

First, the weave unit was divided into four types of element regions, including yarn overlap regions, yarn crossing regions, yarn floating regions and pore regions. Second, the number and area proportion of each region were calculated respectively. Some formulas were created to calculate the effective thermal conductivity of each element region based on serial model, parallel model or series–parallel mixing model. Finally, according to the number and area proportion of each region in weave unit, the formulas were established to calculate the fabric overall effective thermal conductivity in thickness direction based on the parallel models.

The influences of yarn spacing, yarn width, fabric thickness, the compressing coefficients of air layers and weave type on the effective thermal conductivity were further discussed respectively. In this model, the relationships between the effective thermal conductivity and each parameter are some polynomial fitting curves with different orders. Weave type affects the change of effective thermal conductivity mainly through the numbers of different elements and their area ratios.

In this model, the formulas were created respectively to calculate the effective thermal conductivity of each element region and whole weave unit. The serial–parallel mixing characteristics of yarn and surrounding air are considered, as well as the compression coefficients of air layers. The results of this study can be further applied to the optimal design of mixture fabrics with different warp and filling yarn densities or different yarn thermal properties.

Additive manufacturing (AM), a rapidly evolving paradigm, has shown significant advantages over traditional subtractive processing routines by allowing for the custom creation of structural components with enhanced performance. Numerous studies have shown that the technical qualities of AM components are profoundly affected by the discovery of novel metastable substructures in diverse alloys. Therefore, the purpose of this study is to determine the effect of cell structure parameters on its mechanical response.

Initially, a methodology was suggested for testing porous materials, focusing on static tensile testing. For a qualitative evaluation of the cellular structures produced, computed tomography (CT) was used. Then, the CT scanner was used to analyze a sample and determine its actual relative density, as well as perform a detailed geometric analysis.

The experimental research demonstrates that the mechanical properties of a cell’s structure are significantly influenced by its shape during formation. It was also determined that using selective laser melting to produce cell structures with a minimum single-cell size of approximately 2 mm would be the most appropriate method.

Further studies of cellular structures for testing their static tensile strength are planned for the future. The study will be carried out for a larger number of samples, taking into account a wider range of cellular structure parameters. An important step will also be the verification of the results of the static tensile test using numerical analysis for the model obtained by CT scanning.

The fabrication of metallic parts with different cellular structures is very important with a selective laser melted machine. However, the determination of cell size and structure with mechanical properties is quiet novel in this current investigation.

The rock drill’s drill tail experiences high-frequency fretting simultaneously in the rotational and axial directions. Due to the complex working characteristics and the low viscosity of the water medium, the pure water seal is susceptible to damage and failure. The purpose of this paper is to enhance the water seal’s performance.

The Y-shaped seal ring is modeled and simulated using orthogonal testing. Through analysis of the impact of various seal section parameters on sealing performance, the maximum contact stress and maximum Von Mises stress are selected as indicators of sealing effectiveness.

The maximum contact stress is proportional to lip thickness and chamfer length but inversely proportional to lip length. Meanwhile, the maximum Von Mises stress is directly influenced by lip depth and the included angle of the lip and drill tail but is inversely proportional to the lip thickness. The enhanced Y-shaped water seal sees reductions of 15% and 45% in maximum contact stress and maximum Von Mises stress, respectively.

This paper used analytical method and model that is helpful for design of the water seal’s structure in complex working characteristics and the low viscosity of the water medium.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-11-2023-0366/

The main issue in the mass customization of apparel products is how to efficiently produce products of various sizes. A parametric pattern-making system is one of the notable ways to rectify this issue, but there is a lack of information on the parametric design itself and its application to the apparel industry. This study compares and analyzes three types of parametric clothing pattern CAD (P-CAD) software currently in use to identify the characteristics of each, and suggest a basic guideline for efficient and adaptable P-CAD software in the apparel industry.

This study compared three different types of P-CAD software with different characteristics: SuperALPHA: PLUS(as known as YUKA), GRAFIS and Seamly2D. The authors analyzed the types and management methodologies of each software, according to the three essential components that refer to previous studies about parametric design systems: entities, constraints and parameters.

The results demonstrated the advantages and disadvantages of methodology in terms of three essential components of each software. Based on the results, the authors proposed five strategies for P-CAD development that can be applied to the mass customization of clothing.

This study is meaningful in that it consolidates and organizes information about P-CAD software that has previously been scattered. The framework used in this study has an academic value suggesting guidelines to analyze P-CAD systems.

This paper comprehensively addresses the influence of chopped strand mat glass fiber-reinforced polymer (GFRP) patch configurations such as geometry, dimensions, position and the number of layers of patches, whether a single or double patch is used and how well debonding the area under the patch improves the strength of the cracked aluminum plates with different crack lengths.

Single-edge cracked aluminum specimens of 150 mm in length and 50 mm in width were tested using the tensile test. The cracked aluminum specimens were then repaired using GFRP patches with various configurations. A three-dimensional (3D) finite element method (FEM) was adopted to simulate the repaired cracked aluminum plates using composite patches to obtain the stress intensity factor (SIF). The numerical modeling and validation of ABAQUS software and the contour integral method for SIF calculations provide a valuable tool for further investigation and design optimization.

The width of the GFRP patches affected the efficiency of the rehabilitated cracked aluminum plate. Increasing patch width WP from 5 mm to 15 mm increases the peak load by 9.7 and 17.5%, respectively, if compared with the specimen without the patch. The efficiency of the GFRP patch in reducing the SIF increased as the number of layers increased, i.e. the maximum load was enhanced by 5%.

This study assessed repairing metallic structures using the chopped strand mat GFRP. Furthermore, it demonstrated the superiority of rectangular patches over semicircular ones, along with the benefit of using double patches for out-of-plane bending prevention and it emphasizes the detrimental effect of defects in the bonding area between the patch and the cracked component. This underlines the importance of proper surface preparation and bonding techniques for successful repair.

This paper is devoted to prepare micro-cone structure with variable cross-section size by Stereo Lithography Appearance (SLA)-based 3D additive manufacturing technology. It is mainly focused on analyzing the forming mechanism of equipment and factors affecting the forming quality and accuracy, investigating the influence of forming process parameters on the printing quality and optimization of the printing quality. This study is expected to provide a µ-SLA surface preparation technology and process parameters selection with low cost, high precision and short preparation period for microstructure forming.

The µ-SLA process is optimized based on the variable cross-section micro-cone structure printing. Multi-index analysis method was used to analyze the influence of process parameters. The process parameter influencing order is determined and validated with flawless micro array structure.

After the optimization analysis of the top diameter size, the bottom diameter size and the overall height, the influence order of the printing process parameters on the quality of the micro-cone forming is: exposure time (B), print layer thickness (A) and number of vibrations (C). The optimal scheme is A1B3C1, that is, the layer thickness of 5 µm, the exposure time of 3000 ms and the vibration of 64x. At this time, the cone structure with the bottom diameter of 50 µm and the cone angle of 5° could obtain a better surface structure.

This study is expected to provide a µ-SLA surface preparation technology and process parameters selection with low cost, high precision and short preparation period for microstructure forming.

A semiparametric stochastic frontier model is proposed for panel data, incorporating several flexible features. First, a constant elasticity of substitution (CES) production frontier is considered without log-transformation to prevent induced non-negligible estimation bias. Second, the model flexibility is improved via semiparameterization, where the technology is an unknown function of a set of environment variables. The technology function accounts for latent heterogeneity across individual units, which can be freely correlated with inputs, environment variables, and/or inefficiency determinants. Furthermore, the technology function incorporates a single-index structure to circumvent the curse of dimensionality. Third, distributional assumptions are eschewed on both stochastic noise and inefficiency for model identification. Instead, only the conditional mean of the inefficiency is assumed, which depends on related determinants with a wide range of choice, via a positive parametric function. As a result, technical efficiency is constructed without relying on an assumed distribution on composite error. The model provides flexible structures on both the production frontier and inefficiency, thereby alleviating the risk of model misspecification in production and efficiency analysis. The estimator involves a series based nonlinear least squares estimation for the unknown parameters and a kernel based local estimation for the technology function. Promising finite-sample performance is demonstrated through simulations, and the model is applied to investigate productive efficiency among OECD countries from 1970–2019.