Search results

IN reviewing the progress and promise of turbine‐engined transport aircraft, it is intended to cover pure jet, propeller turbine and compound turbine engines impartially. If the emphasis tends to fall on problems covering the installation and control of propeller turbines, this is because the author has been most closely connected with this type of engine in the past few years.

Pusher configured turbo-prop aircraft receive inadequate ram air cooling due to the lack of propeller slipstream, particularly during ground operations. However, flow entrainment can be exploited to a greater extent by placing the oil-cooler duct close to downstream of the propeller at a suitable radial location. But this method has a detrimental effect on the propeller thrust. The purpose of this paper is to discuss the results of numerical simulations carried out to simulate the performance of the propeller with and without oil cooler.

In this paper, three-dimensional (3D) numerical simulations are carried out to simulate the propeller in a rotating domain using an unstructured grid. A computational fluid dynamics solver is put forward to analyze the effect of thrust loss by solving 3D Navier-Stokes equations using a second-order upwind finite-volume scheme. In this study, the impact of thrust loss incurred in the propeller flow field with and without oil cooler duct for three different locations at various rotational speeds is carried out to assess the propeller performance and to identify the optimum position to get a sufficient mass flow rate.

The findings from this study are simulated thrust values of an uninstalled five-bladed propeller of light transport aircraft (LTA) match well with original equipment manufacturer propeller thrust data. The tip speed velocities simulated for different operating conditions are in good agreement with the theoretical calculations. The influence of oil-cooler effect on the propeller flow field is less in low velocity to high-velocity operating condition due to flow transition from laminar to turbulent. The presence of the oil cooler, which influences the thrust loss, is studied at propeller upstream and downstream locations in detail for 30%, 40% and 50% of propeller radius cases.

Simulations with finer and structured hexa grids can be applied to this problem to get closer results and save solver time as future work.

The recommended system is installed in the production standard aircraft of LTA. After installation oil cooler performance is better compared to the previous arrangement.

Research work about pusher aircraft is very limited. The problem addressed in this study is unique which resolves the major issue of pusher aircraft. This work highlights the difficulty involved in LTA engine oil cooling, and solution methodologies are also provided. Numerical simulation with oil-cooler assembly is a new area of research that gave the solution for this oil-cooling issue through various oil-cooler case studies.

EACH September the eyes of the aeronautical World turn towards the S.B.A.C. Air Display and Exhibition with interest unequalled by any other event. It is fitting that the Display is now held each year at the airfield of the Royal Aircraft Establishment, one of the world's most prominent aeronautical research centres. This interest becomes increasingly keen too, as the preview day comes closer, because new prototypes of unorthodox designs often appear a short time before the Show to illustrate the results of years of careful planning, development and research of the particular company. These designs often mould the path of progress for smaller countries without the economic resources to forge the way ahead alone. Most British citizens are very proud of their country's place in aviation today, both in the military and civil fields. This is understood by most foreigners because it is clear that Britain has won a place in aeronautical development second to none.

This document presents a Particular Risks Assessment (PRA) performed on an Uncontained Engine Rotor Failure (UERF) event for the new aircraft design hybrid Extremely Short Take Off and Landing All Surface (ESTOLAS) aircraft. All three propellers of the ESTOLAS (one hub propeller and two feed propellers) are evaluated for their impact on the aircraft in case of an UERF. The purpose of this paper is to present an illustration of the safety analysis and its requirement in new aircraft development.

The methodology used is in accordance with the aerospace industry safety standard Society of Automobile Engineers (SAE) Aerospace Recommended Practices (ARP) 4,761 (Guidelines and Methods for Conducting the Safety Assessment Process on Civil Airborne Systems and Equipment). Trajectory analyses are used on a digital mock-up of the aircraft to simulate the movement of the propeller blade fragments and its effect on the aircraft and its systems.

The paper provides an insight into the industry practice of performing PRA on new aircraft designs. The study identifies safe and unsafe regions of the aircraft, with the UERF event in mind. Technical solutions are suggested to minimize the damage to the aircraft and its systems.

This document fulfills the originality criterion, since it is an analysis performed on a new aircraft design – the ESTOLAS.

TO say that the Twenty‐fourth S.B.A.C. Show was an unqualified success is perhaps to gild the lily. True there were disappointments— the delay which kept the TSR‐2 on the ground until well after the Show being one—but on the whole the British industry was well pleased with Farnborough week and if future sales could be related to the number of visitors then the order books would be full for many years to come. The total attendance at the Show was well over 400,000—this figure including just under 300,000 members of the public who paid to enter on the last three days of the Show. Those who argued in favour of allowing a two‐year interval between the 1962 Show and this one seem to be fully vindicated, for these attendance figures are an all‐time record. This augurs well for the future for it would appear that potential customers from overseas are still anxious to attend the Farnborough Show, while the public attendance figures indicate that Britain is still air‐minded to a very healthy degree. It is difficult to pick out any one feature or even one aircraft as being really outstanding at Farnborough, but certainly the range of rear‐engined civil jets (HS. 125, BAC One‐Eleven, Trident and VCIQ) served as a re‐minder that British aeronautical engineering prowess is without parallel, while the number of rotorcraft to be seen in the flying display empha‐sized the growing importance of the helicopter in both civil and military operations. As far as the value of Farnborough is concerned, it is certainly a most useful shop window for British aerospace products, and if few new orders are actually received at Farnborough, a very large number are announced— as our ’Orders and Contracts' column on page 332 bears witness. It is not possible to cover every exhibit displayed at the Farnborough Show but the following report describes a wide cross‐section beginning with the exhibits of the major airframe and engine companies.

Normalair‐Garrett Ltd., (Stand No. N31) part of the Westland plc Group of Yeovil, Somerset, is exhibiting a wide range of products which demonstrate the company's diverse capabilities in control systems and precision components for the aerospace industry.

APPLIED Technology, Middle East and European marketing and technical support representative of PF Industries Inc, will exhibit ground support equipment supplied to airlines worldwide.