Search results

This paper aims to develop a novel protocol for the synthesis of disperse dyes derived by a triple cascade reaction with lawsone in presence of Zn acetate as a catalyst. The developed novel scaffolds have efficient dyeing properties on nylon and polyester fibers.

This report demonstrates an effectual triple cascade protocol for the synthesis of novel disperse dyes derived from various polynuclear carbaldehyde, urea and lawsone. The Zn acetate was found to be an effective catalyst for this reaction. Their dyeing performance has been studied on nylon and polyester fabrics. The wash fastness, sublimation fastness, color assessment, determination of percentage exhaustion and fixation properties were applied to both the dyed fabrics.

The obtained results indicate that the Zn acetate is an efficient catalyst for the developed triple cascade protocol. The prepared novel disperse dye greatly impacted their dyeing properties on nylon and polyester fibers. They have shown brilliant shades, higher affinity, adsorption capacity, superior tinctorial strength than the lawsone. The percentage exhaustion value, fixation value, color strength (K/s) value, washing and sublimation fastness properties have been found very well in all dyed nylon samples compared to polyester samples. These results discloses that these disperses dyes are very useful to the growing importance of nylon and polyester fibers.

The present protocol synthesizes the racemic mixture of the prepared molecules.

Developed protocol can be used for various other triple cascade processes. Also these molecules can be used for dyeing of other fabrics.

With the help of commercialization of prepared molecules, it may provide the better alternative of the current disperse dyes. This may affect the various segments of society.

This report represents a novel protocol for the synthesis of modified novel disperse dyes with an efficient dyeing properties on nylon and polyester fibers.

The purpose of this study was to determine whether there are differences in skin temperature under graphene-infused fleece and traditional polyester fleece materials in the interior of a wetsuit.

A total of 48 participants surfed for a minimum of 40 min in a custom wetsuit with a torso lined with graphene-infused fleece on one half and traditional polyester fleece on the other. Eight iButton thermistors were used to record skin temperatures bilaterally at the upper back, chest, abdomen and lower back every minute for the entire surf session. After surfing, participants responded to questions associated with their perception of warmth and comfort and their knowledge of fleece materials.

Skin temperatures did not differ between the two types of fleece at the upper back, chest and abdomen locations. Skin temperatures in the lower back were significantly warmer under the traditional polyester fleece compared to graphene-infused fleece. Participant responses associated with warmth were consistent with skin temperature measurements.

The results of this study indicate that a graphene-infused nylon fleece interior does not clearly influence skin temperature in surfers when compared to a traditional polyester fleece interior. While skin temperatures were significantly lower under the graphene-infused nylon fleece at the low back, the other three anatomical locations did not exhibit significant differences.

Thermoregulation is an important consideration for the safety and performance of surfers in the ocean. Evidence suggests that the inner lining of a wetsuit may impact thermoregulation while surfing; however, no prior studies have compared interior materials.

Material extrusion-based additive manufacturing is a prominent manufacturing technique to fabricate complex geometrical three-dimensional (3D) parts. Despite the indisputable advantages of material extrusion-based technique, the poor surface and subsurface integrity hinder the industrial application of this technology. The purpose of this study is introducing the hot air jet treatment (HAJ) technique for surface treatment of additive manufactured parts.

In the presented research, novel theoretical formulation and finite element models are developed to study and model the polishing mechanism of printed parts surface through the HAJ technique. The model correlates reflow material volume, layer width and layer height. The reflow material volume is a function of treatment temperature, treatment velocity and HAJ velocity. The values of reflow material volume are obtained through the finite element modeling model due to the complexity of the interactions between thermal and mechanical phenomena. The theoretical model presumptions are validated through experiments, and the results show that the treatment parameters have a significant impact on the surface characteristics, hardness and dimensional variations of the treated surface.

The results demonstrate that the average value of error between the calculated theoretical results and experimental results is 14.3%. Meanwhile, the 3D plots of Ra and Rq revealed that the maximum values of Ra and Rq reduction percentages at 255°C, 270°C, 285°C and 300°C treatment temperatures are (35.9%, 33.9%), (77.6%,76.4%), (94%, 93.8%) and (85.1%, 84%), respectively. The scanning electron microscope results illustrate three different treatment zones and the treatment-induced and manufacturing-induced entrapped air relief phenomenon. The measured results of hardness variation percentages and dimensional deviation percentages at different regimes are (8.33%, 0.19%), (10.55%, 0.31%) and (−0.27%, 0.34%), respectively.

While some studies have investigated the effect of the HAJ process on the structural integrity of manufactured items, there is a dearth of research on the underlying treatment mechanism, the integrity of the treated surface and the subsurface characteristics of the treated surface.