Search results

This study aims to evaluate the efficiency of various techniques for enhancing indoor air quality (IAQ) in construction. It analyzed the alterations in the concentration of indoor air pollutants over time for each product employed in controlling pollution sources and removing it, which included eco-friendly substances and adsorbents. The study will provide more precise and dependable data on the effectiveness of these control methods, ultimately supporting the creation of more efficient and sustainable approaches for managing indoor air pollution in buildings.

The research investigates the impact of eco-friendly materials and adsorbents on improving indoor air quality (IAQ) in Dubai's tall apartment buildings. Field experiments were conducted in six units of The Gate Tower, comparing the IAQ of three units built with “excellent” grade eco-friendly materials with three built with “good” grade materials. Another experiment evaluated two adsorbent products (H and Z) in the Majestic Tower over six months. Results indicate that “excellent” grade materials significantly reduced toluene emissions. Adsorbent product Z showed promising results in pollutant reduction, but there is concern about the long-term behavior of adsorbed chemicals. The study emphasizes further research on household pollutant management.

The research studied the effects of eco-friendly materials and adsorbents on indoor air quality in Dubai's new apartments. It found that apartments using “excellent” eco-friendly materials had significantly better air quality, particularly reduced toluene concentrations, compared to those using “good” materials. However, high formaldehyde (HCHO) emissions were observed from wood products. While certain construction materials led to increased ethylbenzene and xylene levels, adsorbent product Z showed promise in reducing pollutants. Yet, there is a potential concern about the long-term rerelease of these trapped chemicals. The study emphasizes the need for ongoing research in indoor pollutant management.

The research, while extensive, faced limitations in assessing the long-term behavior of adsorbed chemicals, particularly the potential for rereleasing trapped pollutants over time. Despite the study spanning a considerable period, indoor air pollutant concentrations in target households did not stabilize, making it challenging to determine definitive improvement effects and reduction rates among products. Comparisons were primarily relative between target units, and the rapid rise in pollutants during furniture introduction warrants further examination. Consequently, while the research provides essential insights, it underscores the need for more prolonged and comprehensive evaluations to fully understand the materials' and adsorbents' impacts on indoor air quality.

The research underscores the importance of choosing eco-friendly materials in new apartment constructions for better IAQ. Specifically, using “excellent” graded materials can significantly reduce harmful pollutants like toluene. However, the study also highlights that certain construction activities, such as introducing furniture, can rapidly elevate pollutant levels. Moreover, while adsorbents like product Z showed promise in reducing pollutants, there is potential for adsorbed chemicals to be rereleased over time. For practical implementation, prioritizing higher-grade eco-friendly materials and further investigation into furniture emissions and long-term behavior of adsorbents can lead to healthier indoor environments in newly built apartments.

The research offers a unique empirical assessment of eco-friendly materials' impact on indoor air quality within Dubai's rapidly constructed apartment buildings. Through field experiments, it directly compares different material grades, providing concrete data on pollutant levels in newly built environments. Additionally, it explores the efficacy of specific adsorbents, which is of high value to the construction and public health sectors. The findings shed light on how construction choices can influence indoor air pollution, offering valuable insights to builders, policymakers and residents aiming to promote public health and safety in urban living spaces.

This study aimed to characterize the concentrations of indoor pollutants (such as carbon dioxide (CO₂), ozone (O₃), nitrogen dioxide (NO₂) and sulfur dioxide (SO₂), as well as particulate matter (PM) (PM₁, PM_2.5 and PM₁₀) in Akure, Nigeria, as well as the relationship between the parameters’ concentrations.

The evaluation, which lasted four months, used a low-cost air sensor that was positioned two meters above the ground. All sensor procedures were correctly carried out.

CO₂ (430.34 ppm), NO₂ (93.31 ppb), O₃ (19.94 ppb), SO₂ (40.87 ppb), PM₁ (29.31 µg/m3), PM_2.5 (43.56 µg/m³), PM₁₀ (50.70 µg/m³), temperature (32.4°C) and relative humidity (50.53%) were the average values obtained. The Pearson correlation depicted the relationships between the pollutants and weather factors. With the exception of April, which had significant SO₂ (18%) and low PM₁₀ (49%) contributions, NO₂ and PM₁₀ were the most common pollutants in all of the months. The mean air quality index (AQI) for NO₂ indicated that the AQI was “moderate” (51–100). In contrast to SO₂, whose AQI ranged from “moderate” to “very unhealthy,” O₃'s AQI ranged from “good” (50) to “unhealthy” (151–200). Since PM₁, PM_2.5 and PM₁₀ made up the majority of PC1’s contribution, both PM_2.5 and PM₁₀ were deemed “hazardous.”

The practical implication of indoor air pollution is long-term health effects, including heart disease, lung cancer and respiratory diseases such as emphysema. Indoor air pollution can also cause long-term damage to people’s nerves, brain, kidneys, liver and other organs.

Lack of literature in terms of indoor air quality (IAQ) in Akure, Ondo State. With this work, the information obtained will assist all stakeholders in policy formulation and implementation. Again, the low-cost sensor used is new to this part of the world.

Achieving an appropriate indoor environment quality (IEQ) is crucial to a green office environment. Whilst much research has been carried out across the globe on the ideal IEQ for green offices, little is known about which indoor environment New Zealand office workers prefer and regard as most appropriate. This study investigated New Zealand office workers' preference for a green environment.

Workers were conveniently selected for a questionnaire survey study from two major cities in the country – Wellington and Auckland. The perception of 149 workers was analysed and discussed based on the workers' demographics. The responses to each question were analysed based on the mean, standard deviation, frequency of responses and difference in opinion.

The results showed that workers' preferences for an ideal IEQ in green work environments depend largely on demographics. New Zealand office workers prefer work environments to have more fresh air and rely on mixed-mode ventilation and lighting systems. Also New Zealand office workers like to have better acoustic quality with less distraction and background noise. Regarding temperature, workers prefer workspaces to be neither cooler nor warmer. Unique to New Zealand workers, the workers prefer to have some (not complete) individual control over the IEQ in offices.

This study was conducted in the summer season, which could have impacted the responses received. Also the sample size was limited to two major cities in the country. Further studies should be conducted in other regions and during different seasons.

This study provides the opportunity for more studies in this area of research and highlights significant findings worthy of critical investigations. The results of this study benefit various stakeholders, such as facilities managers and workplace designers, and support proactive response approaches to achieving building occupants' preferences for an ideal work environment.

This study is the first research in New Zealand to explore worker preferences of IEQ that is not limited to a particular building, expanding the body of knowledge on workers' perception of the ideal work environment in the country.

This study aims to assess the effect of water variation on bioethanol production from cassava peels (CP) using Saccharomyces cerevisiae yeast as the ethanologenic agent.

The milled CP was divided into three treatment groups in a small-scale flask experiment where each 20 g CP was subjected to two-stage hydrolysis. Different amount of water was added to the fermentation process of CP. The fermented samples were collected every 24 h for various analyses.

The results of the fermentation revealed that the highest ethanol productivity and fermentation efficiency was obtained at 17.38 ± 0.30% and 0.139 ± 0.003 gL⁻¹ h⁻¹. The study affirmed that ethanol production was increased for the addition of water up to 35% for the CP hydrolysate process.

The finding of this study demonstrates that S. cerevisiae is the key player in industrial ethanol production among a variety of yeasts that produce ethanol through sugar fermentation. In order to design truly sustainable processes, it should be expanded to include a thorough analysis and the gradual scaling-up of this process to an industrial level.

This paper is an original research work dealing with bioethanol production from CP using S. cerevisiae microbe.

1. Hydrolysis of cassava peels using 13.1 M H₂SO₄ at 100 ^oC for 110 min gave high Glucose productivity

2. Highest ethanol production was obtained at 72 h of fermentation using Saccharomyces cerevisiae

3. Optimal bioethanol concentration and yield were obtained at a hydration level of 35% agitation

4. Highest ethanol productivity and fermentation efficiency were 17.3%, 0.139 g.L⁻¹.h⁻¹

Hydrolysis of cassava peels using 13.1 M H₂SO₄ at 100 ^oC for 110 min gave high Glucose productivity

Highest ethanol production was obtained at 72 h of fermentation using Saccharomyces cerevisiae

Optimal bioethanol concentration and yield were obtained at a hydration level of 35% agitation

Highest ethanol productivity and fermentation efficiency were 17.3%, 0.139 g.L⁻¹.h⁻¹