Search results

The aero-engine array electrostatic monitoring technology (AEMT) can provide more and more accurate information about the direct product of the fault, and it is a novel condition monitoring technology that is expected to solve the problem of high false alarm rate of traditional electrostatic monitoring technology. However, aliasing of the array electrostatic signals often occurs, which will greatly affect the accuracy of the information identified by using the electrostatic sensor array. The purpose of this paper is to propose special solutions to the above problems.

In this paper, a method for de-aliasing of array electrostatic signals based on compressive sensing principle is proposed by taking advantage of the sparsity of the distribution of multiple pulse signals that originally constitute aliased signals in the time domain.

The proposed method is verified by finite element simulation experiments. The simulation experiments show that the proposed method can recover the original pulse signal with an accuracy of 96.0%; when the number of pulse signals does not exceed 5, the proposed method can recover the pulse peak with an average absolute error of less than 5.5%; and the recovered aliased signal time-domain waveform is very similar to the original aliased signal time-domain waveform, indicating that the proposed method is accurate.

The proposed method is one of the key technologies of AEMT.

Particles are of the controlled release delivery systems. Also, topically applied olive oil has a protective effect against ultraviolet B (UVB) exposure. Due to its sensitivity to oxidation, various studies have investigated the production of olive oil particles. The purpose of this study was to use chitosan and sodium alginate as the vehicle polymers for olive oil.

The gelation method used to prepare the sodium alginate miliparticles containing olive oil and particles were coated with chitosan. Morphology and size, zeta potential, infrared spectrum of olive oil miliparticles, encapsulation efficiency and oil release profile were investigated. Among 12 primary fabricated formulations, formulations F₅ (olive oil loaded alginate miliparticles) and F₁₁ (olive oil loaded alginate miliparticles + chitosan coat) were selected for further evaluations.

The size of the miliparticles was in the range of 1,100–1,600 µm. Particles had a spherical appearance, and chitosan coat made a smoother surface according to the scanning electron microscopy. The zeta potential of miliparticles were −30 mV for F₅ and +2.7 mV for F₁₁. Fourier transform infrared analysis showed that there was no interaction between olive oil and other excipients. Encapsulation efficiency showed the highest value of 85% in 1:4 (olive oil:alginate solution) miliparticles in F₁₁. Release study indicated a maximum release of 68.22% for F₅ and 60.68% for F₁₁ in 24 h (p-value < 0.016). Therefore, coating with chitosan had a marked effect on slowing the release of olive oil. These results indicated that olive oil in various amounts can be successfully encapsulated into the sodium-alginate capsules cross-linked with glutaraldehyde.

To the best of the authors’ knowledge, no study has used chitosan and sodium alginate as the vehicle polymers for microencapsulation of olive oil.

This paper aims at building a discharge model for the power cable bellows based on plasma energy deposition and analyzing the discharge ablation problem.

Aiming at the multiphysical mechanism of the discharge ablation process, a multiphysical field model based on plasma energy deposition is established to analyze the discharge characteristics of the power cable bellows. The electrostatic field, plasma characteristics, energy deposition and temperature field are analyzed. The discharge experiment is also carried out for result validation.

The physical mechanism of the bellows ablative effect caused by partial discharge is studied. The results show that the electric field intensity between the aluminum sheath and the buffer layer easily exceeds the pressure resistance value of air breakdown. On the plasma surface of the buffer layer, the electron density is about 4 × 1,019/m³, and the average temperature of electrons is about 3.5 eV. The energy deposition analysis using the Monte Carlo method shows that the electron range in the plasma is very short. The release will complete within 10 nm, and it only takes 0.1 s to increase the maximum temperature of the buffer layer to more than 1,000 K, thus causing various thermal effects.

Its physical process involves the distortion of electric field, formation of plasma, energy deposition of electrons, and abrupt change of temperature field.

This paper aims to study the physical and chemical characteristics of inkjet titanium dioxide inks for cotton fabric digital printing.

Different dispersing agents through the reaction of glycerol monooleate and toluene diisocyanate were prepared and then performed by using three different polyols (succinic anhydride-modified polyethylene glycol PEG 600, EO/PO Polyether Monoamine and p-chloro aniline Polyether Monoamine), to obtain three different dispersing agents for water-based titanium dioxide inkjet inks. The prepared dispersants were characterized using FTIR to monitor the reaction progress. Then the prepared dispersants were formulated in titanium dioxide inkjet inks formulation and characterized by particle size, dynamic surface tension, transmission electron microscopy, viscosity and zeta potential against commercial dispersants. Also, the study was extended to evaluate the printed polyester by using the prepared inks according to washing and crock fastness.

The obtained results showed that p-chloro aniline Polyether Monoamine (J) and succinic anhydride modified polyethylene glycol PEG 600 (H) dispersants provided optimum performance as compared to commercial standards especially, particle size distribution data while EO/PO Polyether Monoamine based on dispersant was against and then failed with the wettability and dispersion stability tests.

These ink formulations could be used for printing on cotton fabric by DTG technique of printing and can be used for other types of fabrics.

The newly prepared ink formulation for digital textile printing based on synthesized polyurethane prepolymers has the potential to be promising in this type of printing inks, to prevent clogging of nozzles on the printhead and to improve the print quality on the textile fiber.

The purpose of this paper is to study haemodynamic flow characteristics and entropy analysis in a bifurcated artery system subjected to stenosis, magnetohydrodynamic (MHD) flow and aneurysm conditions. The findings of this study offer significant insights into the intricate interplay encompassing electro-osmosis, MHD flow, microorganisms, Joule heating and the ternary hybrid nanofluid.

The governing equations are first non-dimensionalised, and subsequently, a coordinate transformation is used to regularise the irregular boundaries. The discretisation of the governing equations is accomplished by using the Crank–Nicolson scheme. Furthermore, the tri-diagonal matrix algorithm is applied to solve the resulting matrix arising from the discretisation.

The investigation reveals that the velocity profile experiences enhancement with an increase in the Debye–Hückel parameter, whereas the magnetic field parameter exhibits the opposite effect, reducing the velocity profile. A comparative study demonstrates the velocity distribution in Au-CuO hybrid nanofluid and Au-CuO-GO ternary hybrid nanofluid. The results indicate a notable enhancement in velocity for the ternary hybrid nanofluid compared to the hybrid nanofluids. Moreover, an increase in the Brinkmann number results in an augmentation in entropy generation.

This study investigates the flow characteristics and entropy analysis in a bifurcated artery system subjected to stenosis, MHD flow and aneurysm conditions. The governing equations are non-dimensionalised, and a coordinate transformation is applied to regularise the irregular boundaries. The Crank–Nicolson scheme is used to model blood flow in the presence of a ternary hybrid nanofluid (Au-CuO-GO/blood) within the arterial domain. The findings shed light on the complex interactions involving stenosis, MHD flow, aneurysms, Joule heating and the ternary hybrid nanofluid. The results indicate a decrease in the wall shear stress (WSS) profile with increasing stenosis size. The MHD effects are observed to influence the velocity distribution, as the velocity profile exhibits a declining nature with an increase in the Hartmann number. In addition, entropy generation increases with an enhancement in the Brinkmann number. This research contributes to understanding fluid dynamics and heat transfer mechanisms in bifurcated arteries, providing valuable insights for diagnosing and treating cardiovascular diseases.

The purpose of this study is to investigate the authors' previously prepared and fully characterized poly (methacrylamide)-chitosan nanoparticles (CNPs) graft copolymer having 50.2% graft yield with respect to flocculation efficiency for ferric laurate aqueous dispersions. This was done to compare the ability of the latter cheap, biodegradable and ecofriendly hybrid natural-synthetic polymeric substrate as a flocculant in comparison with higher cost, nonbiodegradable and harmful polyacrylamide as a well-known synthetic flocculant counterpart.

The graft copolymerization process was carried out at 450°Cfor 120 min using (1.0 g) CNPs, methacrylamide (1.5 g), 100 mmol/l potassium chromate and 80 mmol/l mandelic acid. Fourier transform infrared spectroscopy, thermogravimetric analysis, elemental analysis and specific viscosity were used to characterize and analyze the resultant copolymer. The flocculation efficiency was conferred in terms of transmittance % and weight removal %. The main factors influencing the flocculation process, such as flocculent dose, flocculation medium pH, stirring speed, flocculation temperature and grafting extent, were comprehensively discussed.

The flocculation efficiency of the prepared copolymers revealed the following findings: increased by increasing the flocculant dose, pH, temperature and stirring speed to a maximum values denoted at 30 ppm, 6.0, 30°C and 50 r/min, respectively, then decreased thereafter; increased by increasing the extent of grafting within the range studied; showed a comparable flocculation efficiency in comparison with polyacrylamide as a synthetic polymeric flocculent; and, finally, a preliminary bridging mechanism representing the attraction between the anionic suspended particles ferric laurate and cationic poly (MAam)-CNPs graft copolymer has been projected.

The advancement addressed here is undertaken with using the authors’ poly (MAam)-CNPs graft copolymers having different extent of grafting (a point which is not cited in the literature especially for the authors’ prepared copolymer) as a hybrid natural-synthetic polymeric substrate as a flocculant for ferric laurate aqueous dispersions in comparison with the high cost and nondegradable polyacrylamide synthetic flocculant.

Toner is a crucial dry colorant composite used in printing based on the electrophotographic process. The quality of printed images is greatly influenced by the toner production method and material formulation. Chemically in situ polymerization methods are currently preferred. This paper aims to optimize the characteristics of a composite produced through emulsion polymerization using common raw materials for electrophotographic toner production.

Emulsion polymerization provides the possibility to optimize the physical and color properties of the final products. Response surface methodology (RSM) was used to optimize variables affecting particle size (PS), PS distribution (PSD), glass transition temperature (T_g°C), color properties (ΔE) and monomer conversion. Box–Behnken experimental design with three levels of styrene and butyl acrylate monomer ratios, carbon black pigment and sodium dodecyl sulfate surfactant was used for RSM optimization. Additionally, thermogravimetric analysis and surface morphology of composite particles were examined.

The results indicated that colorants with small PS, narrow PSDs, spherical shape morphology, acceptable thermal and color properties and a high percentage of conversion could be easily prepared by optimization of material parameters in this method. The anticipated outcome of the present inquiry holds promise as a guiding beacon toward the realization of electrographic toner of superior quality and exceptional efficacy, a vital factor for streamlined mass production.

To the best of the authors’ knowledge, for the first time, material parameters were evaluated to determine their impact on the characteristics of emulsion polymerized toner composites.

The purpose of this article was to highlight the various methods of extrusion technologies for encapsulation of bioactive components (BACs).

BACs provide numerous health-care benefits; however, downsides, including a strong effect of organoleptic properties by reason of the bitterness and acridity of a few components, and also a short shelf-life, limit their application in food. The food industry is still demanding complicated qualities from food ingredients, which were often impossible to obtain without encapsulation such as stability, delayed release, thermal protection and an acceptable sensory profile. Various techniques such as melt injection extrusion, hot-melt extrusion, electrostatic extrusion, co-extrusion and particles from gas-saturated solutions, could be used for maintaining these characteristics.

Extrusion technology has been well used for encapsulation of bioactive chemicals in an effort to avoid their numerous downsides and to boost their use in food. The count of BACs that could be encapsulated has risen owing to the extrusion technology just as form of encapsulation. Extrusion technique also aids in the devaluation of the fragment size of encapsulated BACs, allowing for greater application in the food business.

The study reported that encapsulating BACs makes them more stable in both the product itself and in the gastrointestinal tract, so using encapsulated BACs would result in a product with stronger preventive properties.

This study aims to form composite solid lubricant coatings on the surface of bearing steel, which can significantly improve the tribological properties of thrust cylindrical roller bearings (TCRBs). Phosphating films possess microscopic porosity that typically needs to be sealed with oil, grease or wax. Due to its unique crystal structure, the phosphating film itself also exhibits a certain degree of lubricity. In this study, solid lubricants are used to fill the pores of the phosphating film. By combining the phosphating film with solid lubricants, lubrication and wear reduction can be achieved.

In this study, the surfaces of the shaft washer (WS) and seat washer (GS) were treated with zinc-phosphating. Subsequently, a solid lubricant solution (polytetrafluoroethylene [PTFE], MoS₂ and graphite) was sprayed onto the phosphated samples at concentrations of 1 , 2  and 3 g/L. The porous and adsorptive nature of the phosphating film was used to embed the solid lubricant particles into the film, thus forming a composite lubrication layer containing solid lubricants on the surface of the bearing steel.

The addition of solid lubricant materials has shown significant potential in reducing wear losses compared with phosphated samples without such additives. Increasing the amount of solid lubricant added can facilitate the formation of a transfer film, which further enhances the protective properties. However, it is important to note that excessive amounts of solid lubricant material can contribute to seizure, leading to increased wear losses of the cage and a higher average coefficient of friction (ACOF).By spraying a PTFE solution with a concentration of 2 g/L, the lowest ACOF and cage wear loss were achieved, resulting in reductions of 60.5% for the ACOF and 89.4% for the cage wear loss. Similarly, when spraying a graphite solution with a concentration of 3 g/L, the lowest wear losses for GS and WS were observed, with reductions of 51.7% for GS wear loss and 38.9% for WS wear loss.

The combination of the phosphating film and solid lubricants aims to achieve lubrication and wear reduction, providing a new approach to wear-resistant technology for TCRBs.

The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-07-2023-0231/

First, the effect of magnetic field intensity and nano-ferrofluid concentrations on surface roughness was evaluated in magnetic minimum quantity lubrication (MMQL). Then, the effect of lubricant flow rate and nozzle position on surface roughness was investigated in MQL, MMQL, electrostatic MQL (EMQL) and electromagnetic MQL (EMMQL).

This study examined the performance of MQL under magnetic and electric fields in turning AISI 304 stainless steel in terms of surface roughness and compared the results with those obtained from wet cutting and MQL turning operations. To prepare the nano-ferrofluid used in different states of MQL, Fe₃O₄ nanoparticles were added to the base fluid.

The results showed that the surface roughness under the EMMQL technique decreased by 36% and 49.4% on average compared with wet and MQL techniques, respectively. The lubrication technique affected the surface roughness by 90.2%, whereas it was 8.3% for the lubricant flow rate. EMQL and EMMQL techniques had no significant difference in their effects on surface roughness. In the innovative MMQL technique, the nano-ferrofluid concentration of 6% and magnetic field intensity of 93 G resulted in lower surface roughness of the workpiece relative to other counterparts.

Examining previously published studies showed that using nano-ferrofluids under a magnetic field for cooling purposes in machining processes have less considered by researchers. This study applies an innovative method of lubrication under the concurrent effect of magnetic and electric fields, called EMMQL, to improve the efficiency of MQL in machining hard-to-cut materials. For comprehensively inspecting the newly presented method, the effects of several parameters, including the nano-ferrofluid concentration, magnetic field intensity, lubricant flow rate and position of lubricant spray nozzle, on the surface roughness of workpiece in turning of AISI 304 stainless steel are investigated.