Search results

The purpose of this paper is to evaluate some important parameters in plate buckling of fused interlining worsted fabric with different weight and laying‐up direction. The article compares the formability of fused fabric composite by two different methods (Lindberg's hypothesis and fabric assurance by simple testing method).

Plate buckling compression behavior of fused fabric composite is investigated using a special designed clamp according to Dahlberg's test method.

The result shows that fusible interlining lay‐up angle significantly influences on buckling parameters. It is indicated that the buckling behavior of fused fabric composite against lay‐up interlining direction is in accordance with interlining buckling behavior. The result of research suggests that the formability behavior of fused fabric composite with interlining lay‐up direction is predictable according to Lindberg's method.

Experimental design is limited at low speed. Further research works are needed to perform buckling behavior of fused fabric composites at higher speeds as well as under cyclic loading conditions.

Compression plate buckling behavior of fused interlining fabrics is predictable against interlining laying‐up direction. The result of this research could be used in the area of garment quality serviceability.

The objective of the present work is to present the design optimization of composite cylindrical shell subjected to an axial compressive load and lateral pressure.

A novel optimization method is developed to predict the optimal fiber orientation in composite cylindrical shell. The optimization is carried out by coupling analytical and finite element (FE) results with a genetic algorithm (GA)-based optimization scheme developed in MATLAB. Linear eigenvalue were performed to evaluate the buckling behaviour of composite cylinders. In analytical part, besides the buckling analysis, Tsai-Wu failure criteria are employed to analyse the failure of the composite structure.

The optimal result obtained through this study is compared with traditionally used laminates with 0, 90, ±45 orientation. The results suggest that the application of this novel optimization algorithm leads to an increase of 94% in buckling strength.

The proposed optimal fiber orientation can provide a practical and efficient way for the designers to evaluate the buckling pressure of the composite shells in the design stage.

In this paper, an attempt is made to obtain buckling loads, ultimate bearing capacity and other required structural characteristics of grid structure panels. The numerical method for post-buckling behavior analysis of panels involving multiple invisible damages is also presented.

In this paper, two bidirectional stiffened composite panels are manufactured and tested. Multiple discrete invisible damages are introduced in different positions of the stringers, and the experimental and simulation investigation of buckling and post-buckling were carried out on the damaged stiffened panels.

The simulation load–displacement curves are compared with the experimental results, and it is found that the simulation model can well predict the occurrence of buckling and failure loads. The strain curve shows that the rate of strain change at the damaged site is greater than that at the undamaged site, which reflects that the debond is more likely occurred at the damaged site. The simulation verifies that the panel is usually crushed due to matrix compression and fiber–matrix shear.

In this paper, post-buckling tests and numerical simulations of bidirectional stiffened composite panels with impact damage were carried out. Two panels with four longitudinal stringers and two transverse stringers were manufactured and tested. The buckling and post-buckling characteristics of the grid structure are obtained, and the failure mechanism of the structure is explained. This is helpful for the design of wall panel structure.

This study aimed to overcome the challenging issues involved in providing high-precision eigensolutions. The accurate prediction of the buckling load bearing capacity under different crack damage locations, sizes and numbers, and analysing the influence mechanism of crack damage on buckling instability have become the needs of theoretical research and engineering practice. Accordingly, a finite element method was developed and applied to solve the elastic buckling load and buckling mode of curved beams with crack damage. However, the accuracy of the solution depends on the quality of mesh, and the solution inevitably introduces errors due to mesh. Therefore, the adaptive mesh refinement method can effectively optimise the mesh distribution and obtain high-precision solutions.

For the elastic buckling of circular curved beams with cracks, the section damage defect analogy scheme of a circular arc curved beam crack was established to simulate the crack size (depth), position and number. The h-version finite element mesh adaptive analysis method of the variable section Euler–Bernoulli beam was introduced to solve the elastic buckling problem of circular arc curved beams with crack damage. The optimised mesh and high-precision buckling load and buckling mode solutions satisfying the preset error tolerance were obtained.

The results of testing typical examples show that (1) the established section damage defect analogy scheme of circular arc curved beam crack can effectively realise the simulation of crack size (depth), position and number. The solution strictly satisfies the preset error tolerance; (2) the non-uniform mesh refinement in the algorithm can be adapted to solve the arbitrary order frequencies and modes of cracked cylindrical shells under the conditions of different ring wave numbers, crack positions and crack depths; and (3) the change in the buckling mode caused by crack damage is applicable to the study of elastic buckling under various curved beam angles and crack damage distribution conditions.

This study can provide a novel strategy for the adaptive mesh refinement for finite element analysis of elastic buckling of circular arc curved beams with crack damage. The adaptive mesh refinement method established in this study is fundamentally different from the conventional finite element method which employs the user experience to densify the meshes near the crack. It can automatically and flexibly generate a set of optimised local meshes by iteratively dividing the fine mesh near the crack, which can ensure the high accuracy of the buckling loads and modes. The micro-crack in curved beams is also characterised by weakening the cross-sectional stiffness to realise the characterisation of locations, depths and distributions of multiple crack damage, which can effectively analyse the disturbance behaviour of different forms of micro-cracks on the dynamic behaviour of beams.

It is generally known that the perforated section such as the castellated section is good to sustain distributed loads but inadequate to sustain highly concentrated loads. Therefore, it is possible to design the opening in a different arrangement of web opening to achieve section efficiency, thus improving the strength and torsional behaviour of the section with web opening. This study aims to focus on the finite element analysis of I-beam with and without openings in steel section dominated to lateral-torsional buckling behaviour.

In this work, the analysis of different sizes, shapes and arrangements of web opening is performed by using LUSAS application to conduct numerical analysis on lateral-torsional buckling behaviour. This involves three diameter sizes of web opening, five types of opening shapes and two criteria of the model.

The section with c-hexagon web opening was placed about 200-mm centre to centre and 100-mm edge distance, contribute to 7.26% increase of buckling capacity. For the section with 150-mm centre to centre and 50-mm edge distance, the occurrence of local buckling contributes to decrease of lateral buckling section capacity to 19.943 kNm, where pure lateral-torsional buckling mostly occurred because of prevented section. Besides that, the web opening diameter was also analysed. The web crippling was observed because of the increase of opening diameter from 0.67 to 0.80 D.

This contributes to a decrease in buckling capacity as figured in the contour of the deformed shape. For Model 1, an increase of buckling capacity (31.46%) is observed when the opening diameter are changed from 0.67 to 0.80 D.

Several experimental and numerical studies were performed in the past to estimate buckling capacity of corroded tubular members. However, the effect of initial imperfections has not been properly considered in most of these earlier proposed formulas. Therefore, the main objective of this paper is to propose an accurate analytical formula to determine the buckling capacity of patched corroded tubular members.

Tubular members with initial geometrical imperfections can be regarded as beam-columns because of the combination of axial load and bending moment. The proposed formula is derived for a rectangular corrosion patch. The proposed formula is verified with results from finite element analysis of corroded tubular members and experimental results. The formula is also applied to an existing offshore jacket structure to highlight its significance and applicability. It is found that the buckling capacity of jacket members in splash zone reduces significantly with ageing. This reduction is around 29 and 14% for the selected brace and leg member respectively, during the design life. Finally, it is concluded that corrosion reduces the buckling capacity significantly and the proposed formula can be easily applied by practicing engineers to give an accurate and slightly conservative estimate the remaining buckling capacity.

The main finding is the new formula which accurately and conservatively estimate the buckling capacity of corroded tubular members. The proposed formula considers the secondary effect of both initial geometrical imperfections and shifting of centroid because of corrosion.

The proposed new formula is unique and original in that it considers both secondary effects from geometrical imperfections, reduction of cross-section from corrosion wastage and shifting of centroid because of corrosion. Finally, it is concluded that corrosion reduces the buckling capacity significantly and the proposed formula can be easily applied by practicing engineers to conservatively estimate the remaining buckling capacity and verify if further, more advanced estimations are needed.

Recently, this steel section has found increasing popularity in residential, industrial and commercial buildings with their high load-carrying capacity due to the nature of high strength to weight ratio properties. However, the rise on the price of steel section should be more emphasized; therefore, the optimization in steel section design is needed to overcome the issue of material cost. As such, tapered steel sections save on material use, while the introduction of web openings allows the placement of mechanical and electrical services, plumbing and also aesthetic design considerations.

The purpose of this study is to investigate the lateral torsional buckling behavior of a tapered steel section with an ellipse-shaped opening by analyzing its structural parameters. To achieve this, the finite element analysis (FEA) of the section is modeled using LUSAS software, which allows for a detailed analysis of the section's behavior under varying loads and conditions. It involves the variation in web opening size, opening layout, opening rotation angle and the tapering ratio. Eigenvalue buckling analysis is adopted to know the parametric effects of each 108 model. The size of opening varies from 0.2 to 0.5 d of the total depth where the opening located. There are three type of layouts applied in this study, which are the layouts A, B and C. There are three types of rotation angles for the ellipse-shaped opening, including the non-rotated vertical opening and two additional types formed by rotating the opening 45 degrees clockwise and counterclockwise around the center-point of the ellipse. A fixed-free boundary condition was applied, resulting in a simulation of a cantilever beam. The models are fixed at one end with a larger depth, and free at the other end with a smaller depth. Loading condition is an application of 10 kN/m uniform distributed load in the direction of gravity along the mid-span of the top flange.

It is observed that the model 82 with Layout A, tapering ratio 0.3, opening size 0.5 d and opening rotated in 45 degree anti-clockwise direction results in the highest structural efficiency among the 108 models. Therefore, the buckling moment of model 82 is 1,013.08 kNm with structural efficiency of 481.26, which shows an increase of 3.17% compared to the controlled model.

The FEA results shows a significant increase in ductility and stiffness of the tapered steel section with elipse shape opening and consequently changes in the behaviour of yield point.

Buckling should be carefully considered in steel assemblies with members subjected to compressive stresses, such as bracing systems and truss structures, in which angles and built-up steel sections are widely employed. These type of steel members are affected by torsional and flexural-torsional buckling, but the European (EN 1993-1-2) and the American (AISC 360-16) design norms do not explicitly treat these phenomena in fire situation. In this work, improved buckling curves based on the EN 1993-1-2 were extended by exploiting a previous work of the authors. Moreover, new buckling curves of AISC 360-16 were proposed.

The buckling curves provided in the norms and the proposed ones were compared with the results of numerical investigation. Compressed angles, tee and cruciform steel members at elevated temperature were studied. More than 41,000 GMNIA analyses were performed on profiles with different lengths with sections of class 1 to 3, and they were subjected to five uniform temperature distributions (400–800 C) and with three steel grades (S235, S275, S355).

It was observed that the actual buckling curves provide unconservative or overconservative predictions for various range of slenderness of practical interest. The proposed curves allow for safer and more accurate predictions, as confirmed by statistical investigation.

This paper provides new design buckling curves for torsional and flexural-torsional buckling at elevated temperature since there is a lack of studies in the field and the design standards do not appropriately consider these phenomena.

The objective of this paper is to investigate numerically the buckling behavior of submersible composite cylinders.

By means of FEM and golden section method, the search of hoop winding layers, longitudinal winding layers and helical winding layers are studied to optimize the buckling pressure. Considering the mid-strengthening cylinder, the size and distribution of stiffeners are studied systematically.

The results show that laying the hoop winding layers in the two outer sidewalls and the longitudinal winding layers in the middle of the shell is helpful to increase the buckling pressure, and the optimal helical winding angle changes with slenderness ratio.

For mid-strengthening cylinder, the effect of helical winding angle of stiffener on buckling pressure becomes weak gradually with the increase of stiffener thickness. With the increasing of the spacing between stiffeners, the buckling pressure increases first and decreases later. What is more, the mid-strengthening cylinder is less sensitive to the initial geometric imperfections than unstiffened shells.

With the widespread use of the composites over other metallic materials in different fields of engineering, studies on damages of composite structures have assumed great importance. Among various kinds of damages, delamination is of very serious concern to composite applications. It may arise as a consequence of impact loading, stress concentration near a geometrical or material discontinuity or manufacturing defects. The presence of one or more delaminations in the composite laminate may lead to a premature collapse of the structure due to buckling at a lower level of compressive loading. So the effect of delamination on stability of composite structures needs attention and thus constitutes a problem of current interest. The purpose of this paper is to deal with both numerical and experimental investigations on buckling behaviour of single and multiple, delaminated, industry driven, woven roving glass/epoxy composite plates on clamped free clamped free (CFCF) rectangular plates.

For numerical analysis, a finite element model was developed with an eight noded two dimensional quadratic isoparametric element having five degrees of freedom per node. The elastic stiffness matrices were derived using linear first order shear deformation theory with a shear correction factor. Green's nonlinear strain equations are used to derive the geometric stiffness matrix. The computation of buckling load based on present formulation is compared with the experimental results for the effect of different parameters on critical load of the delaminated composite panels. In the experimental study, the influences of various parameters such as delamination area, fiber orientations, number of layers, aspect ratios on the buckling behaviour of single and multiple delaminated woven roving glass/epoxy composite plates were investigated. Buckling loads were measured by INSTRON 1195 machine for the delaminated composite plates.

Comparison of numerical results with experimental results showed a good agreement. Both the results revealed that the area of delaminations, fiber orientations, number of layers and aspect ratio have paramount influence on the buckling behaviour of delaminated plate.

The present study is part of Jayaram Mohanty's doctoral thesis, an original research work.