Search results

Straightness measurement of rail weld joint is of essential importance to railway maintenance. Due to the lack of efficient measurement equipment, there has been limited in-depth research on rail weld joint with a 5-m wavelength range, leaving a significant knowledge gap in this field.

In this study, the authors used the well-established inertial reference method (IR-method), and the state-of-the-art multi-point chord reference method (MCR-method). Two methods have been applied in different types of rail straightness measurement trollies, respectively. These instruments were tested in a high-speed rail section within a certain region of China. The test results were ultimately validated through using traditional straightedge and feeler gauge methods as reference data to evaluate the rail weld joint straightness within the 5-m wavelength range.

The research reveals that IR-method and MCR-method produce reasonably similar measurement results for wavelengths below 1 m. However, MCR-method outperforms IR-method in terms of accuracy for wavelengths exceeding 3 m. Furthermore, it was observed that IR-method, while operating at a slower speed, carries the risk of derailing and is incapable of detecting rail weld joints and low joints within the track.

The research compare two methods’ measurement effects in a longer wavelength range and demonstrate the superiority of MCR-method.

The purpose of this paper is to provide an overview of the evolution of service supply chain management from a behavioural operations perspective, pointing out future research directions for scholars.

This study searched five databases for relevant literature published between 2009 and 2018, selecting 64 papers for this review. The selected literature was categorised according to two dimensions: a service supply chain link perspective and a behavioural factor perspective. Comparative analysis was used to identify gaps in the literature, and five future research agendas were proposed.

In terms of the perspective of service supply chain link, extant literature primarily focuses on service supply and service co-ordination management, and less on service demand and integration management. In terms of the behavioural factor’s perspective, most focus on classic behaviour factors, with less attention paid to emerging behaviour factors. This paper thus proposes five research agendas: demand-oriented management and integrated supply chain-oriented behavioural research; broadening the understanding of the scope of behavioural operations; integrating the latest backgrounds and trends of service industry into the research; greater attention to behavioural operations in service sub-industries; and multimethod combination is encouraged to be used to dig into the interesting research problems.

This study constitutes the first systematic review of service supply chain research from a behavioural perspective. By categorising the literature into two dimensions, the state of existing research is evaluated with an eye towards future research avenues.

A feature of many non-elite sports events, especially those conducted in public places, is that they are free-to-view. The article focuses on the methodological issue of estimating spectator attendance at free-to-view events and the consequences for impact evaluation. Using empirical data from three case studies, the article outlines various approaches to measuring attendance and discusses the key issues and implications for evaluating free-to-view sports events.

This research paper aim at providing a new approach of calculating the destinations competitiveness index. How can these variables been aggregated in other to reflect the realities of very distinct productive environments? We assume that: The weighting of variables provides a better measure of destinations competitiveness. Base on the Neo-Technological theory, after a life cycle differentiation, we used a panel data approach to calculate the weight of each variable as the spearman correlation coefficient of its contribution to tourism inflows growth. After integrating these weights, we came to the point that by applying an appropriate weight to its components, we end up having a competitiveness index that significantly improve the correlation between competitiveness and tourism inflows growth.

Terrestrial laser scanning (TLS) point clouds have been widely used in deformation measurement for structures. However, reliability and accuracy of resulting deformation estimation strongly depends on quality of each step of a workflow, which are not fully addressed. This study aims to give insight error of these steps, and results of the study would be guidelines for a practical community to either develop a new workflow or refine an existing one of deformation estimation based on TLS point clouds. Thus, the main contributions of the paper are investigating point cloud registration error affecting resulting deformation estimation, identifying an appropriate segmentation method used to extract data points of a deformed surface, investigating a methodology to determine an un-deformed or a reference surface for estimating deformation, and proposing a methodology to minimize the impact of outlier, noisy data and/or mixed pixels on deformation estimation.

In practice, the quality of data point clouds and of surface extraction strongly impacts on resulting deformation estimation based on laser scanning point clouds, which can cause an incorrect decision on the state of the structure if uncertainty is available. In an effort to have more comprehensive insight into those impacts, this study addresses four issues: data errors due to data registration from multiple scanning stations (Issue 1), methods used to extract point clouds of structure surfaces (Issue 2), selection of the reference surface S_ref to measure deformation (Issue 3), and available outlier and/or mixed pixels (Issue 4). This investigation demonstrates through estimating deformation of the bridge abutment, building and an oil storage tank.

The study shows that both random sample consensus (RANSAC) and region growing–based methods [a cell-based/voxel-based region growing (CRG/VRG)] can be extracted data points of surfaces, but RANSAC is only applicable for a primary primitive surface (e.g. a plane in this study) subjected to a small deformation (case study 2 and 3) and cannot eliminate mixed pixels. On another hand, CRG and VRG impose a suitable method applied for deformed, free-form surfaces. In addition, in practice, a reference surface of a structure is mostly not available. The use of a fitting plane based on a point cloud of a current surface would cause unrealistic and inaccurate deformation because outlier data points and data points of damaged areas affect an accuracy of the fitting plane. This study would recommend the use of a reference surface determined based on a design concept/specification. A smoothing method with a spatial interval can be effectively minimize, negative impact of outlier, noisy data and/or mixed pixels on deformation estimation.

Due to difficulty in logistics, an independent measurement cannot be established to assess the deformation accuracy based on TLS data point cloud in the case studies of this research. However, common laser scanners using the time-of-flight or phase-shift principle provide point clouds with accuracy in the order of 1–6 mm, while the point clouds of triangulation scanners have sub-millimetre accuracy.

This study aims to give insight error of these steps, and the results of the study would be guidelines for a practical community to either develop a new workflow or refine an existing one of deformation estimation based on TLS point clouds.

The results of this study would provide guidelines for a practical community to either develop a new workflow or refine an existing one of deformation estimation based on TLS point clouds. A low-cost method can be applied for deformation analysis of the structure.

Although a large amount of the studies used laser scanning to measure structure deformation in the last two decades, the methods mainly applied were to measure change between two states (or epochs) of the structure surface and focused on quantifying deformation-based TLS point clouds. Those studies proved that a laser scanner could be an alternative unit to acquire spatial information for deformation monitoring. However, there are still challenges in establishing an appropriate procedure to collect a high quality of point clouds and develop methods to interpret the point clouds to obtain reliable and accurate deformation, when uncertainty, including data quality and reference information, is available. Therefore, this study demonstrates the impact of data quality in a term of point cloud registration error, selected methods for extracting point clouds of surfaces, identifying reference information, and available outlier, noisy data and/or mixed pixels on deformation estimation.

The purpose of this paper is to propose and evaluate the method for grasping a defined set of objects in an unstructured environment. To this end, the authors propose the method of integrating convolutional neural network (CNN)-based object detection and the category-free grasping method. The considered scenario is related to mobile manipulating platforms that move freely between workstations and manipulate defined objects. In this application, the robot is not positioned with respect to the table and manipulated objects. The robot detects objects in the environment and uses grasping methods to determine the reference pose of the gripper.

The authors implemented the whole pipeline which includes object detection, grasp planning and motion execution on the real robot. The selected grasping method uses raw depth images to find the configuration of the gripper. The authors compared the proposed approach with a representative grasping method that uses a 3D point cloud as an input to determine the grasp for the robotic arm equipped with a two-fingered gripper. To measure and compare the efficiency of these methods, the authors measured the success rate in various scenarios. Additionally, they evaluated the accuracy of object detection and pose estimation modules.

The performed experiments revealed that the CNN-based object detection and the category-free grasping methods can be integrated to obtain the system which allows grasping defined objects in the unstructured environment. The authors also identified the specific limitations of neural-based and point cloud-based methods. They show how the determined properties influence the performance of the whole system.

The authors identified the limitations of the proposed methods and the improvements are envisioned as part of future research.

The evaluation of the grasping and object detection methods on the mobile manipulating robot may be useful for all researchers working on the autonomy of similar platforms in various applications.

The proposed method increases the autonomy of robots in applications in the small industry which is related to repetitive tasks in a noisy and potentially risky environment. This allows reducing the human workload in these types of environments.

The main contribution of this research is the integration of the state-of-the-art methods for grasping objects with object detection methods and evaluation of the whole system on the industrial robot. Moreover, the properties of each subsystem are identified and measured.

This paper aims to introduce a method to couple truss finite elements to the material point method (MPM). It presents modeling reinforced material using MPM and describes how to consider the bond behavior between the reinforcement and the continuum.

The embedded approach is used for coupling reinforcement bars with continuum elements. This description is achieved by coupling continuum elements in the background mesh to the reinforcement bars, which are described using truss- finite elements. The coupling is implemented between the truss elements and the continuum elements in the background mesh through bond elements that allow for freely distributed truss elements independent of the continuum element discretization. The bond elements allow for modeling the bond behavior between the reinforcement and the continuum.

The paper introduces a novel method to include the reinforcement bars in the MPM applications. The reinforcement bars can be modeled without any constraints with a bond-slip constitutive model being considered.

As modeling of reinforced materials is required in a wide range of applications, a method to include the reinforcement into the MPM framework is required. The proposed approach allows for modeling reinforced material within MPM applications.

In this article, the ideas and methods behind the “patent-paper citation” are scrutinised by following the intellectual and technical development of approaches and ideas in early work on patentometrics. The aim is to study how references from patents to papers came to play a crucial role in establishing a link between science and technology.

The study comprises a conceptual history of the “patent paper citation” and its emergence as an important indicator of science and technology interaction. By tracing key references in the field, it analyses the overarching frameworks and ideas, the conceptual “hinterland”, in which the approach of studying patent references emerged.

The analysis explains how interest in patents – not only as legal and economic artefacts but also as scientific documents – became evident in the 1980s. The focus on patent citations was sparked by a need for relevant and objective indicators and by the greater availability of databases and methods. Yet, the development of patentometrics also relied on earlier research, and established theories, on the relation between science and technology.

This is the first attempt at situating patentometrics in a larger societal and scientific context. The paper offers a reflexive and nuanced analysis of the “patent-paper citation” as a theoretical and historical construct, and it calls for a broader and contextualised understanding of patent references, including their social, legal and rhetorical function.