Search results

This study aims to exploit the abundance of solar energy resources for socioeconomic development in the semi -arid Northeastern Brazil as a potent adaptation tool to global climate change. It points out a set of conjuncture factors that allow us to foresee a new paradigm of sustainable development for the region by transforming the sun’s radiant energy into electricity through distributed photovoltaic generation. The new paradigm, as presented in this essay, has the transformative potential to free the region from past regional development dogma, which was dependent on the scarce water resource, and the marginal and predatory use of its Caatinga Biome.

The research uses a pre ante design, following the procedures of scenario building, as an adaptation mechanism to climate change in the sector of energy generation and socioeconomic inclusion.

The scenarios of socioeconomic resilience to climate change based on the abundance of solar radiation, rather than the scarcity of water, demonstrates its potential as a global adaptation paradigm to climate change.

The developments proposed are dependent on federal legislation changes, allowing the small producer to be remunerated by the energy produced.

The proposed smart grid photovoltaic generation program increases the country's resiliency to the effect of droughts and climate change.

As proposed, the program allows for the reversion of a pattern of long term poverty in semi-arid Northeast Brazil.

The exploitation of the characteristics of abundance of the semiarid climate, i.e. its very condition of semi-aridity with abundant solar radiation, is itself an advantage factor toward adaption to unforeseen drought events. Extensive previous research has focused on weighting and monitoring drought i.e. the paradigm of scarcity. The interplay between exploiting Northeast Brazil’s abundant factors and climate change adaptation, especially at the small farmer levels constitutes a discovery never before contemplated.

Soft systems methodology (SSM) is well documented in the academic and management literature. Over the last 40 years, the methodology has come to be adapted depending on the tool users’ skills and experience in order to fit the problem. The purpose of this paper is to demonstrate good teaching and learning practice from a pedagogical perspective.

Dr Ian Yeoman of Victoria University of Wellington provides a personal reflection of how the methodology is used in the teaching and learning of TOUR301 Tourism Policy and Planning as a policy and scenario analysis method.

The paper articulates the seven stages of SSM from problem situation unstructured, through to Rich Pictures, vision and guiding principles, policy solutions, comparisons, feasibility and implementation stages. The paper uses a series of teaching tasks to breakdown the complexity of the methodology thus guiding students and teachers in how to deploy the methodology in the classroom.

The value of the paper demonstrates the reflective practice of SSM in action as an exemplar of good practice. The paper clearly articulates the stages of the methodology so students and teachers can adopt this approach in classroom environments following a scaffolding learning approach. The use of teaching tasks throughout the paper helps bring clarity and order thus enabling the teacher to effectively teach the subject and the students to learn. The most significant contribution of this paper is the articulation of good teaching practice in policy and scenario analysis which articulated through four learning lessons: facilitating a learning environment; the impact of visual thinking; political theory; the importance of incremental learning; and problem-based learning and international students.

This study aims to develop an assessment strategy for fire damaged infrastructures based on the implementation of quick diagnostic techniques and consistent interpretation procedures, so to determine the residual safety margin and any need for repair works.

In this perspective, several tailored non-destructive test (NDT) methods have been developed in the past two decades, providing immediate results, with no need for time-consuming laboratory analyses. Moreover, matching their indications with the calculated effects of a tentative fire scenario allows harmonizing distinct pieces of evidence in the coherent physical framework of fire dynamics and heat transfer.

This approach was followed in the investigations on a concrete overpass in Verona (Italy) after a coach violently impacted one supporting pillar and caught fire in 2017. Technical specifications of the vehicle made it possible to bound the acceptable ranges for fire load and maximum rate of heat release, while surveillance video footage indicated the duration of the burning stage. Some established NDT methods (evaluation of discolouration, de-hydroxylation and rebar hardness) were implemented, together with advanced ultrasonic tests based on pulse refraction and pulse-echo tomography.

The results clearly showed the extension of the most damaged area at the intrados of the box girders and validated the maximum heating depth, as predicted by numerical analysis of the heat transient ensuing from the localized fire model.

In cities with high density, heat is often trapped between buildings which increases the frequency and intensity of heat events. Researchers have focused on developing strategies to mitigate the negative impacts of heat in cities. Adopting green infrastructure and cooling pavements are some of the many ways to promote thermal comfort against heat. The purpose of this study is to improve microclimate conditions and thermal comfort levels in high-density living conditions in Seoul, South Korea.

This study compares six design alternatives of an apartment complex with different paving and planting systems. It also examines the thermal outcome of the alternatives under normal and extreme heat conditions to suggest strategies to secure acceptable thermal comfort levels for the inhabitants. Each alternative is analyzed using ENVI-met, a software program that simulates microclimate conditions and thermal comfort features based on relationships among buildings, vegetation and pavements.

The results indicate that grass paving was more effective than stone paving in lowering air temperature and improving thermal comfort at the near-surface level. Coniferous trees were found to be more effective than broadleaf trees in reducing temperature. Thermal comfort levels were most improved when coniferous trees were planted in paired settings.

Landscape elements show promise for the improvement of thermal conditions because it is much easier to redesign landscape elements, such as paving or planting, than to change fixed urban elements like buildings and roads. The results identified the potential of landscape design for improving microclimate and thermal comfort in urban residential complexes.

The results contribute to the literature by examining the effect of tree species and layout on thermal comfort levels, which has been rarely investigated in previous studies.

Older people with dementia (OPD) have specific housing and technology-related needs, for which various design principles exist. A model for designing environments and its constituting items for people with dementia that has a firm foundation in neurology may help guide designers in making design choices. The paper aims to discuss these issues.

A general design model is presented consisting of three principles for OPD, namely designing for ageing people; designing for a favourable state and designing for beautiful moments. The neurosciences as a whole give shape to an eminent framework explaining the behaviour of OPD. One of the objectives of this paper is to translate the design principles into design specifications and to show that these specifications can be translated in a design.

Philosophical concepts are introduced which are required to understand design for OPD. Four case studies from Dutch nursing homes are presented that show how the theory of modal aspects of the philosopher Dooyeweerd can be used to map design specifications in a systematic way.

These examples of design solutions illustrate the applicability of the model developed in this article. It emphasises the importance of the environment for supporting the daily life of OPD.

There is a need for a design model for OPD. The environment and technology should initiate positive behaviours and meaningful experiences. In this paper, a general model for the designing of environments for OPD was developed that has a firm foundation in neurology and behavioural sciences. This model consists of six distinct steps and each step can be investigated empirically. In other words, this model may lay the foundation for an evidence-based design.

This study aims to test the effects of Celliant armbands on grip strength in subjects with chronic wrist and elbow pain. Celliant® is a functional textile fabric containing minerals that emit infrared radiation (IR) in response to body heat. IR-emitting fabrics have biological effects including the reduction of pain and inflammation and the stimulation of muscle function.

A randomized placebo-controlled trial recruited 80 subjects (40 per group) with a six-month history of chronic wrist or elbow pain (carpal tunnel syndrome, epicondylitis or arthritis) to wear an armband (real Celliant or placebo fabric) on the affected wrist or elbow for two weeks. Grip strength was measured by a dynamometer before and after the two-week study.

For the placebo group, the mean grip strength increased from 47.95 ± 25.14 (baseline) to 51.69 ± 27.35 (final), whereas for the Celliant group, it increased from 46.3 ± 22.02 to 54.1 ± 25.97. The mean per cent increase over the two weeks was +7.8% for placebo and +16.8% for Celliant (p = 0.0372). No adverse effects was observed.

Limitations include the wide variation in grip strength in the participants at baseline measurement, which meant that only the percentage increase between baseline and final measurements showed a significant difference. Moreover, no subjective measurements of pain or objective neurophysiology testes was done.

Celliant armbands are easy to wear and have not been shown to produce any adverse effects. Therefore, there appears to be no barrier to prevent widespread uptake.

IR-emitting textiles have been studied for their beneficial effects, both in patients diagnosed with various disorders and also in healthy volunteers for health and wellness purposes. Although there are many types of textile technology that might be used to produce IR-emitting fabrics, including coating of the fabric with a printed layer of ceramic material, incorporating discs of mineral into the garment, the authors feel that incorporating ceramic particles into the polymer fibers from which the fabric is woven is likely to be the most efficient way of achieving the goal.

Celliant armbands appear to be effective in painful upper limb inflammatory disorders, and further studies are warranted. The mechanism of action is not completely understood, but the hypothesis that the emitted IR radiation is absorbed by nanostructured intracellular water provides some theoretical justification.

The present shift and change in the human lifestyle across the world are undeniable. Currently, individuals spend a substantial amount of time indoors due to the global COVID-19 pandemic that strikes the entire world. This change in human lifestyle has devastating effects on human health and productivity. As a result, the influence of indoor environmental quality (IEQ) on the health and productivity of building users becomes a critical field of research that requires immediate attention. As a result, the purpose of this study is to review the state-of-the-art literature by establishing a connection between the factors that influence health and productivity in any given indoor environment.

The methodology involves a thorough review of selected published journals from 1983 to 2021, and the result was analysed through content analysis. The search included journal articles, books and conference proceedings on the critical factors influencing IEQ and their impact on building occupants, which was sourced from different databases such as ScienceDirect, Taylor, GoogleScholar and Web of Science.

The findings from the 90 selected articles revealed four critical factors influencing the quality of the indoor environment and are categorised into; indoor air quality, indoor thermal comfort, visual comfort and acoustic comfort. The findings suggested that when developing a system for controlling the quality of the indoor environment, the indoor air quality, indoor thermal comfort, visual comfort and acoustic comfort should be taken into account.

The indoor environment deeply impacts the health of individuals in their living and work environments. Industry must have a moral responsibility to provide health facilities in which people and workers feel satisfies and give conditions for prosperity. Addressing these essential aspects will not only help the decision-making process of construction professionals but also encourages innovative construction techniques that will enhance the satisfaction, wellness and performance of building occupants.

The paper aims to analyse the social responsibility concept and to explore its role in the implementation process of the tourism sustainability concept. The intention is to explore the way in which the social responsibility concept is implemented in the tourism and analyse how it contributes to its sustainability.

In this interpretivist research, the authors implemented a qualitative strategy using the following methods: content, critical and comparative analyses of the results reported in available scientific studies, categorization, causal analysis and mental mapping. The authors identified 14 thematic categories of research on the tourism social responsibility. For the causal description, the authors used driving force, pressure, state, impact, response (DPSIR) method.

The results include identification of the categories of the research topics concerning tourism social responsibility as well as categories of the approaches to the implementation of the social responsibility into the practice of the tourism sector. The causal description of this implementation process is elaborated in the form of the DPSIR model. The created mental map shows the specific facets of the social responsibility concept applied to the diverse tourism subsectors.

The main contribution lies in basic overview of the conceptual (theoretical) and instrumental (practical) base for implementation of the social responsibility concept into the tourism, providing in this way a critical analysis of examples of the social responsibility practice in the key tourism subsectors. The examination of the causal analyses in the form of DPSIR model as well as employment of the content analyses in the form of mental map represent innovative approach to the tourism responsibility research.

Systemic innovations emerge and create value in an inter-organisational context. However, innovation studies rarely investigate the role of value creation and value capture among multiple organisations in successful innovation implementation. This paper aims to understand the role of value creation and value capture in the implementation of systemic innovations in construction which is by nature, an inter-organisational context.

The empirical research focused on the barriers, enablers and opportunities for value creation and value capture of the Finnish construction project parties when trying to implement mechanical, electrical and plumbing (MEP) prefabrication, which is a systemic innovation. Data were collected through interviews, observations and action workshops.

The empirical study identified interaction patterns on how social, political, technical and economic barriers lead to uneven value capturing, lack of value-based procurement and unclear value creation between MEP design and installation. They hinder the implementation of MEP prefabrication. The results point to enablers leading to fairly shared value to all parties, procurement of value and collaborative value creation, thus increasing the usage of MEP prefabrication, a systemic innovation.

The study adds new knowledge by demonstrating that the identification of barriers and their interaction with enablers and opportunities for value creation and capture lay a baseline for suggestions on how to implement a systemic innovation. This study stresses the importance of enabling value creation and capture for all construction project parties when implementing a systemic innovation.

This paper aims to investigate the phases of new product development within the design-driven innovation (DDI) process, the role of designers and collaborators in the process and how this process relates to some quality principles.

This study adopted a qualitative approach using Gioia methodology. In particular, four Italian manufacturing companies in the home appliances and furniture industry were selected, and data mainly collected through direct interviews were analysed through content analysis.

The new product development related to DDI includes the following phases: the company brief, the designer research, the concept of the designer, the design, legal protection, prototyping, production and the market launch. Designers play a strategic role in the above phases of DDI, but other actors also cooperate and some quality principles affect positively on the process. This study proposes a model for a DDI process in the home appliances and furniture sector.

Although this exploratory study was conducted on only four companies, it advances the DDI research in relation to new product development.

This study makes recommendations to entrepreneurs and managers on how to innovate successfully and to effectively manage designers and collaborators to ensure competition.

This analysis highlights that design-based innovation contributes to improving the quality of life of consumers.

To the best of the authors' knowledge, this is the first qualitative study to examine the phases of new product development in DDI process, the actors involved and relationship to quality principles for the Italian home appliances and furniture sector.