Search results

The purpose of this paper is to present a new modification of the multimodal pushover method, named the target acceleration method. The target acceleration is the minimum acceleration of the base that leads to the ultimate limit state of the structure, i.e., the lowest seismic resistance.

A nonlinear numerical model is used to determine the target acceleration, which is achieved using the iterative procedure according to the envelope principle. Validation of the target acceleration method was conducted on the basis of the results obtained by incremental dynamic analysis.

The influence of higher modes is highly significant. The general failure vector corresponding to the target acceleration differs from the first load vector and the form of the load with uniform acceleration according to the height of structure, as contained in the European Standard EN 1998-1. Comparison between the target acceleration, including the equivalent structural damping, and the failure peak ground acceleration obtained from the dynamic response of the structure exhibits notably good agreement. This result implies that the equivalent structural damping as calculated according to the formulation presented in this paper should be greater than that suggested in the literature.

The originally developed procedure named multimodal pushover target acceleration method can reasonably estimate the minimum acceleration of the base that leads to the ultimate limit state of the structure, and consequently provides a reliable tool for the assessment of the lowest seismic resistance.

This paper aims to evaluate the vulnerability of typical low-rise reinforced concrete (RC) buildings located in Indonesia subjected to tsunami loading.

The vulnerability of typical three-story RC buildings located in Indonesia subjected to tsunami loading is discussed using fragility curves. Buildings without openings in all stories and buildings with openings in the first story are considered. The fragility curves are obtained by performing tsunami pushover analysis for several load cases, using different tsunami load estimation standards and references. The generalized linear method is used as a curve fitting method to construct the fragility curves.

The fragility curves show that the three-story RC buildings without openings in all stories subjected to tsunami loading have a high probability of collapse. Openings in the first story will reduce the vulnerability of the buildings.

Fragility curves are obtained by carrying out tsunami pushover analysis to evaluate the vulnerability of typical three-story RC buildings located in Indonesia. The results of this study show the need to include tsunami loads in the design code for Indonesian buildings and the benefits of having openings in the first story of the building.

The purpose of this paper is to investigate a reinforced concrete multi-storey building with dissipative structural walls. These walls can improve the behaviour of a tall multi-storey building. The authors’ main objective is to evaluate the damage of a building with dissipative walls in comparison with that of a building with solid walls.

In this paper, a comparative nonlinear dynamic analysis between a building with slit walls and then the same building with solid walls is performed by means of SAP2000 software and using a layer model. The solution to increase the seismic performance of a building with structural walls is to create slit zones with short connections in to the walls. The short connections are introduced as a link element with multi-linear pivot hysteretic plasticity behaviour. The hysteretic rules and parameters of these short connections were proposed by the authors and used in this analysis. In this study, the authors propose to evaluate the damage of a building with reinforced concrete slit walls with short connections using seismic analysis.

Using the computational model created by the authors for the slit wall, a seismic analysis of a multi-storey building with slit walls was done. From the results obtained, the advantages of the proposed model are observed.

Using a simple computational model, created by the authors, that consume low processing resources and reduces processing time, a nonlinear dynamic analysis on high-rise buildings was done. Unlike other studies on slit walls with short connections, which are focused mostly on the nonlinear dynamic behaviour of the short connections, in this paper the authors take into consideration the whole structural system, wall, connections and frames.

Post-earthquake fire (PEF) can lead to a rapid collapse of structures partially damaged by earthquake. As there is almost no established PEF provisions by codes and standards, PEF investigations are therefore needed for those buildings. The paper aims to discuss these issues.

A non-linear PEF analysis comprises three steps, which are the application of gravity loads, earthquake loads and then fire loads. As a fire generally initiates on one floor and then spreads to other floors, applying a sequential fire is more realistic than applying a concurrent fire on several floors. Hence, in this study, the fire is applied sequentially to the floors with a time delay.

The results indicate a substantial reduction in the resistance of the damaged frame when subjected to PEF. In addition, the results of applying the PEF sequentially is more realistic than the concurrent fire.

It was better to perform an experimental test to have a better understanding of the issue.

PEF can potentially result in a catastrophe in areas located in seismic regions. Thus, investigating the effect of PEF on previously damaged structures is of importance.

It is well known that the real behaviour of joints lies between the ideal pinned or rigid joint responses. Additionally the influence of this behaviour on the global structural response has been widely studied in the past centred on the plastic resistance or the critical load. On the other hand, there are relatively few studies focusing on the dynamical response of these structures. This paper aims to discuss these issues.

Two types of structures with rigid and semi-rigid joints were considered. Their inelastic response was evaluated using the N2 conventional pushover method, and were later compared to the results from a full non-linear dynamic analysis.

The results indicated that increasing joint flexibility makes the structure less rigid, lengthening its fundamental period and enhancing its horizontal displacement. Furthermore, a parametric study showed that joint flexibility might be of paramount importance to low to medium rise buildings response.

The evaluation of the influence of joint flexibility on the inelastic behaviour of steel structures located in seismic zone is of paramount importance, and is tackled in this paper.

The purpose of this paper is to determine the failure progression resistance of the steel moment-resisting frames subjected to various beam-removal scenarios after application of the design earthquake pertinent to the structure by investigating a generic eight-story building.

The structure is first pushed to arrive at a target roof displacement corresponding to life safety level of performance. To simulate the post-earthquake beam-removal scenario, one of the beam elements is suddenly removed from the structure at a number of different positions. The structural response is then evaluated by using nonlinear static and dynamic analyses.

The results show that while no failure is observed in all of the scenarios, the vulnerability of the upper stories is much greater than that of the lower stories. In the next step, the structural resistance to such scenarios is determined. The results confirm that for the case study structure, at most, the resistance to failure progression in upper stories is 58 percent more than that of lower stories.

Failure and fracture of beam-to-column connections resulting in removal of beam elements may lead to a chain of subsequent failures in other structural members and eventually lead to progressive collapse in some cases. Deficiency in design or construction process of structures when combined by application of seismic loads may lead to such an event.

The high heat induced by fire can substantially decrease the load-bearing capacity, which is more critical in unprotected steel structures than concrete reinforced structures. One of the conventional steel structures is a steel-plate shear wall (SPSW) in which thin infill steel plates are used to resist against the lateral loads. Due to the small thickness of infill plates, high heat seems to dramatically influence the lateral load-bearing capacity of this type of structures. Therefore, this study aims to provide an investigation into the performance of SPSW with reduced beam section at high temperature.

In the present paper, to examine the seismic performance of SPSW at high temperature, 48 single-span single-story steel frames equipped with steel plates with the thicknesses of 2.64 mm, 5 mm and 7 mm and yield stresses of 85 MPa, 165 MPa, 256 MPa and 300 MPa were numerically modeled. Furthermore, their behavioral indices, namely, strength, stiffness, ductility and hysteresis behavior, were studied at the temperatures of 20, 458, 642 and 917? The simulated models in the present paper are based on the experimental specimen presented by Vian and Bruneau (2004).

The obtained results revealed that the high heat harshly diminishes the seismic performance of SPSW so that the lateral strength is reduced even by 95% at substantially high temperatures. Therefore, SPSW starts losing its strength and stiffness at high temperature such that it completely loses its capacity of strength, stiffness and energy dissipation at the temperature of 917? Moreover, it was proved that by separating the percentage of their participations variations of the infill plate in SPSW, their behavior and the bare frame can be examined even at high temperatures.

To the best of the authors’ knowledge, the seismic performance of SPSW at different temperatures has not been evaluated and compared yet.

An analytical investigation is performed on zipper-braced frames. Zipper-braced frames are an innovative bracing system for steel structures. Conventional inverted-V-braced frames exhibit a design problem arising from the unbalanced vertical force generated by the lower story braces when one of them buckles. This adverse effect can be mitigated by adding zipper columns or vertical members connecting the intersection points of the braces above the first floor.

This paper critically evaluates over strength, ductility and response modification factors of these structures. To achieve the purpose of this research, several buildings of different stories are considered. Static pushover analysis, linear dynamic analysis and nonlinear incremental dynamic analysis are performed by OpenSees software concerning ten records of past earthquakes.

Also, ductility factor, over strength factor and response modification factor, has been calculated for zipper-braced frames system. The values of 3.5 and 5 are suggested for response modification factor in ultimate limit state and allowable stress methods, respectively.

The fragility curves were plotted for the first time for such kind of braces. It should be mentioned that these curves play significant roles in evaluating seismic damage of buildings.

Prefabricated columns connected by grouted sleeves are increasingly used in practical projects. However, seismic fragility analyses of such structures are rarely conducted. Seismic fragility analysis has an important role in seismic hazard evaluation. In this paper, the seismic fragility of sleeve connected prefabricated column is analyzed.

A model for predicting the seismic demand on sleeve connected prefabricated columns has been created by incorporating engineering demand parameters (EDP) and probabilities of seismic failure. The incremental dynamics analysis (IDA) curve clusters of this type of column were obtained using finite element analysis. The seismic fragility curve is obtained by regression of Exponential and Logical Function Model.

The IDA curve cluster gradually increased the dispersion after a peak ground acceleration (PGA) of 0.3 g was reached. For both columns, the relative displacement of the top of the column significantly changed after reaching 50 mm. The seismic fragility of the prefabricated column with the sleeve placed in the cap (SPCA) was inadequate.

The sleeve was placed in the column to overcome the seismic fragility of prefabricated columns effectively. In practical engineering, it is advisable to utilize these columns in regions susceptible to earthquakes and characterized by high seismic intensity levels in order to mitigate the risk of structural damage resulting from ground motion.

Fire following an earthquake is an important factor causing damage to buildings and life-line structures. Therefore, besides satisfying structural design requirements for normal loads, such as dead and live loads including the seismic hazard, buildings should also be designed to withstand the fire following earthquakes for a certain minimum duration as required for a desired level of performance. The behavior of a particular reinforced concrete structure that was fire exposed after seismic action is presented in this paper. The seismic response of the structure is evaluated using a pushover analysis, while the displacement demand under the corresponding seismic event is determined using the recommendations implemented in Eurocode 8.