Search results

Real-time monitoring of wound or injured tissues is critical for speedy recovery, and the onset of a cascade of biochemical reactions provides potential biomarkers that facilitate the process of wound monitoring, e.g. pH, temperature, moisture level, bacterial load, cytokines, interleukins, etc. Among all the biomarkers, pH has been known to have a profound impact on the wound healing process, and is used to determine the incidence of bacterial infection of the wound (persistently elevated alkaline pH), proteolytic activity at the site of injury, take rate in skin grafting, wound healing stage and preparation for wound debridement.

This review highlights the significance of pH in determination of clinical parameters and for selection of an appropriate treatment regime, and it presents an in-depth analysis of the designs and fabrication methods that use integrated pH sensors, which have been reported to date for the real-time monitoring of wound healing.

For an expedited wound healing process, the significance of pH mandated the need of an integrated sensor system that would facilitate real-time monitoring of healing wounds and obviate the requirement of redressing or complicated testing procedures, which are both labor-intensive and painful for the patient. The review also discussed different types of sensor systems which were developed using hydrogel as a pH-responsive system coupled with voltammetry, potentiometry, impedimetric and flex-circuit inductive transducer systems. All of the mentioned devices have considerable potential for clinical applications, and there is need of in vivo testing to validate their efficiency and sensitivity under practical scenarios.

This manuscript is an original review of literature, and permission has been granted to use the figures from previously published papers.

The fabrication and characterization of a hydrogel-based conductometric sensor have been carried out. The purpose of this research is to fabricate a small robust hydrogel-based conductometric sensor for real-time monitoring of pH in the physiological range.

A pH-responsive Chitosan/Gelatin composite hydrogel has been used for this purpose. This study reports and analyzes the sensing response obtained from four hydrogel compositions with varying Chitosan/Gelatin ratios. The pH-responsive nature of the hydrogel has been mapped out through volumetric and conductometric tests. An attempt has been made to correlate these characteristics with the physico-chemical nature of the hydrogel through scanning electron microscopy, Fourier transform infrared spectroscopy and X-ray diffraction techniques.

The four hydrogel compositions differed on the basis of gel composition ratios; the conductometric analysis results prove that the sensor with the hydrogel composition (Chitosan 2 per cent, Gelatin 7 per cent, ratio 1:2) produces the best pH resolution in the pH range of 4 to 9. The sensing mechanisms and the differences obtained between individual sensor outputs have been discussed in detail. On the basis of this extensive in vitro assessment, it has been concluded that while key pendant functional groups contribute to pH-responsive characteristics of the hydrogel, the overall sensitivity of the sensors gel component to surrounding pH is also determined by the crystalline to amorphous ratio of the hydrogel composite, its interpenetrating cross-linked structure and the relative ratio of the hydrophilic to the pH-sensitive components.

The conductometric sensor results prove that the fabricated sensor with the shortlisted hydrogel composition shows good sensitivity in the physiological pH range (4 to 9) and it has the potential for use in point of care medical devices for diagnostic purposes.

This is the first reported version of the fabrication and testing and analysis/comparison of a hydrogel-based conductometric sensor based on this composition. The work is original and has not been replicated anywhere.

Additive manufacturing has rapidly developed in terms of technology and its application in various types of industries. With this rapid development, there has been significant research in the area of materials. This has led to the invention of Smart Materials (SMs). The 4D printing is basically 3D printing of these SMs. This paper aims to focus on novel materials and their useful application in various industries using the technology of 4D printing.

Research studies in 4D printing have increased since the time when this idea was first introduced in the year 2013. The present research study will deeply focus on the introduction to 4D printing, types of SMs and its application based on the various types of stimulus. The application of each type of SM has been explained along with its functioning with respect to the stimulus.

SMs have multiple functional applications pertaining to appropriate industries. The 4D printed parts have a distinctive capability to change its shape and self-assembly to carry out a specific function according to the requirement. Afterward, the fabricated part can recover to its 3D printed “memorized” shape once it is triggered by the stimulus.

The present study highlights the various capabilities of SMs, which is used as a raw material in 4D printing.

This paper aims to develop a novel micro-ablation system to realise micrometric and well-defined hydrogel structures. To engineer a tissue it is necessary to evaluate several aspects, such as cell-cell and cell-substrate interactions, its micro-architecture and mechanical stimuli that act on it. For this reason, it is important to fabricate a substrate which presents a microtopology similar to natural tissue and has chemical and mechanical properties able to promote cell functions. In this paper, well-defined hydrogel structures embedding cells were microfabricated using a purposely developed technique, micro-laser ablation, based on a thulium laser. Its working parameters (laser power emission, stepper motor velocity) were optimised to produce shaded “serpentine” pattern on a hydrogel film.

In this study, initially, swelling/contraction tests on agarose and alginate hydrogel in different solutions of main components of cell culture medium were performed and were compared with the MECpH model. This comparison matched with good approximation experimental measurements. Once known how hydrogel changed its topology, microstructures with a well-defined topology were realised using a purposely developed micro-laser ablation system design. S5Y5 neuroblastoma cell lines were embedded in hydrogel matrix and the whole structure was ablated with a laser microfabrication system. The cells did not show damages due to mechanical stress present in the hydrogel matrix and to thermal increase induced by the laser beam.

The hydrogel structure is able to reproduce extracellular matrix. Initially, the hydrogel swelling/contraction in different solutions, containing the main components of the most common cell culture media, was analysed. This analysis is important to evaluate if cell culture environment could alter microtopology of realised structures. Then, the same topology was realised on hydrogel film embedding neuronal cells and the cells did not show damages due to mechanical stress present in the hydrogel matrix and to thermal increase induced by the laser beam. The interesting obtained results could be useful to realise well-defined microfabricated hydrogel structures embedding cells to guide tissue formation

The originality of this paper is the design and realisation of a 3D microfabrication system able to microfabricate hydrogel matrix embedding cells without inducing cell damage. The ease of use of this system and its potential modularity render this system a novel potential device for application in tissue engineering and regenerative medicine area.

Active employment of additive manufacturing for scaffolds preparation requires the development of advanced methods which can accurately characterize the morphologic structure and its changes during an interaction of the scaffolds with substrate and aqueous medium. This paper aims to use the method of nuclear magnetic resonance (NMR) imaging for preclinical characterization of 3D-printed scaffolds based on novel allyl chitosan biocompatible polymer matrices.

Biocompatible polymer scaffolds were fabricated via stereolithography method. Using NMR imaging the output quality control of the scaffolds was performed. Scaffolds stability, polymer matrix homogeneity, kinetic of swelling processes, water migration pathways within the 3D-printed parts, effect of post-print UV curing on overall scaffolds performance were studied in details.

NMR imaging visualization of water uptake and polymer swelling processes during the interaction of scaffolds with aqueous medium revealed the formation of the fronts within the polymer matrices those dynamics is governed by case I transport (Fickian diffusion) of the water into polymer network. No significant difference was observed in front propagation rates along the polymer layers and across the layers stack. After completing the swelling process, the polymer scaffolds retain their integrity and no internal defects were detected.

NMR imaging revealed that post-print UV curing aimed to improve the overall performance of 3D-printed scaffolds might not provide a better quality of the finish product, as this procedure apparently yield strongly inhomogeneous distribution of polymer crosslink density which results in subsequent inhomogeneity of water ingress and swelling processes, accompanied by stress-related cracks formation inside the scaffolds.

This study introduces a method which can successfully complement the standard tests which now are widely used in either additive manufacturing or scaffolds engineering.

This work can help to improve the overall performance of the polymer scaffolds used in tissue engineering.

The results of this study demonstrate feasibility of NMR imaging for preclinical characterization of 3D printed biocompatible polymer scaffolds. The results are believed to contribute to better understanding of the processes vital for improving the design of 3D-printed polymer scaffolds.

This paper aims to present the numerical analysis of displacements, forces and bend angles of three different structural designs of a soft actuator using the finite element method. The results of this analysis help understand the physical behavior of the soft pneumatic actuator.

The soft actuator is designed using commercial modeling software, and the design of the actuator is analyzed using ABAQUS 19.0 with a standard implicit nonlinear analysis. There are three types of structural designs for actuators, namely, rectangular-base model, trapezoidal-base model and the trapezoidal model considered in the present study.

Maximum displacement, force and bend angle are observed in the rectangular-base model at various pressure levels.

The development of novel designs of the soft pneumatic actuator to undertake a comparative analysis of displacement, force and bend angle.

In this study, fabrication of polymer and cotton fabric exhibiting stimuli-responsive wetting and water vapor permeability features together with antibacterial activity was aimed.

Temperature and pH-responsive poly(N-isopropyl acrylamide-graft-chitosan) (PNIPAM-g-CS) copolymer were produced via the free radical addition polymerization method and fixed to the cotton fabric using butane tetracarboxylic acid (BTCA) cross-linker by double-bath impregnation method. The chemical structure of the graft copolymer was characterized by Fourier-transform infrared spectroscopy (FT-IR) spectroscopy and H-Nuclear magnetic resonance (1H NMR) analyses. Thermo-responsive behavior of the fabric was investigated by wetting time and water uptake tests, contact angle measurement and surface energy calculation. Additionally, antibacterial activity of the fabric treated with copolymer was studied against S. aureus bacterium.

PNIPAM-g-CS graft copolymer was synthesized successfully, which had lower critical solution temperature (LCST) value of 32 °C and exhibited thermo-responsive property. The treated fabrics exhibited hydrophilic character at temperatures below the LCST and hydrophobic character at temperatures above the LCST. It was found that polymer-coated fabric could have regulated the water vapor permeability by the change in its pore size and hydrophilicity depending on the temperature. Additionally, treated fabric displayed a pH-responsive water absorption behavior and strong antibacterial activity against S.aureus bacterium.

In the study, it has been shown that the cotton fabrics can be fabricated which have antibacterial activity and capable of pH and temperature responsive smart moisture/water management by application of copolymer. It is thought that the fabric structures developed in the study will be promising in the production of medical textile structures where antibacterial activity and thermophysiological comfort are important.

Methylene blue (MB) is classified as a cationic dye which is widely used as chemical indicator, coloring agent and biological stain. The discharge of this dye to the water streams is harmful to the human beings. For this reason, this study investigated the removal of MB from aqueous solution by hydrogel nanocomposite.

In experimental part, at first, ultraviolet (UV)-curable hydrogel/chitosan nanocomposite, which improves its elasticity by urethane acrylate, was synthesized and characterized by FTIR and SEM analysis. Afterward, the synthesized hydrogel nanocomposite was applied for the removal of MB and the influence of operational condition including nanocomposite loading, dye concentration, contact time and pH of solution was specified. Moreover, isotherm studies as well as kinetics survey were performed.

Langmuir, Freundlich, Brunauer, Emmett and Teller and Tempkin adsorption isotherms were assessed for the analysis of experimental data indicating the Freundlich isotherm was the best fitted one. The adsorption kinetics data was examined indicating the adsorption kinetics appropriate to pseudo-second-order kinetics model.

The predominant water absorption property of the UV-curable hydrogel/chitosan nanocomposite to 8.5 steps and outstanding adsorption capacity for the elimination of MB on hydrogel nanocomposite subscribed that the synthesized hydrogel could be a favorable adsorbent for simultaneous absorption of water and removal of cationic dyes.

This paper aims to propose a suitable atomizing solidification chitosan (CS) gel liquid extrusion molding technology for the three dimensional (3D) printing method, and experiments verify the feasibility of this method.

This paper mainly uses experimental means, combined with theoretical research. The preparation method, solidification forming method and 3D printing method of CS gel solution were studied. The CS gel printing mechanism and printing error sources are analyzed on the basis of the CS gel ink printing results, printing performance with different ratios of components by constructing a gel print prototype, experiments evaluating the CS gel printing technology and the effects of the process parameters on the scaffold formation.

CS printing ink was prepared; the optimal formula was found; the 3 D printing experiment of CS was completed; the optimal printing parameters were obtained; and the reliability of the forming prototype, printing ink and gel printing process was verified, which allowed for the possibility to apply the 3 D printing technology to the manufacturing of a CS gel structure.

This study can provide theoretical and technical support for the potential application of CS 3 D printed gels in tissue engineering.

A novel grafted temperature-responsive ReO₄⁻ Imprinted composite membranes (Re-ICMs) was successfully prepared by using polyvinylidene fluoride (PVDF) resin membranes as substrates, this study aimed to separate and purify ReO effectively.

Re-ICMs were synthesized by PVDF resin membranes as the substrate, acrylic acid (AA), acrylamide (AM), ethylene glycol dimethacrylate (EGDMA) were functional monomers. The morphology and structure of Re-ICMs were characterized by scanning electron microscope and Fourier transform infrared spectroscopy.

The maximum adsorption capacity toward ReO₄⁻ was 0.1,163 mmol/g and the separation decree had relation to MnO₄⁻ was 19.3. The optimal operation conditions were studied detailedly and the results as follows: the molar ratios of AA, AM, EGDMA, ascorbic acid, NH4ReO₄, were 0.8, 0.96, 0.02, 0.003 and 0.006. The optimal time and temperature were 20 h and 40°C, respectively. The Langmuir and pseudo-second-order models were fit these adsorption characteristics well.

Rhenium (Re) is mainly used to chemical petroleum and make superalloys for jet engine parts. This study was representing a technology in separate and purify of Re, which provided a method for the development of the petroleum and aviation industry.

This contribution provided a novel method to separate ReO₄⁻ from MnO₄⁻. The maximum adsorption capacity was 0.1163 mmol/g at 35°C and the adsorption equilibrium time was within 2 h. Meanwhile, the adsorption selectivity rate ReO₄⁻/MnO₄⁻ was 19.3 and the desorption rate was 78.3%. Controlling the adsorption experiment at 35°C and desorption experiment at 25°C in aqueous solution, it could remain 61.3% of the initial adsorption capacity with the adsorption selectivity rate of 13.3 by 10 adsorption/desorption cycles, a slight decrease, varied from 78.3% to 65.3%, in desorption rate was observed.