Search results

As an advanced manufacturing method, additive manufacturing (AM) technology provides new possibilities for efficient production and design of parts. However, with the continuous expansion of the application of AM materials, subtractive processing has become one of the necessary steps to improve the accuracy and performance of parts. In this paper, the processing process of AM materials is discussed in depth, and the surface integrity problem caused by it is discussed.

Firstly, we listed and analyzed the characterization parameters of metal surface integrity and its influence on the performance of parts and then introduced the application of integrated processing of metal adding and subtracting materials and the influence of different processing forms on the surface integrity of parts. The surface of the trial-cut material is detected and analyzed, and the surface of the integrated processing of adding and subtracting materials is compared with that of the pure processing of reducing materials, so that the corresponding conclusions are obtained.

In this process, we also found some surface integrity problems, such as knife marks, residual stress and thermal effects. These problems may have a potential negative impact on the performance of the final parts. In processing, we can try to use other integrated processing technologies of adding and subtracting materials, try to combine various integrated processing technologies of adding and subtracting materials, or consider exploring more efficient AM technology to improve processing efficiency. We can also consider adopting production process optimization measures to reduce the processing cost of adding and subtracting materials.

With the gradual improvement of the requirements for the surface quality of parts in the production process and the in-depth implementation of sustainable manufacturing, the demand for integrated processing of metal addition and subtraction materials is likely to continue to grow in the future. By deeply understanding and studying the problems of material reduction and surface integrity of AM materials, we can better meet the challenges in the manufacturing process and improve the quality and performance of parts. This research is very important for promoting the development of manufacturing technology and achieving success in practical application.

The presence of heavy metals in milk causes many acute and chronic physiological dysfunctions in human organs. The present study aims to investigate the heavy metals in cow's and buffalo's milk of two major cities, Karachi and Gujranwala, Pakistan to estimate metal intake by humans from this source.

In total, 48 milk samples from 2 cities were drawn from animals' udder to avoid contamination. Each sample was digested with nitric acid at 105 ^oC (degree Celsius) on a pre-heated electric hot plate to investigate the metals by atomic absorption spectroscopy (flame type). Air-acetylene technique analyzed chromium, cadmium and lead, and the hydride method analyzed arsenic in the milk samples.

The results revealed the highest mean lead concentration (19.65 ± 43.86 ppb) in the milk samples, followed by chromium (2.10 ± 2.33 ppb) and arsenic (0.48 ± 0.73 ppb). Cadmium was not detected in any sample, assuming cadmium's occurrence was below the detection level. The concentrations of all the metals in the samples of the two cities do not differ statistically. Lead concentrations in the buffalo's milk were higher than in cow's milk (p < 0.05). However, the concentrations of arsenic and chromium between buffalo's and cow's milk do not differ statistically. The present study reveals a lower level of metals in the milk than those conducted elsewhere. The mean concentrations of all the metals met the World Health Organization's (WHO) safety guidelines (1993).

Although cadmium causes toxicity in the human body, cadmium could not be measured because cadmium's concentration was below the detection level, which is 1 ppb.

This study will help reduce the toxic metals in our environment, and the sources of heavy metals, particularly from the industrial sector could be identified. The feed and water consumed by the milking animals could be carefully used for feeding them.

This study will help reduce the diseases and malfunction of human organs and organ systems since these heavy metals cause toxicity and carcinogenicity in humans. Arsenic and chromium cause cancer while lead causes encephalopathy (a brain disease).

The study reports heavy metal concentrations in the two attributes of four independent variables of raw milk samples that were scarcely reported from Pakistan.

This study aims to examine the metal pollution in coastal sediment in the Peninsular Malaysia.

Approximately 141 published studies were screened from 1,285 documents and reviewed to determine the existing pollution status in the coastal areas of Peninsular Malaysia and the metals under review were Pb, Hg, Cd, Ar, Cu, Zn, Cr and Ni. Sources of pollutants and their effect on biological systems, marine organisms and human health were addressed in this review as well as recommendation of heavy metal removal or remedies in short. Emphasis is placed on marine pollution, particularly on the toxic metal accumulation in biota.

This study has revealed the different concentrations of pollutants, low, moderately, and chronically contaminated areas from heavy metals and the consequences to aquatic ecosystem and indirectly to human health, since an increasing in the coastal developments in Peninsular Malaysia.

This study has revealed the different concentrations of pollutants, low, moderately, and chronically contaminated areas from heavy metals and the consequences to aquatic ecosystem and indirectly to human health, since an increasing in the coastal developments in Peninsular Malaysia.

Korea and China have promoted a bilateral FTA since 2005 to upgrade their economic relationships. If the Korea-China FTA is concluded, then trade between the two countries is likely to involve substantial changes both quantitatively and qualitatively. Offer lists submitted by Korea include steel, petrochemicals and machinery and those by China include some agricultural and marine products as well as nonferrous metals. Korea's interest in the Korea-China FTA has focused mainly on damage to the agricultural sector and there have been a lot of studies on the effects of the FTA on Korean agricultural sector. However, little is known about why China includes the nonferrous metals industry for early voluntary liberalization and its implications for the domestic economy. Nonferrous metals industry is one of China’s national strategic sectors and has a large supply excess in the country. This study targets the survey of Chinese nonferrous metals industry and trade structure and considers the problem of nonferrous metals in the context of negotiations for the Korea-China FTA and its implications for a higher-quality Korea-China FTA.

To reduce the heat load of a gas turbine blade, its surface is covered with an outer layer of ceramics with high thermal resistance. The purpose of this paper is the selection of ceramics with such a low heat conduction coefficient and thickness, so that the permissible metal temperature is not exceeded on the metal-ceramics interface due to the loss ofmechanical properties.

Therefore, for given temperature changes over time on the metal-ceramics interface, temperature changes over time on the inner side of the blade and the assumed initial temperature, the temperature change over time on the outer surface of the ceramics should be determined. The problem presented in this way is a Cauchy type problem. When analyzing the problem, it is taken into account that thermophysical properties of metal and ceramics may depend on temperature. Due to the thin layer of ceramics in relation to the wall thickness, the problem is considered in the area in the flat layer. Thus, a one-dimensional non-stationary heat flow is considered.

The range of stability of the Cauchy problem as a function of time step, thickness of ceramics and thermophysical properties of metal and ceramics are examined. The numerical computations also involved the influence of disturbances in the temperature on metal-ceramics interface on the solution to the inverse problem.

The computational model can be used to analyze the heat flow in gas turbine blades with thermal barrier.

A number of inverse problems of the type considered in the paper are presented in the literature. Inverse problems, especially those Cauchy-type, are ill-conditioned numerically, which means that a small change in the inputs may result in significant errors of the solution. In such a case, regularization of the inverse problem is needed. However, the Cauchy problem presented in the paper does not require regularization.