Search results

1 – 10 of 29
Article
Publication date: 26 September 2019

Di Yang and Zhiming Gao

A finite volume scheme for diffusion equations on non-rectangular meshes is proposed in [Deyuan Li, Hongshou Shui, Minjun Tang, J. Numer. Meth. Comput. Appl., 1(4)(1980)217–224…

Abstract

Purpose

A finite volume scheme for diffusion equations on non-rectangular meshes is proposed in [Deyuan Li, Hongshou Shui, Minjun Tang, J. Numer. Meth. Comput. Appl., 1(4)(1980)217–224 (in Chinese)], which is the so-called nine point scheme on structured quadrilateral meshes. The scheme has both cell-centered unknowns and vertex unknowns which are usually expressed as a linear weighted interpolation of the cell-centered unknowns. The critical factor to obtain the optimal accuracy for the scheme is the reconstruction of vertex unknowns. However, when the mesh deformation is severe or the diffusion tensor is discontinuous, the accuracy of the scheme is not satisfactory, and the author hope to improve this scheme.

Design/methodology/approach

The authors propose an explicit weighted vertex interpolation algorithm which allows arbitrary diffusion tensors and does not depend on the location of discontinuity. Both the derivation of the scheme and that of vertex reconstruction algorithm satisfy the linearity preserving criterion which requires that a discretization scheme should be exact on linear solutions. The vertex interpolation algorithm can be easily extended to 3 D case.

Findings

Numerical results show that it maintain optimal convergence rates for the solution and flux on 2 D and 3 D meshes in case that the diffusion tensor is taken to be anisotropic, at times heterogeneous, and/or discontinuous.

Originality/value

This paper proposes a linearity preserving and explicit weighted vertex interpolation algorithm for cell-centered finite volume approximations of diffusion equations on general grids. The proposed finite volume scheme with the new interpolation algorithm allows arbitrary continuous or discontinuous diffusion tensors; the final scheme is applicable to arbitrary polygonal grids, which may have concave cells or degenerate ones with hanging nodes. The final scheme has second-order convergence rate for the approximate solution and higher than first-order accuracy for the flux on 2 D and 3 D meshes. The explicit weighted interpolation algorithm is easy to implement in three dimensions in case that the diffusion tensor is continuous or discontinuous.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 30 no. 3
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 29 August 2019

Gang Peng, Zhiming Gao, Wenjing Yan and Xinlong Feng

This paper aims to consider numerical simulation for radionuclide transport calculations in geological radioactive waste repository.

Abstract

Purpose

This paper aims to consider numerical simulation for radionuclide transport calculations in geological radioactive waste repository.

Design/methodology/approach

The nonlinear two-point flux approximation is used to discretize the diffusion flux and has a fixed stencil. The cell-vertex unknowns are applied to define the auxiliary unknowns and can be interpolated by the cell-centered unknowns. The approximation of convection flux is based on the second-order upwind method with a slope limiter.

Findings

Numerical results illustrate that the positivity-preserving is satisfied in solving this convection-diffusion system and has a second-order convergence rate on the distorted meshes.

Originality/value

A new positivity-preserving nonlinear finite volume scheme is proposed to simulate the far-field model used in the geological radioactive waste repository. Numerical results illustrate that the positivity-preserving is satisfied in solving this convection-diffusion system and has a second-order convergence rate on the distorted meshes.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 30 no. 2
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 19 June 2019

Yunxia Sun, Xufeng Xiao, Zhiming Gao and Xinlong Feng

The purpose of this paper is to propose an efficient space-time operator-splitting method for the high-dimensional vector-valued Allen–Cahn (AC) equations. The key of the…

Abstract

Purpose

The purpose of this paper is to propose an efficient space-time operator-splitting method for the high-dimensional vector-valued Allen–Cahn (AC) equations. The key of the space-time operator-splitting is to devide the complex partial differential equations into simple heat equations and nolinear ordinary differential equations.

Design/methodology/approach

Each component of high-dimensional heat equations is split into a series of one-dimensional heat equations in different spatial directions. The nonlinear ordinary differential equations are solved by a stabilized semi-implicit scheme to preserve the upper bound of the solution. The algorithm greatly reduces the computational complexity and storage requirement.

Findings

The theoretical analyses of stability in terms of upper bound preservation and mass conservation are shown. The numerical results of phase separation, evolution of the total free energy and total mass conservation show the effectiveness and accuracy of the space-time operator-splitting method.

Practical implications

Extensive 2D/3D numerical tests demonstrated the efficacy and accuracy of the proposed method.

Originality/value

The space-time operator-splitting method reduces the complexity of the problem and reduces the storage space by turning the high-dimensional problem into a series of 1D problems. We give the theoretical analyses of upper bound preservation and mass conservation for the proposed method.

Details

International Journal of Numerical Methods for Heat & Fluid Flow, vol. 29 no. 9
Type: Research Article
ISSN: 0961-5539

Keywords

Article
Publication date: 23 February 2024

Guangwei Liang, Zhiming Gao, Cheng-Man Deng and Wenbin Hu

The purpose of this study is to reveal the effect of nano-Al2O3 particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of…

Abstract

Purpose

The purpose of this study is to reveal the effect of nano-Al2O3 particle addition on the nucleation/growth kinetics, microhardness, wear resistance and corrosion resistance of Co–P–xAl2O3 nanocomposite plating.

Design/methodology/approach

The kinetics and properties of Co–P–xAl2O3 nanocomposite plating prepared by electroplating were investigated by electrochemical measurements, scanning electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy, Vickers microhardness measurement, SRV5 friction and wear tester and atomic force microscopy.

Findings

A 12 g/L nano-Al2O3 addition in the plating solution can transform the nucleation/growth kinetics of the plating from the 3D progressive model to the 3D instantaneous model. The microhardness of the plating increased with the increase of nano-Al2O3 content in plating. The wear resistance of the plating did not adhere strictly to Archard’s law. An even and denser corrosion product film was generated due to the finer grains, with a high corrosion resistance.

Originality/value

The effect of different nano-Al2O3 addition on the nucleation/growth kinetics and properties of Co–P–xAl2O3 nanocomposite plating was investigated, and an anticorrosion mechanism of Co–P–xAl2O3 nanocomposite plating was proposed.

Details

Anti-Corrosion Methods and Materials, vol. ahead-of-print no. ahead-of-print
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 5 June 2023

Huiyi Xu, Zhiming Gao, Yang Yang and Wenbin Hu

The purpose of this study is to ensure the safe use of carbon fiber composite pressure vessels in the nuclear industry environment.

Abstract

Purpose

The purpose of this study is to ensure the safe use of carbon fiber composite pressure vessels in the nuclear industry environment.

Design/methodology/approach

This study investigated the degradation behaviors of carbon fiber reinforced composite (CFRP) using the specific corrosive media HF solution, with a focus on the damage to the surface epoxy layer. The degradation behaviors of CFRP in HF solution were examined by electrochemical methods and surface characterization, using HCl, NaCl and NaF solution for comparison.

Findings

The results showed that the specimen in HF solution will have a value of |Z|0.01 Hz one order of magnitude lower, a substantially lower contact angle, more breakage of the surface epoxy and the stronger O─H peak and weaker C─O─C peak in the Fourier transform infrared spectrum, indicating severe hydrolytic damage to the surface epoxy.

Originality/value

The work focuses on the degradation damage to CFRP surface epoxy by specific corrosive media HF.

Details

Anti-Corrosion Methods and Materials, vol. 70 no. 4
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 7 November 2022

Lupeng Liu, Senlin Li, Zhiming Gao, Hang Jia and Wenbin Hu

This paper aims to study the effect of chloride concentration on the properties of passive film formed on Q235 steel in simulated concrete pore solutions.

Abstract

Purpose

This paper aims to study the effect of chloride concentration on the properties of passive film formed on Q235 steel in simulated concrete pore solutions.

Design/methodology/approach

Mott–Schottky analysis and electrochemical impedance spectroscopy were used to study the passive film of Q235 steel in simulated concrete pore solution. X-ray photoelectron spectroscopy was used to analyze the composition of passive film on Q235 steel.

Findings

When the chloride concentration is below the chloride threshold value, open circuit potential (OCP) and Rct gradually increases and donor concentration (ND) remains unchanged with the increasing immersion time. When the chloride concentration exceeds chloride threshold value, OCP and Rct decreases after a temporary increase and ND increases. The linear region of the Mott–Schottky curve lost its linearity. The electrochemical process control step is changed from charge transfer control to oxygen diffusion control. As the chloride concentration increases, the FeO content in the passive film increases and the Fe2O3 content decreases. Chloride can destroy the outer layer of passive film and introduce impurities.

Originality/value

The effects of chloride and immersion time on the change process of passive films on Q235 steel in simulated concrete pore solution were studied using electrochemical methods. The mechanism of chloride destroying passive film was analyzed.

Details

Anti-Corrosion Methods and Materials, vol. 70 no. 1
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 26 January 2023

Dejing Zhou, Mingyang Wang, Yuanyuan Ji, Zhe Liu, Zhiming Gao, Wenbin Hu and Yuhua Guo

This paper aims to investigate the electrochemical corrosion behavior of a five-layer Al alloy composites (4343/4047/3003/4047/4343) with a thickness of 0.2 mm in NaCl solution.

Abstract

Purpose

This paper aims to investigate the electrochemical corrosion behavior of a five-layer Al alloy composites (4343/4047/3003/4047/4343) with a thickness of 0.2 mm in NaCl solution.

Design/methodology/approach

Electrochemical impedance spectroscopy, polarization curve and morphology analyses were used to study the corrosion behavior of the Al alloy composites from cross-sectional and plane directions.

Findings

The corrosion resistance of the surface from the plane direction was higher than that from the cross sections. Si-enrich particles were observed in the outer 4047/4343 layer, and AlFeCuMnBi phases were identified in the core 3003 layer. The galvanic coupling between the Si-enrich particle and the Al matrix accelerated the dissolution Al matrix.

Originality/value

This work lays the experimental foundation for corrosion mechanism of the Al alloy composite plate.

Details

Anti-Corrosion Methods and Materials, vol. 70 no. 2
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 4 September 2020

Jian Song, Zhiming Gao, Chenxi Liu and Wenbin Hu

This paper aims to study the effect of flow rate (0.42∼2.09 m/s) on the corrosion behavior of WB36CN1 steel pipe in the simulated secondary circuit water environment (170°C, 6…

Abstract

Purpose

This paper aims to study the effect of flow rate (0.42∼2.09 m/s) on the corrosion behavior of WB36CN1 steel pipe in the simulated secondary circuit water environment (170°C, 6 mg/L ethanolamine + 100 µg/L NaCl), for which an autoclave was used to simulate the secondary circuit environment for carrying out related experiments.

Design/methodology/approach

The corrosion behaviors were studied by electrochemical methods, morphological observations and elemental analysis.

Findings

As flow rate increases, the amplitude of the current noise fluctuates increased, noise resistance Rn and spectral noise resistance Rsn decreased, the shear stress on the surface of WB36CN1 steel increases, the oxygen content on the surface decreases, the roughness becomes smaller. Meanwhile, the energy of energy distribution plot is concentrated at high frequencies under the three flow conditions, the slopes of current power spectral density curve approach 0 db/decade. This means that the oxide on the surface becomes less and corrosion rate increases with increasing flow rate. The corrosion type of WB36CN1 steel was uniform corrosion; the degree of uniform corrosion is higher at high flow rate.

Originality/value

The effect of flow rate on the corrosion behavior of WB36CN1 steel pipe in the secondary circuit water environment was studied by using electrochemical methods in the laboratory. The effect mechanism of flow rate for corrosion behavior was obtained.

Details

Anti-Corrosion Methods and Materials, vol. 67 no. 5
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 7 June 2021

Shixiong Wu, Zhiming Gao, Da-Hai Xia, Meijun Wu, Yingjie Liu and Wenbin Hu

This paper aims to study the effect of temperature on the process and kinetic parameters of the hydrogen evolution reaction of X80 under cathodic protection (CP) in 3.5% NaCl…

Abstract

Purpose

This paper aims to study the effect of temperature on the process and kinetic parameters of the hydrogen evolution reaction of X80 under cathodic protection (CP) in 3.5% NaCl solution.

Design/methodology/approach

Potentiodynamic polarization combined with the hydrogen permeation test is used to analyze the hydrogen evolution reaction (HER) process and the rate-determining step for which is diagnosed through the electrochemical impedance spectrum method. Then, the influence of temperature on kinetic parameters of HER can be known from the results obtained by using the Iver-Pickering-Zamenzadeh model for data analysis.

Findings

The results show that the HER proceeds through Volmer–Tafel route with the Volmer reaction acting as the rate-controlling step; Increasing temperature gives a higher activity of the HER on X80, it also accelerates the hydrogen desorption and diffusion of hydrogen into the metal.

Originality/value

There exist few studies on the topic of how temperature affects the HER process. It is imperative to conduct a relevant study to give some instruction in cathodic protection system design and this paper fulfills this need.

Details

Anti-Corrosion Methods and Materials, vol. 68 no. 3
Type: Research Article
ISSN: 0003-5599

Keywords

Article
Publication date: 17 March 2022

Yanming Xia, Dejing Zhou, Zhiming Gao and Wenbin Hu

This paper aims to study the effect of Hg2+ on the corrosion behavior of Al–2%Zn coatings on AA5083 in 3.5 Wt.% NaCl solution.

Abstract

Purpose

This paper aims to study the effect of Hg2+ on the corrosion behavior of Al–2%Zn coatings on AA5083 in 3.5 Wt.% NaCl solution.

Design/methodology/approach

Potentiodynamic polarization and electrochemical impedance spectroscopy are used to investigate the effect of Hg2+ on the corrosion behavior. The surface and cross-sectional morphology are characterized by scanning electron microscopy and energy dispersive spectroscopy (EDS) to further reveal the corrosion mechanism of Hg2+.

Findings

The results show that the corrosion behavior of the coating changes significantly as the concentration of Hg2+ increases from 5 to 30 μg/L. The corrosion production film can inhibit the corrosion process when Hg2+ concentration is in the range of 0.5–5 μg/L, while Hg2+ can promote the corrosion process significantly when its concentration reaches to 30 μg/L. The generation rate of dense oxide film on the coating surface is faster than dissolution rate when the concentration of Hg2+ is in the range of 0–5 μg/L, which makes the coating “self-healing” and thus slightly slows down the corrosion rate. The EDS analysis shows that excessive Hg2+ are preferentially deposited at locations with inhomogeneous electrochemical properties, which in turn accelerates corrosion.

Originality/value

The corrosion resistance of Al-based coatings is significantly affected by Hg2+ in seawater. Thus, it is important to explain the corrosion mechanism of Al–2%Zn coatings under the combined effect of Hg2+ and Cl in 3.5 Wt.% NaCl solution.

Details

Anti-Corrosion Methods and Materials, vol. 69 no. 3
Type: Research Article
ISSN: 0003-5599

Keywords

1 – 10 of 29