Search results

It is a huge technical and engineering challenge to realize the precise assembly of thousands of large optics in high power solid-state laser system. Using the 400-mm aperture-sized transport mirror as a case, this paper aims to present an intelligent numerical computation methodology for mounting performance analysis and modeling of large optics in a high-power laser system for inertial confinement fusion (ICF).

Fundamental principles of modeling and analysis of the transport mirror surface distortion are proposed, and a genetic algorithm-based computation framework is proposed to evaluate and optimize the assembly and mounting performance of large laser optics.

The stringent specifications of large ICF optics place very tight constraints upon the transport mirror’s assembly and mounts. The operational requirements on surface distortion [peak-to-valley and root mean square (RMS)] can be met as it is appropriately assembled by the close loop of assembly-inspection-optimization-fastening. In the end, the experimental study validates the reliability and effectiveness of the transport mirror mounting method.

In the assembly design and mounting performance evaluation of large laser optics, the whole study has the advantages of accurate evaluation and intelligent optimization on nano-level optical surface distortion, which provides a fundamental methodology for precise assembly and mounting of large ICF optics.

A chromate conversion coating was prepared on the surface of bare AA2024 aluminum alloy by direct immersion in the chromating treatment bath, and the corrosion behavior of chromated AA2024 aluminum alloy in 3.5 per cent NaCl solution was studied by electrochemical measurement and microstructural observation.

According to the polarization curve test and the scanning electron microscope observation, the corrosion evolution of chromated AA2024 in 3.5 per cent NaCl solution was divided into the following three stages: coating failure, pitting corrosion and intergranular corrosion (IGC).

In the first stage, the chromate coating degraded gradually due to the combined action of chloride anions and water molecules, resulting in the complete exposure of AA2024 substrate to 3.5 per cent NaCl solution. Subsequently, in the second stage, chloride anions adsorbed at the sites of θ phase (Al2Cu) and S phase (Al2CuMg) on the AA2024 surface preferentially, and some corrosion pits initiated at the above two sites and propagated towards the deep of crystal grains. However, the propagation of a pit terminated when the pit front arrived at the adjacent grain boundary, where the initiation of IGC occurred.

Finally, in the third stage, the corrosion proceeded along the continuous grain boundary net and penetrated the internal of AA2024 substrate, resulting in the propagation of IGC. The related corrosion mechanisms for the bare and the chromated AA2024 were also discussed.

This paper aims to study the impact of manufacturer’s upgrading strategy of durable products on the retailer’s decision on trade-in program and her decision on the secondary market.

This paper develops a channel that consists of a manufacturer and a retailer, where the manufacturer releases an upgraded product, and the retailer introduces a trade-in program for consumers, simultaneously, decides whether to enter the secondary market. These approaches are modeled through Stackelberg game.

This paper reveals that the optimal conditions for manufacturer to release upgraded products and retailer to resell used products in the secondary market, and it reveals that under what conditions it is profitable for retailer to enter the secondary market under product upgrade levels.

If the manufacturer’s upgrade level is low, it is profitable for the retailer to enter the secondary market. However, if the manufacturer’s upgrade level is high, it is unprofitable for the retailer to enter the secondary market.

In this paper, the active secondary market, upgrading of new products, consumer market segmentation and especially, the upgrade degree of new products as a function of consumer demand are considered simultaneously.

The aim of this work was to propose a method to prepare composite phosphate conversion coating (CPCC), including ternary phosphate conversion coating (TPCC) and binary phosphate conversion coatings (BPCC), with one-step chemical conversion and to reveal and compare the corrosion resistance between TPCC and BPCC.

In this work, a calcium–manganese–zinc (Ca–Mn–Zn) TPCC was prepared on the surface of magnesium alloy (MA) AZ91D with one-step chemical conversion method; for Ca-Mn-Zn@TPCC, its microstructure was characterized with scanning electron microscope observation and scanning tunneling microscope detection, and its composition was characterized with energy dispersion spectroscopy and X-ray photoelectron spectroscopy analyses. Particularly, the corrosion resistance of Ca-Mn-Zn@TPCC and its comparison with Ca–Mn, Ca–Zn and Mn–Zn BPCCs were clarified with electrochemical and immersion measurements.

Ca-Mn-Zn@TPCC, which was composed of Ca, Mn, Zn, P and O, exhibited a mud-shaped with cracks microstructure, and the average crack width, terrain fluctuation and coating thickness were 0.61 µm, 23.78 nm and 2.47 µm, respectively. Ca-Mn-Zn@TPCC provided good corrosion resistance to MA AZ91D; in NaCl solution, the total degradation of Ca-Mn-Zn@TPCC consumed eight days; corrosion products with poor adhesion peeled out from Ca-Mn-Zn@TPCC-coated MA AZ91D spontaneously. Besides, the corrosion resistance of Ca-Mn-Zn@TPCC was better than that of Ca-Mn@BPCC, Ca-Zn@BPCC or Mn-Zn@BPCC.

The successful preparation of Ca-Mn-Zn@TPCC on MA AZ91D surface confirmed the proposed method to prepare CPCC with one-step chemical conversion was feasible; at the same time, it was further confirmed that for phosphate conversion coating, ternary coating had better corrosion resistance than binary coating did.

The purpose of this work is to reveal the mechanism of WO₄²⁻ on surface passivation for Q235 carbon steel in tungstate solution.

In Na₂WO₄ solutions with the different concentrations of WO₄²⁻, the spontaneous passivation occurred on the surface of Q235 carbon steel when the concentration of WO₄²⁻ was up to 0.13 mmol/L, which was attributed to the formations of the inner deposition film and the outer adsorption film on the Q235 surface under the action of WO₄²⁻.

The inner deposition film presented a two-layer microstructure: the inside layer was composed of Fe₂O₃ mainly, and the outside layer comprised Fe(OH)2•nH₂O, Fe(OH)3•nH₂O, FeWO₄ and Fe₂(WO₄)3.

Both FeWO₄ and Fe₂(WO₄)3 repaired the defects in the outside layer of the inner deposition film; however, the outer adsorption film played a more important role in the surface passivation than the inner deposition film did.

The purpose of this paper is to reveal the mechanism of nitrite (NO_2⁻) for the surface passivation of carbon steels in acidic environments through investigating the influences of 0.01 mol/L NaNO₂ addition on the corrosion and passivation behaviors of Q235 carbon steel in acidic phosphate buffer (APB) solutions (pH 2 to 6).

The electrochemical techniques including open circle potential evolution, potentiodynamic polarization, electrochemical impedance spectroscopy and cyclic voltammetry were applied.

In APB solutions without NO_2⁻, the Q235 steel presented the electrochemical behaviors of activation (A), activation-passivation-transpassivation and self-passivation-transpassivation at pH 2 to 4, pH 5 and pH 6, respectively; the corrosion rate decreased with the up of pH value, and the surface passivation occurred in the pH 5 and pH 6 solutions only: the anodic passivation at pH 5 and the spontaneous passivation at pH 6.

In APB solutions without NO_2⁻, the corrosion rate decreased with the up of pH value, and the surface passivation occurred in the pH 5 and pH 6 solutions only: the anodic passivation at pH 5 and the spontaneous passivation at pH 6. With the addition of 0.01 mol/L NaNO₂, into APB solutions, the variation of corrosion rate showed the same rule, but the surface passivation occurred over the whole acidic pH range, including the anodic passivation at pH 2 to 4 and the spontaneous passivation at pH 5 to 6.

This paper aims to present a closed-loop supply chain (CLSC) optimization problem for a perishable agricultural product to achieve three pillars of sustainability, including minimizing total network costs and carbon dioxide emissions from different network activities and maximizing responsiveness to demands simultaneously.

The research problem is formulated as a multi-objective mixed-integer linear programming model, and classical approaches, including the LP-Metric and weighted Tchebycheff method, have been applied to solve the optimization model. A set of test problems has been proposed to validate the model, and the results are presented.

Computational time to find Pareto optimal solutions by using the weighted Tchebycheff method was twice as much as that of the LP-Metric method. Also, the result of the study is a mathematical model that can be applied to other products that are close to the fruit, such as vegetables.

The present study is limited to fruits supply chains and the inventory is considered at the distribution centers only. The study also considers only one type of transport.

The paper can assist supply chain managers to define strategies to achieve a sustainable CLSC network configuration for the fruits.

This study is one of the early studies to consider environmental indicators in fruits supply chain design along with two other indicators of sustainability, namely, economic and social indicators. Therefore, this can help supply chain managers to achieve sustainability by optimizing location decisions, inventory quantities and flow between facilities.

After receiving advertising messages, most consumers rarely purchase the advertised products at once, which results in a delay between advertising exposure and its effect. This paper is devoted to exploring the advertising decision and coordination issues for a supply chain system subject to advertising immediate and delayed effects.

By applying the game theory, the differential game models with delay are constructed for the supply chain to examine the equilibrium advertising efforts, brand goodwill and the optimal profits under the different cooperation situations. A class of transfer payment contracts is designed to achieve the best outcome of the supply chain. Illustrative examples are given to demonstrate the effectiveness of addressed results and provide some managerial perspectives.

It can be found that the complete cooperation situation can stimulate the advertising investment, drive the product demand and improve the economic profit. Also, a class of transfer payment contracts is designed in this paper, such that the supply chain can perfectly realize the profit maximization, and each member can achieve the Pareto improvement.

This work does not address the random market environment, which can be filled in the future. Furthermore, this paper has been done in a single supply chain structure. It is an interesting future line of research when taking competitive behavior (e.g. competition among manufacturers, retailers or supply chains) into account.

This study will help managers make advertising strategies, advise an optimal cooperation way and design the coordination contracts to ensure the economic development of the supply chain. These obtained conclusions may provide a valuable decision-support for marketing management.

For a supply chain, the most previous literature about dynamic advertising models focused on a single advertising effect-immediate effect. This work explores advertising strategy with double advertising effects and investigates the coordinating power of new transfer payment contracts.

The aims of this study are to conduct a systematic review of public–private partnership (PPP) studies published from 2009 to 2019, to compare the results with Ke et al. (2009) who reviewed the PPP literature published from 1998 to 2008, and to trace the evolution of the PPP knowledge in the past two decades. This study also presents the possible directions that the PPP research may go towards in the future, arguably.

This study carried out a top journal-based search to identify the quality PPP articles published from 2009 to 2019. A total of 12 top-tier construction journals were systematically searched in the database of web of science (WOS), from which 279 PPP articles were identified for review.

The number of the identified articles, the titles of the journals, institutions, the most cited papers, and prevalent research methods were analyzed and compared. The existing PPP studies in construction journals were classified into seven streams. Through analysis of the PPP research status and gaps, five future research directions were revealed.

This study contributes to the current body of knowledge by revealing the research trend of PPP from 2009 to 2019. It presents the change of PPP development trend in the past decade through comparison with Ke et al. (2009). It also reveals the major research streams and points out the directions that the PPP research may go towards in the future. Moreover, this study is helpful to the practice as well. It can enhance the practitioners' understanding of the PPP development in the past decade. In addition, it identified the research institutions contributing the most in the area of PPP, which may serve as valuable reference for practitioners to locate the best institutions for consultancy or collaboration.