Search results

This paper aims to evaluate the influence of molybdenum disulfide (MoS₂) concentrations (5, 7.5, 10, 12.5 and 15 Wt.%) on the microstructure and tribological property of the self-lubrication cubic boron nitride (CBN) abrasive composites.

Three point bending method and rotating sliding test are used to evaluate the flexural strength and tribological property of self-lubricating CBN abrasive composites. Microstructure, wear morphology of the ball and scratch are supported by scanning electron microscopy, optical microscope and three-dimensional confocal microscopy, etc.

The MoS₂ concentration has a significant influence on the interface microstructure between CBN abrasives and matrix alloys, and thus, affects the flexural strength of CBN abrasive composites. The grain fracture modes of CBN abrasive composites are transformed from the transgranular fracture into intergranular fracture as the MoS₂ concentrations increase. Additionally, the friction coefficient of as-sintered samples decreases with the MoS₂ concentrations. The MoS₂ concentrations of 10 Wt.% are final determined to fabricate self-lubricating composites in basis of the mechanical and lubricating property.

The ball is fabricated under vacuum sintering process. The tribological property of self-lubricating CBN abrasive composites is evaluated in terms of the friction coefficient and morphologies of the ball and scratches after rotating sliding tests.

Grinding may generate high temperature along the arc of grinding zone, especially during the grinding process of difficult‐to‐machine materials. It can cause thermal damage to the ground surface and poor surface integrity. Conventional cooling methods based on large amounts of water‐oil emulsions can be both ineffective and environmentally unacceptable. The purpose of this paper is to offer a new high efficiency cooling method – cryogenic pneumatic mist jet cooling (CPMJ) to enhance heat transfer in the grinding zone during grinding of difficult‐to‐machine materials.

CPMJ equipment is a set up, which can produce water mist of −5°C with jet velocity above 150 m/s and mean particle size below 20 μm at the impingement distance of 10‐40 mm on the symmetry axis. To validate the cooling efficiency of CPMJ equipment, heat transfer experiments were carrying out on it. Finally, CPMJ was applied to the grinding of titanium alloy to verify its cooling effects.

With high penetrative power and water mist of −5°C, CPMJ can greatly improve heat transfer efficiency in the grinding zone. Experimental results, including heat transfer experiments and grinding experiments, indicate that CPMJ has strong cooling ability and can offer better cooling effects compared with cold air jet and traditional flood cooling method. With CPMJ cooling method, grinding zone temperature can be effectively reduced and good surface quality can be achieved during grinding of titanium alloy.

CPMJ cooling method is an effective and pollution‐free way to solve the thermal problems during grinding of difficult‐to‐machine materials.

This study aims to enhance the lubrication performance of thrust bearings. The influence of columnar convex–concave compound microtexture on bearing performance is investigated

Based on the compound microtexture model of thrust bearings, considering surface roughness and turbulent effect, the variation of lubrication characteristics with the change in the compound microtexture parameters is studied.

The results indicate that, compared with circular microtexture, the maximum pressure of compound microtexture of thrust bearings increases by 7.42%. Optimal bearing performance is achieved when the internal microtexture depth is 0.02 mm. Turbulent flow states and surface roughness lead to a reduction in the optimal depth. The maximum pressure and load-carrying capacity of the bearing decrease as the initial angle increases, whereas the friction coefficient increases with the increase in the initial angle. The lubrication performance is best for bearings with a circumferential parallel arrangement of microtexture.

The novel composite microtexture with columnar convex-concave is proposed, and the computational model of thrust bearings is set. The influence of surface roughness and turbulent flow on the bearing performance should be considered for better conforming with engineering practice. The effect of microtexture depth, arrangement method and distribution position on the lubrication performance of the compound microtexture thrust bearing is investigated, which is of great significance for improving tribology, thrust bearings and surface microtexture theory.