Search results

Using wire as feedstock has several advantages for additive manufacturing (AM) of metal components, which include high deposition rates, efficient material use and low material costs. While the feasibility of wire-feed AM has been demonstrated, the accuracy and surface finish of the produced parts is generally lower than those obtained using powder-bed/-feed AM. The purpose of this study was to develop and investigate the feasibility of a fine wire-based laser metal deposition (FW-LMD) process for producing high-precision metal components with improved resolution, dimensional accuracy and surface finish.

The proposed FW-LMD AM process uses a fine stainless steel wire with a diameter of 100 µm as the additive material and a pulsed Nd:YAG laser as the heat source. The pulsed laser beam generates a melt pool on the substrate into which the fine wire is fed, and upon moving the X–Y stage, a single-pass weld bead is created during solidification that can be laterally and vertically stacked to create a 3D metal component. Process parameters including laser power, pulse duration and stage speed were optimized for the single-pass weld bead. The effect of lateral overlap was studied to ensure low surface roughness of the first layer onto which subsequent layers can be deposited. Multi-layer deposition was also performed and the resulting cross-sectional morphology, microhardness, phase formation, grain growth and tensile strength have been investigated.

An optimized lateral overlap of about 60-70% results in an average surface roughness of 8-16 µm along all printed directions of the X–Y stage. The single-layer thickness and dimensional accuracy of the proposed FW-LMD process was about 40-80 µm and ±30 µm, respectively. A dense cross-sectional morphology was observed for the multilayer stacking without any visible voids, pores or defects present between the layers. X-ray diffraction confirmed a majority austenite phase with small ferrite phase formation that occurs at the junction of the vertically stacked beads, as confirmed by the electron backscatter diffraction (EBSD) analysis. Tensile tests were performed and an ultimate tensile strength of about 700-750 MPa was observed for all samples. Furthermore, multilayer printing of different shapes with improved surface finish and thin-walled and inclined metal structures with a minimum achievable resolution of about 500 µm was presented.

To the best of the authors’ knowledge, this is the first study to report a directed energy deposition process using a fine metal wire with a diameter of 100 µm and can be a possible solution to improving surface finish and reducing the “stair-stepping” effect that is generally observed for wires with a larger diameter. The AM process proposed in this study can be an attractive alternative for 3D printing of high-precision metal components and can find application for rapid prototyping in a range of industries such as medical and automotive, among others.

The use of a gas metal arc welding-based weld-deposition, referred to as wire-direct energy deposition or wire-arc additive manufacturing, is one of the notable additive manufacturing methods for producing metallic components at high deposition rates. In this method, the near-net shape is manufactured through layer-by-layer weld-deposition on a substrate. However, as a result of this sequential weld-deposition, different layers are subjected to different types of thermal cycles and partial re-melting. The resulting microstructural evolution of the material may not be uniform. Hence, the purpose of this study is to assess microstructure variation along with the lamination direction (or build direction).

The study was carried out for two different boundary conditions, namely, isolated condition and cooled condition. The microstructural evolution across the layers is hypothesized based on experimental assessment; this included microhardness, scanning electron microscopy imaging and electron backscatter diffraction analysis. These conditions subsequently collaborated with the help of thermal modeling of the process.

During a new layer deposition, the previous layer also is subject to re-melt. While the newly added layer undergoes rapid cooling through a combination of convection, conduction and radiation losses, the penultimate layer, sees a slower cooling curve due to its smaller exposure area. This behavior of rapid-solidification and subsequent re-melting and re-solidification is a progressing phenomenon across the layers and the bulk of the layers have uniform grains due to this remelt-re-solidification phenomenon.

This paper studies the microstructure variation along with the build direction for thin-walled components fabricated through weld-deposition. This study would be helpful in addressing the issue of anisotropy resulting from the distinctive thermal history of each layer in the overall theme of metal additive manufacturing.

The unique aspect of this paper is the postulation of a generic hypothesis, based on experimental findings and supported by thermal modeling of the process, for remelt-re-solidification phenomenon followed by temperature raising/lowering repetitively in every layer deposition across the layers. This is implemented for different types of base plate conditions, revealing the role of boundary conditions on the microstructure evolution.

The purpose of this paper is to find a theoretical reference to adjust the unsymmetrical arc shape and plasma flow of overlapping deposition in wire arc additive manufacturing (WAAM) and ensure the effect of the gas shielding and stable heat and mass transfer in deposition process. The multiphysical numerical simulation and physical experiment are used for validation.

In this study, welding torch tilt deposition and external parallel magnetic field–assisted deposition are presented to adjust the unsymmetrical arc shape and plasma flow of overlapping deposition, and a three-dimensional numerical model is developed to simulate the arc of torch tilt overlapping deposition and external parallel magnetic field–assisted overlapping deposition.

The comparison of simulated results indicate that the angle of welding torch tilt equal to 20° and the magnetic flux density of external transverse magnetic field equal to 0.001 Tesla are capable of balancing the electric arc and shielding gas effectively, respectively. The arc profiles captured by a high-speed camera match well with simulated results.

These studies of this paper can provide a theoretical basis and reference for the calibration and optimization of WAAM process parameters.

Electron beam-based additive manufacturing (EBAM) is an emerging technology to produce metal parts layer-by-layer. The purpose of this paper is to systematically address the research and development carried out for this technology, up till now.

This paper identifies several aspects of research and development in EBAM.

Electron beam has several unique advantages such as high scanning speed, energy efficiency, versatility for several materials and better part integrity because of a vacuum working environment.

This paper provides information on different aspects of EBAM with the current status and future scope.

A wire-based additive manufacturing system works with high manufacturing efficiency and low dimensional precision. The purpose of this paper is to study the dimensional characteristics of Ti-6Al-4V thin-walled parts with wire-based multi-laser additive manufacturing in vacuum.

Wire-based multi-laser additive manufacturing was carried out to understand the effect brought from different parameters. The Ti-6Al-4V thin-walled parts were formed by different height increments, power inputs and inter-layer cooling times in vacuum.

The result shows that, with the number of layers increment, the layer width of thin-walled part increases gradually in the beginning and stabilizes soon afterward. Height increment, laser power and inter-layer cooling time could affect the energy input to the deposited bead and heat accumulation of thin-walled part. The layer width decreases, while the height increment increases. The increment of laser power could increase the layer width. And, the increment of inter-layer cooling time (more than 5 s) has little effect on the layer width.

The heat dissipation mode of thin-walled parts in vacuum and the influence of different parameters on layer width are explained in this paper. It provides a reference for further understanding and controlling dimension precision of Ti-6Al-4V thin-walled part with wire-based multi-laser additive manufacturing in vacuum. At the same time, it provides a reference for researches of dimensional characteristics in the additive manufacturing industry.

The purpose of this paper is to develop a build strategy for inclined thin-walled parts by exploiting the inherent overhanging capability of the cold metal transfer (CMT) process, which release wire-arc additive manufacturing from tedious programming work and restriction of producible size of parts.

Inclined thin-walled parts were fabricated with vertically placed welding torch free from any auxiliary equipment. The inclined features were defined and analyzed based on the geometrical model of inclined parts. A statistical prediction model was developed to describe the dependence of inclined geometrical features on process variables. Based on these models, a build strategy was proposed to plan tool path and output process parameters. After that, the flow work was illustrated by fabricating a vase part.

The formation mechanism and regulation of inclined geometrical features were revealed by conducting experimental trials. The inclined angle can be significantly increased along with the travel speed and offset distance, whereas the wall width is mainly dependent on the ratio of wire feed speed to travel speed. In contrast to other welding process, CMT has a stronger overhanging capability, which provides the possibility to fabricate parts with large overhanging features directly with high forming accuracy.

This paper describes a novel build strategy for inclined thin-walled parts free from any auxiliary equipment. With the proposed strategy, a complex structural component can be deposited directly in the rectangular coordinates additive manufacturing system, indicating infinite possibilities on the producible size of the parts. Moreover, equipment requirements and tedious program work can also be significantly reduced.

This study aims to propose and evaluate the progress in the basic-pixel (a strategy to generate continuous trajectories that fill out the entire surface) algorithm towards performance gain. The objective is also to investigate the operational efficiency and effectiveness of an enhanced version compared with conventional strategies.

For the first objective, the proposed methodology is to apply the improvements proposed in the basic-pixel strategy, test it on three demonstrative parts and statistically evaluate the performance using the distance trajectory criterion. For the second objective, the enhanced-pixel strategy is compared with conventional strategies in terms of trajectory distance, build time and the number of arcs starts and stops (operational efficiency) and targeting the nominal geometry of a part (operational effectiveness).

The results showed that the improvements proposed to the basic-pixel strategy could generate continuous trajectories with shorter distances and comparable building times (operational efficiency). Regarding operational effectiveness, the parts built by the enhanced-pixel strategy presented lower dimensional deviation than the other strategies studied. Therefore, the enhanced-pixel strategy appears to be a good candidate for building more complex printable parts and delivering operational efficiency and effectiveness.

This paper presents an evolution of the basic-pixel strategy (a space-filling strategy) with the introduction of new elements in the algorithm and proves the improvement of the strategy’s performance with this. An interesting comparison is also presented in terms of operational efficiency and effectiveness between the enhanced-pixel strategy and conventional strategies.

Additive manufacturing (AM) is a rapidly evolving manufacturing process, which refers to a set of technologies that add materials layer-by-layer to create functional components. AM technologies have received an enormous attention from both academia and industry, and they are being successfully used in various applications, such as rapid prototyping, tooling, direct manufacturing and repair, among others. AM does not necessarily imply building parts, as it also refers to innovation in materials, system and part designs, novel combination of properties and interplay between systems and materials. The most exciting features of AM are related to the development of radically new systems and materials that can be used in advanced products with the aim of reducing costs, manufacturing difficulties, weight, waste and energy consumption. It is essential to develop an advanced production system that assists the user through the process, from the computer-aided design model to functional components. The challenges faced in the research and development and operational phase of producing those parts include requiring the capacity to simulate and observe the building process and, more importantly, being able to introduce the production changes in a real-time fashion. This paper aims to review the role of robotics in various AM technologies to underline its importance, followed by an introduction of a novel and intelligent system for directed energy deposition (DED) technology.

AM presents intrinsic advantages when compared to the conventional processes. Nevertheless, its industrial integration remains as a challenge due to equipment and process complexities. DED technologies are among the most sophisticated concepts that have the potential of transforming the current material processing practices.

The objective of this paper is identifying the fundamental features of an intelligent DED platform, capable of handling the science and operational aspects of the advanced AM applications. Consequently, we introduce and discuss a novel robotic AM system, designed for processing metals and alloys such as aluminium alloys, high-strength steels, stainless steels, titanium alloys, magnesium alloys, nickel-based superalloys and other metallic alloys for various applications. A few demonstrators are presented and briefly discussed, to present the usefulness of the introduced system and underlying concept. The main design objective of the presented intelligent robotic AM system is to implement a design-and-produce strategy. This means that the system should allow the user to focus on the knowledge-based tasks, e.g. the tasks of designing the part, material selection, simulating the deposition process and anticipating the metallurgical properties of the final part, as the rest would be handled automatically.

This paper reviews a few AM technologies, where robotics is a central part of the process, such as vat photopolymerization, material jetting, binder jetting, material extrusion, powder bed fusion, DED and sheet lamination. This paper aims to influence the development of robot-based AM systems for industrial applications such as part production, automotive, medical, aerospace and defence sectors.

The presented intelligent system is an original development that is designed and built by the co-authors J. Norberto Pires, Amin S. Azar and Trayana Tankova.

The purpose of this paper is to study the functionality of additively manufactured (AM) parts, mainly depending on their dimensional accuracy and surface finish. However, the products manufactured using AM usually suffer from defects like roughness or uneven surfaces. This paper discusses the various surface quality improvement techniques, including how to reduce surface defects, surface roughness and dimensional accuracy of AM parts.

There are many different types of popular AM methods. Unfortunately, these AM methods are susceptible to different kinds of surface defects in the product. As a result, pre- and postprocessing efforts and control of various AM process parameters are needed to improve the surface quality and reduce surface roughness.

In this paper, the various surface quality improvement methods are categorized based on the type of materials, working principles of AM and types of finishing processes. They have been divided into chemical, thermal, mechanical and hybrid-based categories.

The review has evaluated the possibility of various surface finishing methods for enhancing the surface quality of AM parts. It has also discussed the research perspective of these methods for surface finishing of AM parts at micro- to nanolevel surface roughness and better dimensional accuracy.

This paper represents a comprehensive review of surface quality improvement methods for both metals and polymer-based AM parts.

Twin-wire welding-based additive manufacturing (TWAM) is a unique process which uses gas metal arc welding (GMAW)-based twin-wire weld-deposition to create functionally gradient materials (FGMs). Presented study aims to focus on creating metallic objects with a hardness gradient using GMAW of twin-wire weld deposition setup.

By using dissimilar filler wires in twin-wire weld-deposition, it is possible to create metallic objects with varying hardness. This is made possible by individually controlling the proportion of each filler wire used. ER70S-6 and ER110S-G are the two filler wires used for the study; the former has lower hardness than the latter. In the current study, methodology and various experiments carried out to identify the suitable process parameters at a given location for a desired variation of hardness have been presented. A predictive model for obtaining the wire speed of the filler wires required for a desired value of hardness was also created. Subsequently, sample parts with gradient in various directions have been fabricated.

For dissimilar twin-wire weld-deposition used here, it is observed that the resultant hardness is in the volumetric proportion of the hardness of the individual filler wires. This aids the fabrication of FGMs using arc based weld-deposition with localized control of hardness, achieved through the control of the ratio of wire speeds of the individual filler wires. Four sample parts were fabricated to demonstrate the concept of realizing FGMs through TWAM. The fabricated parts showed good match with the desired hardness variation.

This paper successfully presents the capability of TWAM for creating gradient metallic objects with varying hardness. Although developed using ER70S-6 and ER110S-G filler wire combination, the methodology can be extended for other filler wire combinations too for creating FGMs

GMAW-based twin-wire welding for additive manufacturing is a novel process which uses dissimilar filler wires for creating FGMs. This paper describes methodology of the same followed by illustration of parts created with bi-directional hardness gradient.