Search results

The authors aim to search for a practical and accurate way to get good loss estimates for coil filaments in electrical machines, for example transformers. At the moment including loss estimations into standard finite element computations is prohibitively expensive for large coils.

A low-dimensional function space for finite element method (FEM) is introduced on the filament-air interface and then extended into the filament to significantly reduce the number of unknowns per filament. Careful choice of these extensions enables good loss estimate accuracy. The result is a system matrix assembly block that can be used verbatim for all filaments, further reducing the cost. Both net current and voltage per length of the filament are readily available in the problem formulation.

The loss estimates from the developed model agree well with traditional FEM and the computation times are faster.

To produce accurate loss estimates in large coils, the low-dimensional function space is constricted on the filament boundaries. The proposed method enables electrical engineers to compute the ohmic losses of individual conductors.

Discusses the 27 papers in ISEF 1999 Proceedings on the subject of electromagnetisms. States the groups of papers cover such subjects within the discipline as: induction machines; reluctance motors; PM motors; transformers and reactors; and special problems and applications. Debates all of these in great detail and itemizes each with greater in‐depth discussion of the various technical applications and areas. Concludes that the recommendations made should be adhered to.

The purpose of this paper is to devise an analytical approach to calculate conductor winding losses, considering multiple contributing aspects simultaneously. These include the geometric configuration of coil windings, frequency of the electric current and the dependency on the coil temperature, derived studying a coupled fluid–solid model considering the cooling system characteristics. The obtained results allow identifying power loss trends according to such system variables as coolant inlet temperature or overall flow rate of the motor.

An easy-to-use coupled analytical approach is applied, which is suitable for rapid estimations of the impact of parameter variation on the resulting conductor winding power losses that facilitates decision-making in the design process of electric aircraft engines.

In the considered cooling parameters, the overall conductor winding power losses vary approximately between 6 kW and 7.2 kW. More than 95 per cent of this loss is because of direct current losses. These losses cause the variation in maximal coil temperature ranging between 115°C and 170°C.

The SP260D motor is set and was currently tested in Extra 330. It recently broke two world records.

One of the current trends in aircraft engineering is electric aircraft. Advantages of electric aircraft include improved manoeuvrability because of greater torque from electric motors, increased safety because of decreased chance of mechanical failure, less risk of explosion or fire in the event of a collision and less noise. There will be environmental and cost benefits associated with the elimination of dependency on fossil fuels and resultant emissions.

The use of a novel fluid–solid interaction model for predicting conductor winding power loss of the SP260D electric aircraft motor has not been done earlier. A novel alternative derivation of the widely applied Dowell’s formula (Dowell, 1966) is presented for the estimation of proximity losses in square winding conductors.

To prevent the coil from burning or getting damaged, it is necessary to estimate the duration of its operation as long as its temperature does not exceed the permissible limit. This paper aims to investigate the effect of switching on the thermal behavior of impregnated and nonimpregnated windings. Also, the safe operating time for each winding is determined.

The power loss of the winding is expressed as a function of the winding specifications. Using homogenization techniques, the equivalent thermal properties for the homogenized winding are calculated and used in a proposed thermal equivalent circuit for winding modeling and analysis. The validity and accuracy of the proposed model are determined by comparing its analysis results and simulation and measurement results.

The results show that copper windings have better thermal behavior and lower temperature compared to aluminum windings. On the other hand, by impregnating or increasing the packing factor of the winding, the thermal behavior is improved. Also, by choosing the right duty cycle for the winding current source, it is possible to prevent the burning or damage of the winding and increase its lifespan. Comparing the measurement results with the analysis results shows that the proposed equivalent circuit has an error of less than 4% in the calculation of the winding center temperature.

In this paper, the effect of temperature on the electrical resistance of the coil is ignored. Also, rectangular wires were not investigated. Research in these topics are considered as future work.

By calculating the thermal time constant of the winding, its safe operation time can be calculated so that its temperature does not exceed the tolerable value (150 °C). The proposed method analyzes both impregnated and nonimpregnated windings with various schemes. It investigates the effects of switching on their thermal behavior. Additionally, it determines the safe operating time for each type of winding.

The purpose of this paper is to analyse the stray losses in the windings of permanent magnet synchronous machines (PMSM).

The 2D field model, based on the edge element method (EEM) and

-V formulation, has been developed and utilized for the determination and analysis of stray losses in the PMSM with concentrated windings made of strip conductors. The influence of the supply frequency as well as the slot opening width on the losses caused by eddy currents has been examined. The different arrangements of the conductors in the tape wound coils have been studied. The obtained results have been compared to the reference case when the eddy current effect is neglected.

The usefulness of the proposed methodology of the stray losses evaluation has been tested on the case study problem. It has been observed that the stray losses in the windings of the considered machine can be reduced by choosing the proper value of the slot opening. The dependence of the stray losses on the frequency of the supply currents has been examined. The obtained results show that with the increase of frequency the stray losses caused by the eddy currents in the strip conductors increase.

The proposed 2D field numerical model makes it possible to analyse the stray losses in the tape wound concentrated windings of the PMSM motor. The presented model can be utilized for the optimization of the magnetic circuit of the machine with the aim of minimizing eddy current losses.

An excessive increase in temperature will reduce the lifespan and even burn the coil. The variety of materials in the structure of the electromagnet along with its multi-layer winding creates a complex and heterogeneous thermal structure. There are very few researches that are completely focused on the thermal analysis of electromagnets. The purpose of this paper is to provide an accurate, yet fast and simple method for the thermal analysis of cylindrical electromagnets in both transient and steady-state modes. For this purpose, a thermal equivalent circuit (TEC) is presented based on the nodding approach.

The results of TEC analysis of cylindrical electromagnet, for two orthogonal and orthocyclic winding coil technologies, were compared with the results of the thermal simulation in COMSOL. The authors also built a laboratory model of the cylindrical electromagnet, similar to those analyzed and simulated, and measured the temperature in different parts of it.

The comparison of the results obtained from different methods for the thermal analysis of the cylindrical electromagnet indicates that the proposed TEC has an error of less than 2%. The simplicity and high accuracy of the results are the most important advantages of the proposed TEC.

Comparing the information and results related to winding schemes, indicates that the orthogonal winding has less cost and weight due to the shorter length of the wire used. On the other hand, orthocyclic winding generates lower temperature and has more lifting force, and is simpler to implement. Therefore, in practice, orthocyclic winding technology is usually used.

The purpose of this paper is to propose a simplified thermal circuit to estimate the temperature rise in the winding of a totally enclosed fan cooled electric motor for different loads and/or cooling conditions since the motor has already been tested for a known condition.

The determination of the convection resistance is based on classical Nusselt correlations and the value of conduction resistance is provided from a known load condition and the corresponding temperature rise in the winding.

Predicted temperature values showed good agreement with the experimental results, demonstrating that the hypothesis of simplification to a punctual source of thermal energy is acceptable.

It is necessary that the motor has already been tested for a known condition (losses, temperature, and ventilation). Although the basic idea of this methodology is based on the use of a reference test condition of the same motor, as a suggestion, with small modifications the same methodology can be used to estimate the thermal behavior of different sized motors, provided a similar motor has already been tested.

This approach results in a fast methodology to estimate the thermal behavior of an electric motor in different loads and/or cooling conditions.

The differential of this circuit is the use of only two thermal resistances, one for the whole conduction and the other for the convection. This approach is a way to overcome the difficulties related to the determination of the thermal contact resistance and the equivalent conduction resistance between the winding and the different isolation systems inside the slots.

The purpose of this paper is to discuss a new method of iron loss estimation under pulse width modulation (PWM) converter supply. The proposed method concerns the longitudinal magnetisation.

A novel method of iron loss estimation applies values of iron losses that come from a single higher harmonic coexisting with a DC‐bias field. This method considers non‐linearity of ferromagnetic. Results of estimation are validated using experimental results.

The paper formulates that the dependence of iron losses come from harmonics, on DC‐bias field. Moreover, it formulates possibilities of their utilization to iron loss estimation in case of deformed flux. On the other hand, it discusses the influence of DC‐bias field on static hysteresis and classical eddy current losses.

Experimental verification will still be needed as to the accuracy of the proposed model and applicability to various magnetic materials.

The paper provides an easy mathematical method of iron loss estimation, under PWM voltage supply.

The paper explains how to use an analytical method and results of iron losses come from single harmonics, obtained under coexistence with DC‐bias field, to iron loss estimation in case of longitudinal magnetisation where deformed magnetic flux occurs.

This paper aims to give a perspective about the variety of techniques which are available and are being further developed in the area of coupled field formulations, with selective bibliography and practical examples, to help postgraduate students, researchers and designers working in design or analysis of electrical machinery.

This paper reviews the recent trends in coupled field formulations. The use of these formulations for designing and non‐destructive testing of electrical machinery is described, followed by their classifications, solutions and applications. Their advantages and shortcomings are discussed.

The paper gives an overview of research, development and applications of coupled field formulations for electrical machinery based on more than 160 references. All landmark papers are classified. Practical engineering case studies are given which illustrate wide applicability of coupled field formulations.

Problems which continue to pose challenges to researchers are enumerated and the advantages of using the coupled‐field formulation are pointed out.

This paper gives a detailed description of the application of the coupled field formulation method to the analysis of problems that are present in different electrical machines. Examples of analysis of generators and transformers with this formulation are presented. The application examples give guidelines for its use in other analyses.

The coupled‐field formulation is used in the analysis of rotational machines and transformers where reference data are available and comparisons with other methods are performed and the advantages are justified. This paper serves as a guide for the ongoing research on coupled problems in electrical machinery.

A distinction must be drawn between a dismissal on the one hand, and on the other a repudiation of a contract of employment as a result of a breach of a fundamental term of that contract. When such a repudiation has been accepted by the innocent party then a termination of employment takes place. Such termination does not constitute dismissal (see London v. James Laidlaw & Sons Ltd (1974) IRLR 136 and Gannon v. J. C. Firth (1976) IRLR 415 EAT).